How To Proceed With Troubleshooting [08/2015 - 08/2019]: Procedure

Result

Result: 

NEXT 

See step  2

Standard voltage

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding.

HINT: 

A simple method to determine whether the battery is depleted is to operate the horn.

Result

Result: 

NEXT 

See step  3

HINT: 

If the engine switch cannot be turned on (IG), communication with the Techstream can be confirmed by connecting the Techstream to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins.

Result

Result: 

NEXT 

See step  4

1. Use the Techstream to check if the CAN communication system is functioning normally.

   Result

   Result	Proceed to
   CAN DTC is not output	A
   CAN DTC is output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - 08/2019] 

Result: 

A 

See step  5

1. Use the Techstream to check if the LIN communication system is functioning normally.

   Result

   Result	Proceed to
   LIN DTC is not output	A
   LIN DTC is output	B

Result: 

B 

GO TO LIN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - 08/2019] 

Result: 

A 

See step  6

1. Check for DTCs and make a note of any codes that are output.

   Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] 

2. Based on the DTCs output above, proceed to each diagnostic procedure.

   Result

   Result	Proceed to
   DTC is not output	A
   SFI system DTC is output	B
   Steering lock system DTC is output	C
   Engine immobiliser system DTC is output	D

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2016]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - 08/2017]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2017 - 08/2019] 

Result: 

C 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2019] 

Result: 

D 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2019]  

Result: 

A 

See step  7

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [08/2015 - 08/2019] 

   Result

   Result	Proceed to
   Fault is not listed in problem symptoms table	A
   Fault is listed in problem symptoms table	B

Result: 

B 

See step  9

Result: 

A 

See step  8

1. Check Data List / Active Test.

   Refer to DATA LIST / ACTIVE TEST [08/2015 - 08/2019] 

2. Check Terminals of ECU.

   Refer to TERMINALS OF ECU [08/2015 - 08/2019] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

Result

Result: 

NEXT 

See step  10

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] 

2. Check for DTCs.

   Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] 

   HINT: 

   Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2019] 

   Result

   Result	Proceed to
   DTC is not output	A
   Engine immobiliser system DTC is output	B

Result: 

A 

END 

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2019]