LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> GS F >> Repair and Diagnosis (Single Page) >> Body & Frame >> Door Locks >> Smart Access System (Keyless Start) (Diagnostics) (Introduction) >> SMART ACCESS SYSTEM WITH PUSH-BUTTON START (For Start Function) >> DTC Check / Clear [10/2015 - ] >> DTC Check / Clear [10/2015 - ]

DTC Check / Clear [10/2015 - ]

NOTE:

When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

  1. CHECK FOR DTC (POWER SOURCE CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > Power Source Control > Trouble Codes 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  2. CHECK FOR DTC (STARTING CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Starting Control / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > Starting Control > Trouble Codes 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  3. CHECK FOR DTC (Smart Access) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Smart Access / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > Smart Access > Trouble Codes 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  4. CLEAR DTC (POWER SOURCE CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.
    5. Clear the DTCs by following the directions on the Techstream display.

      Body Electrical > Power Source Control > Clear DTCs 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  5. CLEAR DTC (STARTING CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Starting Control / Trouble Codes.
    5. Clear the DTCs by following the directions on the Techstream display.

      Body Electrical > Starting Control > Clear DTCs 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  6. CLEAR DTC (Smart Access) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Smart Access / Trouble Codes.
    5. Clear the DTCs by following the directions on the Techstream display.

      Body Electrical > Smart Access > Clear DTCs 

      HINT: 

      Refer to the Techstream operator's manual for further details.

scientia non olet · About LEMON Manuals