Pinpoint Test M : The APIM Does Not Respond To The Scan Tool

WARNING: This page is about a different car, the 2015 Lincoln MKS. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery, Mounting and Cables .

M1 CHECK THE APIM VOLTAGE SUPPLY CIRCUIT FOR AN OPEN

Disconnect: APIM C2383 .

Ignition ON.

Measure the voltage between:

Positive Lead		Negative Lead
Pin	Circuit	Pin	Circuit
C2383-1	SBP09 (RD)	-	Ground

Courtesy of FORD MOTOR COMPANY

Is the voltage greater than 11 volts?

Yes	GO to M2.
No	VERIFY the Body Control Module (BCM) fuse 9 (10A) is OK. If OK, REPAIR the circuit in question. If not OK, REFER to the OEM Electrical Wiring Diagram Introduction to identify the possible causes of the circuit short.

M2 CHECK THE APIM GROUND CIRCUITS FOR AN OPEN

Ignition OFF.

Disconnect: Negative Battery Cable.

Measure the resistance between:

Positive Lead		Negative Lead
Pin	Circuit	Pin	Circuit
C2383-37	GD374 (BK/WH)	-	Ground

Courtesy of FORD MOTOR COMPANY

Are the resistances less than 3 ohms?

Yes	GO to M3.
No	REPAIR the circuit in question.

M3 CHECK THE HS-CAN CIRCUITS BETWEEN THE APIM AND THE DLC FOR AN OPEN

Measure the resistance between:

Positive Lead		Negative Lead
Pin	Circuit	Pin	Circuit
C2383-53	VDB04 (WH/BU)	C251-6	VDB04 (WH/BU)
C2383-54	VDB05 (WH)	C251-14	VDB05 (WH)

Courtesy of FORD MOTOR COMPANY

Are the resistances less than 3 ohms?

Yes	GO to M4.
No	REPAIR the circuit in question.

M4 CHECK THE I-CAN CIRCUITS BETWEEN THE APIM AND THE DLC FOR AN OPEN

Measure the resistance between:

Positive Lead		Negative Lead
Pin	Circuit	Pin	Circuit
C2383-19	VDB13 (BU)	C251-1	VDB13 (BU/GY)
C2383-20	VDB14 (VT)	C251-9	VDB14 (VT/GY)

Courtesy of FORD MOTOR COMPANY

Are the resistances less than 3 ohms?

Yes	GO to M5.
No	REPAIR the circuit in question.

M5 CHECK THE MS-CAN CIRCUITS BETWEEN THE APIM AND THE DLC FOR AN OPEN

Measure the resistance between:

Positive Lead		Negative Lead
Pin	Circuit	Pin	Circuit
C2383-16	VDB06 (GY)	C251-3	VDB06 (GY/OG)
C2383-17	VDB07 (VT)	C251-11	VDB07 (VT/OG)

Courtesy of FORD MOTOR COMPANY

Are the resistances less than 3 ohms?

Yes	GO to M6.
No	REPAIR the circuit in question.

M6 CHECK FOR CORRECT APIM OPERATION

Disconnect the APIM connector.

Repair:
- corrosion (replace connector or terminals - clean module pins)
- damaged or bent pins - replace terminals/pins
- pushed-out pins - replace pins as necessary

Connect the APIM connector and make sure it seats correctly.

Operate the system and verify the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, Refer to APIM Hardware Testing .
No	The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.