New Key cannot be Registered (Owner Key) [10/2023 - ]: Procedure

1. Read the Data List according to the display on the GTS.

   Body Electrical > Smart Access > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Owner's Digital Key Registration Status	Registration status of owner key	Not Registered or Registered	Not Registered: Not registered Registered: Registered	-

   Body Electrical > Smart Access > Data List 

   Tester Display
   Owner's Digital Key Registration Status

   Result

   Result	Proceed to
   Owner key is registered	A
   Owner key is not registered	B

Result: 

B 

See step  3

Result: 

A 

See step  2

1. Clear all registered digital keys.

   Refer to REGISTRATION [10/2023 - ]

   OK

   All digital keys can be cleared

   Result

   Proceed to
   NEXT

Result: 

NEXT 

END (PERFORM OWNER KEY REGISTRATION) 

1. Using the digital key application, perform new registration of the owner key from inside the vehicle.
   NOTE:

   • Make sure there is no electronic device that outputs high-voltage or noise inside or around the vehicle.
   • Make sure that the digital key is not covered by or touching a metal object.

   HINT: 

   Refer to the digital key application.

   OK

   Registration can be performed normally

   Result

   Proceed to
   OK
   NG

Result: 

OK 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2023 - ] 

Result: 

NG 

See step  4

1. Perform cause analysis in the following tables.

   Body Electrical > Smart Access > Utility 

   Tester Display
   Vehicle Control History (RoB)

   Result

   Main Category	Sub Category	Memorized Conditions	Proceed to
   Digital Key (Inactive)	Digital key Code Confirmation Failed (No Response from Digital key ECU)	Registration could not be performed as the certification ECU (smart key ECU assembly) did not receive a response from the digital key ECU assembly	A
   	Owner Digital Key Registration Failure	The owner key could not be registered	B
   	ECU Code Confirmation Failed (D Code Certification Failed)	Registration could not be performed as the D code* of the certification ECU (smart key ECU assembly) and digital key ECU assembly did not match.	C
   The above vehicle control history (RoB) is not stored			D

   1. *: Verification code between the certification ECU (smart key ECU assembly) and digital key ECU assembly

Result: 

B 

REPLACE DIGITAL KEY ECU ASSEMBLY. Refer to  REMOVAL [10/2023 - ] 

Result: 

C 

See step  6

Result: 

D 

See step  9

Result: 

A 

See step  5

1. Check the smart access system with push-button start (for Start Function).

   Refer to OPERATION CHECK [10/2023 - ]

2. Check that electrical key transmitter sub-assembly registration can be performed normally.

   HINT: 

   Refer to REGISTRATION [10/2023 - ]

   OK

   Smart access system with push-button start (for start function) is normally and electrical key transmitter sub-assembly can be registered

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [10/2023 - ] 

Result: 

NG 

GO TO SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function) (HOW TO PROCEED WITH TROUBLESHOOTING). Refer to  REGISTRATION [10/2023 - ] 

1. Replace the digital key ECU assembly with a new one.

   HINT: 

   Refer to REMOVAL [10/2023 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  7

1. Register the digital key code to the digital key ECU assembly.

   HINT: 

   Refer to REGISTRATION [10/2023 - ]

   OK

   Registration can be performed normally

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [10/2023 - ] 

Result: 

OK 

See step  8

1. Using the digital key application, perform new registration of the owner key from inside the vehicle.
   NOTE:

   • Make sure there is no electronic device that outputs high-voltage or noise inside or around the vehicle.
   • Make sure that the digital key is not covered by or touching a metal object.

   HINT: 

   Refer to the digital key application.

   OK

   Registration can be performed normally

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (DIGITAL KEY ECU ASSEMBLY WAS DEFECTIVE) 

Result: 

NG 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [10/2023 - ] 

1. Using the digital key application of another mobile device, perform new registration of the owner key from inside the vehicle.
   NOTE:

   • Make sure there is no electronic device that outputs high-voltage or noise inside or around the vehicle.
   • Make sure that the digital key is not covered by or touching a metal object.

   HINT: 

   Refer to the digital key application.

   OK

   Registration can be performed normally

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (PERFORM TROUBLESHOOTING ON ORIGINAL DIGITAL KEY) 

Result: 

NG 

See step  10

1. Refer to Precautions for Inspection or Registration, and check for any causes of malfunctions other than vehicle settings or vehicle components.

   Refer to PRECAUTION [10/2023 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  11

1. Using the digital key application, perform new registration of the owner key from inside the vehicle.
   NOTE:

   • Make sure there is no electronic device that outputs high-voltage or noise inside or around the vehicle.
   • Make sure that the digital key is not covered by or touching a metal object.

   HINT: 

   Refer to the digital key application.

   OK

   Registration can be performed normally

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (CAUSE OF MALFUNCTION NOT RELATED TO VEHICLE SETTINGS OR VEHICLE COMPONENTS) 

Result: 

NG 

REPLACE DIGITAL KEY ECU ASSEMBLY. Refer to  REMOVAL [10/2023 - ]