DTC P0505: Idle Control System [10/2015 - 07/2020]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
5. Read the DTCs.

   Powertrain > Engine and ECT > Trouble Codes 

   Result

   Result	Proceed to
   DTC P0505 is output	A
   DTC P0505 and other DTCs are output	B

   HINT: 

   If any DTCs other than P0505 are output, troubleshoot those DTCs first.

Result: 

B 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2015 - 08/2016]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - 12/2017]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [12/2017 - 03/2018]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [03/2018 - 08/2018]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2019 - 07/2020] 

Result: 

A 

See step  2

1. Check the PCV hose connections.

   Refer to COMPONENTS [10/2015 - ]

   OK

   PCV valve and hose are connected correctly and are not damaged.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE PCV HOSE 

Result: 

OK 

See step  3

1. Check the intake system for vacuum leaks.

   Refer to PROCEDURE - Step 1 [10/2015 - 12/2017] , or refer to PROCEDURE - Step 1 [12/2017 - ]

   OK

   No leaks from the intake system.

   HINT: 

   Perform "Inspection After Repair" after repairing or replacing the intake system.

   Refer to INITIALIZATION [10/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE INTAKE SYSTEM 

Result: 

OK 

See step  4

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Put the engine in inspection mode (maintenance mode).

   Powertrain > Hybrid Control > Utility 

   Tester Display
   Inspection Mode

5. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

   HINT: 

   The A/C switch and all accessory switches should be off.

6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / MAP and Throttle Idle Position.

   Powertrain > Engine and ECT > Active Test 

   Active Test Display
   Control the EGR Step Position

   Data List Display
   MAP
   Throttle Idle Position

7. Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

   HINT: 

   • Do not leave the EGR valve open for 10 seconds or more during the Active Test.
   • Be sure to return the EGR valve to step 0 when the Active Test is completed.
   • Do not open the EGR valve 30 steps or more during the Active Test.

   OK

   MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.

   Standard

   -	EGR Step Position (Active Test)
   	0 Steps	0 to 30 Steps
   MAP (Data List)	(EGR valve is fully closed)	MAP value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed

   HINT: 

   • While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
   • Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  6

Result: 

NG 

See step  5

1. Remove the EGR valve assembly.

   Refer to REMOVAL [10/2015 - ]

2. Check if the EGR valve is stuck open.

   OK

   EGR valve is tightly closed.

   HINT: 

   Perform "Inspection After Repair" after replacing the EGR valve assembly.

   Refer to INITIALIZATION [10/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE EGR VALVE ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

Result: 

OK 

See step  6

1. Check the throttle body with motor assembly condition.

   OK

   Throttle valve is not contaminated with foreign matter and moves smoothly.

   HINT: 

   Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

   Refer to INITIALIZATION [10/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

Result: 

OK 

See step  7

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Clear the DTCs.

   Powertrain > Engine and ECT > Clear DTCs 

5. Turn the power switch off and wait for at least 30 seconds.
6. Turn the power switch on (IG).
7. Turn the Techstream on.
8. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
10. Read the pending DTCs.

    Powertrain > Engine and ECT > Trouble Codes 

    Result

    Result	Proceed to
    DTC P0505 is output	A
    DTCs are not output	B

Result: 

A 

REPLACE ECM ASSEMBLY. Refer to  REMOVAL [10/2015 - 08/2016]  , or refer to  REMOVAL [08/2016 - 03/2018]  , or refer to  REMOVAL [03/2018 - 08/2019]  , or refer to  REMOVAL [08/2019 - ] 

Result: 

B 

END