LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 1998 >> Continental >> Repair and Diagnosis >> Body & Frame >> Power Windows >> System Testing >> Test G: Right Rear Window Is Inoperative

Test G: Right Rear Window Is Inoperative

  1. Check Switch Input  - Turn ignition switch to RUN position. Using NGS tester, select and monitor DDM PID RRPW_SW. Press and release driver door window control switch right rear window switch in the UP and DOWN position several times. If PID RRPW_SW values agree with the switch position, go to next step. If PID RRPW_SW values do not agree with the switch position, replace driver door module and retest system operation.
  2. Operate Right Rear Window From Driver Door Switch  - Attempt to operate right rear window from driver door window control switch. If right rear window does not operate properly, go to next step. If right rear window operates properly, go to step 9).
  3. Check Right Rear Window Output From Driver Door Module (DDM)  - Turn ignition off. Disconnect right rear window control switch 4-pin flat connector C809. Turn ignition switch to RUN position. Using a voltmeter, check voltage between ground and right rear window control switch 4-pin flat connector C809 Yellow/Black wire terminal while pressing left front window control switch right rear window to UP position. Check voltage between ground and right rear window control switch 4-pin flat connector C809 Red/Black wire terminal while pressing left front window control switch right rear window to DOWN position. If voltage cycles from zero volts to battery voltage when switches are pressed, go to next step. If voltage does not cycle from zero volts to battery voltage when switches are pressed, go to step 7).
  4. Check Gray/Light Blue Wire For Voltage  - Disconnect right rear window control switch 4-pin square connector C811. Turn ignition switch to RUN position. Using a voltmeter, check voltage between ground and right rear window control switch 4-pin square connector C811 Gray/Light Blue wire terminal. If voltage is more than 10 volts, go to next step. If voltage is 10 volts or less, go to step 10).
  5. Check Black Wire For Open  - Turn ignition off. Using an ohmmeter, check resistance between ground and right rear window control switch 4-pin square connector C811 Black wire terminal. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open in Black wire and retest system operation.
  6. Check Right Rear Window Control Switch  - Check right rear window control switch. See SINGLE SWITCHES  under COMPONENT TESTS. If right rear window control switch is okay, go to step 8). If right rear window control switch is not okay, replace switch and retest system operation.
  7. Check Yellow/Black & Red/Black Wires For Open  - Disconnect DDM 20-pin connector C523 (located in lower front corner of driver door). Using an ohmmeter, check resistance in Yellow/Black wire between DDM 20-pin C523 connector terminal No. 8 and right rear window control switch 4-pin flat connector C809. See Figure . Check resistance in Red/Black wire between DDM 20-pin C523 connector terminal No. 7 and right rear window control switch 4-pin flat connector C809. If either resistance reading is 5 ohms or more, repair open in Yellow/Black and/or Red/Black wire and retest system operation. If both resistance readings are less than 5 ohms, replace driver door module and retest system operation.
  8. Check Brown/Yellow & Brown Wires For Open  - Disconnect right rear window motor connector C810. Using an ohmmeter, check resistance in Brown/Yellow wire between right rear window control switch 4-pin square connector C811 and right rear window motor connector C810. Check resistance in Brown wire between right rear window control switch 4-pin square connector C811 and right rear window motor connector C810. If either resistance reading is 5 ohms or more, repair open in Brown/Yellow and/or Brown wire and retest system operation. If both resistance readings are less than 5 ohms, replace right rear window motor and retest system operation.
  9. Check Red/Light Blue Wire For Voltage  - Disconnect right rear window control switch 4-pin flat connector C809. Turn ignition switch to RUN position. Using a voltmeter, check voltage between ground and right rear window control switch 4-pin flat connector C809 Red/Light Blue wire terminal. If voltage is more than 10 volts, replace right rear window control switch and retest system operation. If voltage is 10 volts or less, repair open in Red/Light Blue wire and retest system operation.
  10. Check Fuse  - Ensure transmission is in Park. Turn ignition off. Remove and check condition of engine compartment power distribution box mini-fuse No. 3 (30-amp). If fuse is okay, go to next step. If fuse is open, replace fuse and retest system operation. If new fuse opens again, go to step 12).
  11. Check For Voltage To Fuse  - Using a voltmeter, check voltage between ground and engine compartment power distribution box mini-fuse No. 3 (30-amp) input cavity. If voltage is more than 10 volts, repair open in Gray/Light Blue wire and retest system operation. If voltage is 10 volts or less, replace engine compartment power distribution box and retest system operation.
  12. Check Gray/Light Blue Wire For Short To Ground  - Disconnect right rear window control switch 4-pin square connector C811. Using an ohmmeter, check resistance between ground and engine compartment power distribution box mini-fuse No. 3 (30-amp) output cavity. If resistance is more than 10 k/ohms, go to next step. If resistance is 10 k/ohms or less, repair short to ground in Gray/Light Blue wire and retest system operation.
  13. Check Right Rear Window Control Switch  - Check right rear window control switch. See SINGLE SWITCHES  under COMPONENT TESTS. If right rear window control switch is okay, go to next step. If right rear window control switch is not okay, replace switch and retest system operation.
  14. Check Yellow/Black & Red/Black Wire For Voltage  - Disconnect DDM 20-pin connector C523 (located in lower front corner of driver door). Using a voltmeter, check voltage between ground and right rear window control switch 4-pin flat connector C809 Yellow/Black wire terminal. Check voltage between ground and right rear window control switch 4-pin flat connector C809 Red/Black wire terminal. If either voltage reading is more than 10 volts, repair Yellow/Black and/or Red/Black wire for short to voltage and retest system operation. If both voltage readings are 10 volts or less, go to next step.
  15. Check Yellow/Black & Red/Black Wire For Short To Ground  - Using an ohmmeter, check resistance between ground and right rear window control switch 4-pin flat connector C809 Yellow/Black wire terminal. Check resistance between ground and right rear window control switch 4-pin flat connector C809 Red/Black wire terminal. If both resistance readings are more than 10 k/ohms, go to next step. If either resistance reading is 10 k/ohms or less, repair short to ground in Yellow/Black and/or Red/Black wire and retest system operation.
  16. Check Brown & Brown/Yellow Wire For Short To Voltage  - Reconnect DDM 20-pin connector C523. Disconnect right rear window control switch 4-pin square connector C811. Using a voltmeter, check voltage between ground and right rear window control switch 4-pin square connector C811 Brown wire terminal. Check voltage between ground and right rear window control switch 4-pin square connector C811 Brown/Yellow wire terminal. If both voltage readings are 10 volts or less, go to next step. If either voltage reading is more than 10 volts, repair short to voltage in Brown and/or Brown/Yellow wire and retest system operation.
  17. Check Brown & Brown/Yellow Wire For Short To Ground  - Disconnect right rear window motor connector C810. Using an ohmmeter, check resistance between ground and right rear window control switch 4-pin square connector C811 Brown wire terminal. Check resistance between ground and right rear window control switch 4-pin square connector C811 Brown/Yellow wire terminal. If both resistance readings are more than 10 k/ohms, replace right rear window motor and retest system operation. If either resistance reading is 10 k/ohms or less, repair short to ground in Brown and/or Brown/Yellow wire and retest system operation.
scientia non olet · About LEMON Manuals