Handles, Locks, Latches And Entry Systems DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B10AB:00 | Remote Keyless Entry Synchronization: No Sub Type Information | GO to Pinpoint Test R |
| B10C6:01 | Exterior Trunk Antenna: General Electrical Failure | GO to Pinpoint Test X |
| B10C7:01 | Interior Trunk Antenna: General Electrical Failure | GO to Pinpoint Test W |
| B1218:00 | Transmitter Identification Code: No Sub Type Information | GO to Pinpoint Test R |
| B126A:01 | Drivers Door Interior Lock Switch: General Electrical Failure | GO to Pinpoint Test J |
| B1336:01 | Left Front External Antenna: General Electrical Failure | GO to Pinpoint Test V |
| B1337:01 | Right Front Door External Antenna: General Electrical Failure | GO to Pinpoint Test V |
| B1381:11 | Left Front Door Handle Proximity Sensor: Circuit Short To Ground | GO to Pinpoint Test V |
| B1381:15 | Left Front Door Handle Proximity Sensor: Circuit Short To Battery or Open | GO to Pinpoint Test V |
| B1381:29 | Left Front Door Handle Proximity Sensor: Signal Invalid | GO to Pinpoint Test V |
| B1382:11 | Right Front Door Handle Proximity Sensor: Circuit Short To Ground | GO to Pinpoint Test V |
| B1382:15 | Right Front Door Handle Proximity Sensor: Circuit Short To Battery or Open | GO to Pinpoint Test V |
| B1382:29 | Right Front Door Handle Proximity Sensor: Signal Invalid | GO to Pinpoint Test V |
| B1383:11 | Left Rear Door Handle Proximity Sensor: Circuit Short To Ground | GO to Pinpoint Test V |
| B1383:15 | Left Rear Door Handle Proximity Sensor: Circuit Short To Battery or Open | GO to Pinpoint Test V |
| B1383:29 | Left Rear Door Handle Proximity Sensor: Signal Invalid | GO to Pinpoint Test V |
| B1384:11 | Right Rear Door Handle Proximity Sensor: Circuit Short To Ground | GO to Pinpoint Test V |
| B1384:15 | Right Rear Door Handle Proximity Sensor: Circuit Short To Battery or Open | GO to Pinpoint Test V |
| B1384:29 | Right Rear Door Handle Proximity Sensor: Signal Invalid | GO to Pinpoint Test V |
| B14B8:11 | Sounder: Circuit Short To Ground | GO to Pinpoint Test O |
| B14B8:15 | Sounder: Circuit Short To Battery or Open | GO to Pinpoint Test O |
| B14B8:15 | Sounder: Circuit Short To Battery or Open | GO to Pinpoint Test P |
| B1560:49 | Driver Side Keypad: Internal Electronic Failure | GO to Pinpoint Test Q |
| B1561:49 | Passenger Side Keypad: Internal Electronic Failure | GO to Pinpoint Test Q |
| B1585:11 | Central Lock Output: Circuit Short To Ground | GO to Pinpoint Test I |
| B1585:12 | Central Lock Output: Circuit Short To Battery | GO to Pinpoint Test I |
| B1585:13 | Central Lock Output: Circuit Open | GO to Pinpoint Test I |
| B1586:11 | Central Unlock Output: Circuit Short To Ground | GO to Pinpoint Test I |
| B1586:12 | Central Unlock Output: Circuit Short To Battery | GO to Pinpoint Test I |
| B1586:13 | Central Unlock Output: Circuit Open | GO to Pinpoint Test I |
| B1587:11 | Driver Door Unlock Output: Circuit Short To Ground | GO to Pinpoint Test I |
| B1587:12 | Driver Door Unlock Output: Circuit Short To Battery | GO to Pinpoint Test I |
| B1587:13 | Driver Door Unlock Output: Circuit Open | GO to Pinpoint Test I |
| U0258:87 | Lost Communication With Radio Transceiver: Missing Message | GO to Pinpoint Test Y |
| B1108:24 | Driver door central locking motor: Signal Stuck High | GO to Pinpoint Test I |
| B12B6:24 | Front Lock Motor Common Circuit: Signal Stuck High | GO to Pinpoint Test I |
| B12BA:11 | Lock Status LED - Front: Circuit Short To Ground | GO to Pinpoint Test K |
| B12E1:92 | Front Door Unlock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E1:9E | Front Door Unlock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B12E3:92 | Front Door Lock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E3:9E | Front Door Lock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B147F:07 | Front Door Cinching 1 Motor/Switch: Mechanical Failure | GO to Pinpoint Test G |
| B147F:13 | Front Door Cinching 1 Motor/Switch: Circuit Open | GO to Pinpoint Test G |
| B147F:19 | Front Door Cinching 1 Motor/Switch: Circuit Current Above Threshold | GO to Pinpoint Test G |
| B1516:29 | Passive Lock/Unlock: Signal Invalid | GO to Pinpoint Test V |
| B1519:12 | Exterior Door Unlatch Switch: Circuit Short To Battery | GO to Pinpoint Test E |
| B1519:14 | Exterior Door Unlatch Switch: Circuit Short To Ground or Open | GO to Pinpoint Test E |
| B1519:24 | Exterior Door Unlatch Switch: Signal Stuck High | GO to Pinpoint Test E |
| B1519:92 | Exterior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test E |
| B151A:11 | Interior Door Unlatch Switch: Circuit Short To Ground | GO to Pinpoint Test F |
| B151A:15 | Interior Door Unlatch Switch: Circuit Short To Battery or Open | GO to Pinpoint Test F |
| B151A:23 | Interior Door Unlatch Switch: Signal Stuck Low | GO to Pinpoint Test F |
| B151A:92 | Interior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test F |
| B151C:19 | Interior Unlock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| B151D:19 | Interior Lock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub-Type Information | GO to Pinpoint Test AC |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AD |
| U0151:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AE |
| U0431:00 | Invalid Data Received From Body Control Module "A": No Sub Type Information | GO to Pinpoint Test AN |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U1000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AO |
| U3000:01 | Control Module: General Electrical Failure | GO to Pinpoint Test AP |
| U3000:11 | Control Module: Circuit Short To Ground | GO to Pinpoint Test AP |
| U3000:13 | Control Module: Circuit Open | GO to Pinpoint Test AP |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AP |
| U3000:77 | Control Module: Commanded Position Not Reachable | GO to Pinpoint Test AP |
| U3000:91 | Control Module: Parametric | GO to Pinpoint Test AP |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test AK |
| B1109:24 | Passenger door central locking motor: Signal Stuck High | GO to Pinpoint Test I |
| B12B6:24 | Front Lock Motor Common Circuit: Signal Stuck High | GO to Pinpoint Test I |
| B12BA:11 | Lock Status LED - Front: Circuit Short To Ground | GO to Pinpoint Test K |
| B12E1:92 | Front Door Unlock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E1:9E | Front Door Unlock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B12E3:92 | Front Door Lock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E3:9E | Front Door Lock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B147F:07 | Front Door Cinching 1 Motor/Switch: Mechanical Failure | GO to Pinpoint Test G |
| B147F:13 | Front Door Cinching 1 Motor/Switch: Circuit Open | GO to Pinpoint Test G |
| B147F:19 | Front Door Cinching 1 Motor/Switch: Circuit Current Above Threshold | GO to Pinpoint Test G |
| B1516:29 | Passive Lock/Unlock: Signal Invalid | GO to Pinpoint Test V |
| B1519:12 | Exterior Door Unlatch Switch: Circuit Short To Battery | GO to Pinpoint Test E |
| B1519:14 | Exterior Door Unlatch Switch: Circuit Short To Ground or Open | GO to Pinpoint Test E |
| B1519:24 | Exterior Door Unlatch Switch: Signal Stuck High | GO to Pinpoint Test E |
| B1519:92 | Exterior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test E |
| B151A:11 | Interior Door Unlatch Switch: Circuit Short To Ground | GO to Pinpoint Test F |
| B151A:15 | Interior Door Unlatch Switch: Circuit Short To Battery or Open | GO to Pinpoint Test F |
| B151A:23 | Interior Door Unlatch Switch: Signal Stuck Low | GO to Pinpoint Test F |
| B151A:92 | Interior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test F |
| B151C:19 | Interior Unlock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| B151D:19 | Interior Lock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub-Type Information | GO to Pinpoint Test AC |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AD |
| U0151:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AE |
| U0431:00 | Invalid Data Received From Body Control Module "A": No Sub Type Information | GO to Pinpoint Test AN |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U1000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AO |
| U3000:01 | Control Module: General Electrical Failure | GO to Pinpoint Test AP |
| U3000:11 | Control Module: Circuit Short To Ground | GO to Pinpoint Test AP |
| U3000:13 | Control Module: Circuit Open | GO to Pinpoint Test AP |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AP |
| U3000:77 | Control Module: Commanded Position Not Reachable | GO to Pinpoint Test AP |
| U3000:91 | Control Module: Parametric | GO to Pinpoint Test AP |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test AK |
| B110A:24 | Rear door driver side central locking motor: Signal Stuck High | GO to Pinpoint Test I |
| B1288:24 | Rear Lock Motor Common Circuit: Signal Stuck High | GO to Pinpoint Test I |
| B12BB:11 | Lock Status LED - Rear: Circuit Short To Ground | GO to Pinpoint Test K |
| B12E2:92 | Rear Door Unlock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E2:9E | Rear Door Unlock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B12E4:92 | Rear Door Lock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E4:9E | Rear Door Lock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B1483:07 | Rear Door Cinching Motor/Switch: Mechanical Failure | GO to Pinpoint Test G |
| B1483:13 | Rear Door Cinching Motor/Switch: Circuit Open | GO to Pinpoint Test G |
| B1483:19 | Rear Door Cinching Motor/Switch: Circuit Current Above Threshold | GO to Pinpoint Test G |
| B1516:29 | Passive Lock/Unlock: Signal Invalid | GO to Pinpoint Test V |
| B1519:12 | Exterior Door Unlatch Switch: Circuit Short To Battery | GO to Pinpoint Test E |
| B1519:14 | Exterior Door Unlatch Switch: Circuit Short To Ground or Open | GO to Pinpoint Test E |
| B1519:24 | Exterior Door Unlatch Switch: Signal Stuck High | GO to Pinpoint Test E |
| B1519:92 | Exterior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test E |
| B151A:11 | Interior Door Unlatch Switch: Circuit Short To Ground | GO to Pinpoint Test F |
| B151A:15 | Interior Door Unlatch Switch: Circuit Short To Battery or Open | GO to Pinpoint Test F |
| B151A:23 | Interior Door Unlatch Switch: Signal Stuck Low | GO to Pinpoint Test F |
| B151A:92 | Interior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test F |
| B151C:19 | Interior Unlock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| B151D:19 | Interior Lock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub-Type Information | GO to Pinpoint Test AC |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AD |
| U0151:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AE |
| U0431:00 | Invalid Data Received From Body Control Module "A": No Sub Type Information | GO to Pinpoint Test AN |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U1000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AO |
| U3000:01 | Control Module: General Electrical Failure | GO to Pinpoint Test AP |
| U3000:11 | Control Module: Circuit Short To Ground | GO to Pinpoint Test AP |
| U3000:13 | Control Module: Circuit Open | GO to Pinpoint Test AP |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AP |
| U3000:77 | Control Module: Commanded Position Not Reachable | GO to Pinpoint Test AP |
| U3000:91 | Control Module: Parametric | GO to Pinpoint Test AP |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test AK |
| B110B:24 | Rear door passenger side central locking motor: Signal Stuck High | GO to Pinpoint Test I |
| B1288:24 | Rear Lock Motor Common Circuit: Signal Stuck High | GO to Pinpoint Test I |
| B12BB:11 | Lock Status LED - Rear: Circuit Short To Ground | GO to Pinpoint Test K |
| B12E2:92 | Rear Door Unlock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E2:9E | Rear Door Unlock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B12E4:92 | Rear Door Lock Switch - Interior: Performance or Incorrect Operation | GO to Pinpoint Test J |
| B12E4:9E | Rear Door Lock Switch - Interior: Stuck On | GO to Pinpoint Test J |
| B1483:07 | Rear Door Cinching Motor/Switch: Mechanical Failure | GO to Pinpoint Test G |
| B1483:13 | Rear Door Cinching Motor/Switch: Circuit Open | GO to Pinpoint Test G |
| B1483:19 | Rear Door Cinching Motor/Switch: Circuit Current Above Threshold | GO to Pinpoint Test G |
| B1516:29 | Passive Lock/Unlock: Signal Invalid | GO to Pinpoint Test V |
| B1519:12 | Exterior Door Unlatch Switch: Circuit Short To Battery | GO to Pinpoint Test E |
| B1519:14 | Exterior Door Unlatch Switch: Circuit Short To Ground or Open | GO to Pinpoint Test E |
| B1519:24 | Exterior Door Unlatch Switch: Signal Stuck High | GO to Pinpoint Test E |
| B1519:92 | Exterior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test E |
| B151A:11 | Interior Door Unlatch Switch: Circuit Short To Ground | GO to Pinpoint Test F |
| B151A:15 | Interior Door Unlatch Switch: Circuit Short To Battery or Open | GO to Pinpoint Test F |
| B151A:23 | Interior Door Unlatch Switch: Signal Stuck Low | GO to Pinpoint Test F |
| B151A:92 | Interior Door Unlatch Switch: Performance or Incorrect Operation | GO to Pinpoint Test F |
| B151C:19 | Interior Unlock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| B151D:19 | Interior Lock output: Circuit Current Above Threshold | GO to Pinpoint Test J |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub-Type Information | GO to Pinpoint Test AC |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AD |
| U0151:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AE |
| U0431:00 | Invalid Data Received From Body Control Module "A": No Sub Type Information | GO to Pinpoint Test AN |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U1000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AO |
| U3000:01 | Control Module: General Electrical Failure | GO to Pinpoint Test AP |
| U3000:11 | Control Module: Circuit Short To Ground | GO to Pinpoint Test AP |
| U3000:13 | Control Module: Circuit Open | GO to Pinpoint Test AP |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AP |
| U3000:77 | Control Module: Commanded Position Not Reachable | GO to Pinpoint Test AP |
| U3000:91 | Control Module: Parametric | GO to Pinpoint Test AP |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test AK |
| B108F:23 | Cabin Lock/Unlock Switch: Signal Stuck Low | GO to Pinpoint Test J |
| B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test AB |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AD |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub-Type Information | GO to Pinpoint Test AF |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub-Type Information | GO to Pinpoint Test AG |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub-Type Information | GO to Pinpoint Test AH |
| U0294:00 | Lost Communication With Powertrain Control Monitor Module: No Sub-Type Information | GO to Pinpoint Test AJ |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U0509:00 | Invalid Data Received From "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test AN |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AO |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AP |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AL |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AM |
| P04B5:00 | Fuel Fill Door Stuck Open: No Sub-Type Information | GO to Pinpoint Test Z |
| P04BA:00 | Fuel Fill Door Position Sensor/Switch Circuit High: No Sub-Type Information | GO to Pinpoint Test Z |
| P04C1:00 | Fuel Fill Door Unlock Control Circuit Low: No Sub-Type Information | GO to Pinpoint Test M |
| P04C2:00 | Fuel Fill Door Unlock Control Circuit High: No Sub-Type Information | GO to Pinpoint Test L |
| P04C9:00 | Fuel Fill Door Open Request Sensor/Switch Performance/Stuck Off: No Sub-Type Information | GO to Pinpoint Test L |
| P04CA:00 | Fuel Fill Door Open Request Sensor/Switch Stuck Low: No Sub-Type Information | GO to Pinpoint Test L |
| P04CB:00 | Fuel Fill Door Open Request Sensor/Switch Stuck High: No Sub-Type Information | GO to Pinpoint Test L |
| P04CD:00 | Fuel Fill Door Open Request Sensor/Switch Stuck On: No Sub-Type Information | GO to Pinpoint Test L |
| P1594:00 | Forced Engine Shutdown - Remote Start System Fault, No Unattended Vehicle Timeout: No Fault Type Information | GO to Pinpoint Test AA |
| P1595:00 | Forced Engine Shutdown - Remote Start System Fault, Transmission Range Not In Park Position: No Fault Type Information | GO to Pinpoint Test AA |
| B108F:23 | Cabin Lock/Unlock Switch: Signal Stuck Low | GO to Pinpoint Test J |
| B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test AB |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test AD |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub-Type Information | GO to Pinpoint Test AF |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub-Type Information | GO to Pinpoint Test AG |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub-Type Information | GO to Pinpoint Test AI |
| U0294:00 | Lost Communication With Powertrain Control Monitor Module: No Sub-Type Information | GO to Pinpoint Test AJ |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AO |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AP |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AL |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AM |
| U1A00:00 | Private Communication Network: No Sub Type Information | GO to Pinpoint Test Y |