LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2015 >> MKS Base, AWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seating System >> Disassembly And Assembly >> Seat Backrest Rear >> Disassembly

Seat Backrest Rear: Disassembly

GFD90148Courtesy of FORD MOTOR COMPANY
Item Part Number Description
1 66600 Backrest trim cover
2 14D696 RH and LH backrest heater mats
3 67112 Armrest assembly
4 66800 Backrest foam pad
5 611A08 RH and LH head restraints
6 613D11 LH safety belt guide
7 613A38 Backrest frame
8 610A18 Head restraint guide sleeve (4 required)
9 W505021 Safety belt guide screw (4 required)
10 613D10 RH safety belt guide
11 605C12 Armrest bolt
12 45068 Wave washer
13 14C724 Heated seat module
14 W710752 Scrivet
15 264A50 Armrest grommet
16 19K315 Wire harness
17 613G36 Backrest frame upper retainer cover (3 required)
18 668B10 Door panel
19 W711206 Door panel screw (4 required)
20 - Close-out trim cover (part of 66600)
21 N811404 Pin-type retainers
22 67121 Armrest bracket
23 W504756 Armrest bracket screws
24 67202 Armrest bracket cover
25 W710836 Armrest bracket cover screws
26 13562 Cup holder
27 06024 Armrest cover
28 W790065 Armrest hinge screws (2 required)
NOTE: Always install a new backrest foam pad and backrest heater mats together.

  1. 1.

    Remove the rear seat backrest. For additional information, refer to Seat Backrest - Rear .

  1. 2.

    Remove the 4 head restraint guide sleeves. For additional information, refer to Head Restraint Guide Sleeve .

  1. 3.

    Remove the 4 screws and 2 safety belt guides.

  1. 4.

    Remove the 3 backrest frame upper retainer covers.

  1. 5.

    Remove the close-out trim cover in the following sequence.

    1. 1.

      Release the close out trim cover clips attached to the backrest frame side tubes.

    1. 2.

      From the underneath and at the rear of the backrest, remove 2 pin-type retainers attaching the close-out trim cover to the door panel.

    1. 3.

      Release the close-out trim cover J-clips at the top and bottom.

    1. 4.

      Remove the close-out trim cover.

  1. 6.

    Remove 4 screws and the door panel.

  1. 7.

    Remove 2 screws and the armrest bracket cover.

  1. 8.

    Push the backrest trim cover and foam pad away and remove the armrest bolt and wave washer.
GFD90151Courtesy of FORD MOTOR COMPANY

  1. 9.

    Tilt the armrest and slide the armrest pin out of the backrest frame and grommet.
GFD90152Courtesy of FORD MOTOR COMPANY

  1. 10.

    Remove 2 screws and the armrest bracket.

  1. 11.

    Pull up hard and remove the cup holder from the armrest.

  1. 12.

    Remove 2 screws and the armrest cover.

  1. 13.

    Disconnect the 2 backrest heater mat electrical connectors.

  1. 14.

    Release all backrest trim cover J-clips attached to the backrest frame.

  1. 15.

    At the top rear of the backrest, pull the backrest trim cover over the backrest frame retainers.

  1. 16.

    At the rear of the backrest, remove the hog rings attaching the backrest foam pad to the backrest frame.

  1. 17.

    Pull the backrest frame out of the backrest foam pad.
    • Route the heated seat wire harness and electrical connector through the backrest trim cover.

  1. 18.

    Remove the hog rings and the separate the backrest trim cover from the backrest foam pad.

  1. 19.

    NOTE: Always install a new backrest foam pad and backrest heater mats together.

    If a new backrest foam pad or backrest heater mat is to be installed, obtain a new cushion foam pad and a new LH and RH backrest heater mat.

    • Do not remove the old backrest heater mats from the old backrest foam pad and reuse any of these parts.

  1. 20.

    Disconnect the 2 electrical connectors, remove the scrivet and heated seat module.

  1. 21.

    Separate the pin-type retainers and remove the wire harness from the backrest frame.

  1. 22.

    Remove the armrest grommet.
scientia non olet · About LEMON Manuals