Fail-Safe Chart [10/2015 - 07/2020]

If any of the following DTCs are stored, the ECM assembly enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC Code	Component	Fail-Safe Operation	Fail-Safe Deactivation Condition
P0031 P0032 P0051 P0052 P101D P103D	Air fuel ratio sensor heater	The ECM assembly turns off the air fuel ratio sensor heater.	Power switch off
P0037 P0038 P0057 P0058 P102D P105D	Heated oxygen sensor heater	The ECM assembly turns off the heated oxygen sensor heater.	Power switch off
P0087 P0088	Fuel pump assembly (for high pressure side)	Stop the fuel pump assembly (for high pressure side). Limit the engine speed to 2000 rpm or less.	Pass condition detected
P0102 P0103	Mass air flow meter sub-assembly	The ECM assembly calculates ignition timing according to the engine speed and throttle valve position.	Pass condition detected
P0106 P0107 P0108	Manifold absolute pressure sensor	The ECM assembly turns off EGR valve operate.	Pass condition detected
P0112 P0113	Intake air temperature sensor	The ECM assembly estimates the intake air temperature to be 20°C (68°F).	Pass condition detected
P0115 P0117 P0118	Engine coolant temperature sensor	The ECM assembly estimates the engine coolant temperature to be 80°C (176°F).	Pass condition detected
P0120 P0121 P0122 P0123 P0220 P0222 P0223 P0604 P0606 P060A P060B P060E P0657 P2102 P2103 P2111 P2112 P2118 P2119 P2135	Electronic throttle control system	The ECM assembly cuts off throttle actuator current and the throttle valve is returned to a 7° throttle position by the return spring. The ECM assembly stops the engine and the vehicle can be driven using solely the hybrid system.*	Pass condition detected and then power switch turned off
P0192 P0193 P1235	Fuel pressure sensor	Stop the fuel pump assembly (for high pressure side). Limit the engine speed to 2000 rpm or less. Fuel pressure is set to 200 kPa.	Pass condition detected and then power switch turned off
P0201 P0202 P0203 P0204 P0205 P0206 P062D	Injector driver (EDU)	The ECM assembly performs fuel-cut when the engine speed is 1000 rpm or more. Stop fuel injection for an abnormal cylinder and related other cylinders.	Pass condition detected and then power switch turned off
P0327 P0328 P0332 P0333	Knock control sensor	The ECM assembly sets the ignition timing to maximum retard.	Power switch off
P0351 P0352 P0353 P0354 P0355 P0356	Ignition coil assembly	The ECM assembly cuts the fuel injection.	Pass condition detected
P0401 P0403	EGR valve assembly	ECM assembly assumes that EGR valve assembly is closed, so that ignition timing controlled to a safe valve.	Pass condition detected and then power switch turned off
P107C P107D	Fuel pressure sensor (for low pressure side)	Fuel pump (for low pressure side) control is maintained.	Pass condition detected and then power switch turned off
P1276 P1277 P1278 P1279 P127A P127B	Fuel injector assembly (for port injection)	The ECM assembly performs fuel-cut when the engine speed is 2000 rpm or more. Fuel cut of malfunction cylinder.	Pass condition detected and then power switch turned off
P2237 P2238 P2239 P2240 P2241 P2242 P2252 P2253 P2255 P2256	Air fuel ratio sensor	Air fuel ratio feedback control is stopped. Current to the air fuel ratio sensor heater is cut.	Pass condition detected and then power switch turned off

HINT:

*: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly.