Outside Handle Foot Light Circuit [10/2015 - 08/2019]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Active Test.
5. Perform the Active Test according to the display on the Techstream.

   Body Electrical > Main Body > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Exterior Light	Outside handle foot lights	ON/OFF	-

   Body Electrical > Main Body > Active Test 

   Tester Display
   Exterior Light

   OK

   Outside handle foot lights illuminate.

   Result

   Result	Proceed to
   OK	A
   NG (for Front Side)	B
   NG (for Rear Side)	C

Result: 

A 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [10/2015 - 12/2017]  , or refer to  PROBLEM SYMPTOMS TABLE [12/2017 - 03/2018]  , or refer to  PROBLEM SYMPTOMS TABLE [03/2018 - 08/2019] 

Result: 

C 

See step  6

Result: 

B 

See step  2

1. Disconnect the N11 front door outside handle assembly LH connector.
2. Measure the voltage according to the value (s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   N11-1 (OLP) - Body ground	Illumination conditions of outside handle foot lights met*	11 to 14 V

   1. *: Refer to System Description for the illumination conditions of the outside handle foot lights.

      Refer to SYSTEM DESCRIPTION [10/2015 - 08/2019]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  3

1. Remove the front door outside handle assembly LH.

   Refer to DISASSEMBLY [10/2015 - 08/2016] , or refer to DISASSEMBLY [08/2016 - 03/2018] , or refer to DISASSEMBLY [03/2018 - 08/2019]

2. Inspect the front door outside handle assembly LH.

   Refer to INSPECTION [10/2015 - ]

   OK

   Outside handle foot light illuminates.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH. Refer to  DISASSEMBLY [10/2015 - 08/2016]  , or refer to  DISASSEMBLY [08/2016 - 03/2018]  , or refer to  DISASSEMBLY [03/2018 - 08/2019] 

Result: 

OK 

See step  4

1. Remove the front door outside handle assembly RH.

   Refer to DISASSEMBLY [10/2015 - 08/2016] , or refer to DISASSEMBLY [08/2016 - 03/2018] , or refer to DISASSEMBLY [03/2018 - 08/2019]

2. Inspect the front door outside handle assembly RH.

   Refer to INSPECTION [10/2015 - ]

   OK

   Outside handle foot light illuminates.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH. Refer to  DISASSEMBLY [10/2015 - 08/2016]  , or refer to  DISASSEMBLY [08/2016 - 03/2018]  , or refer to  DISASSEMBLY [03/2018 - 08/2019] 

Result: 

OK 

See step  5

1. Measure the resistance according to the value (s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   M11-3 (GND) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH - FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH) 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Disconnect the P4 rear door outside handle assembly LH connector.
2. Measure the voltage according to the value (s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   P4-1 (OLP) - Body ground	Illumination conditions of outside handle foot lights met*	11 to 14 V

   1. *: Refer to System Description for the illumination conditions of the outside handle foot lights.

      Refer to SYSTEM DESCRIPTION [10/2015 - 08/2019]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  7

1. Remove the rear door outside handle assembly LH.

   Refer to DISASSEMBLY [10/2015 - 08/2016] , or refer to DISASSEMBLY [08/2016 - 03/2018] , or refer to DISASSEMBLY [03/2018 - 08/2019]

2. Inspect the rear door outside handle assembly LH.

   Refer to INSPECTION [10/2015 - ]

   OK

   Outside handle foot light illuminates.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH. Refer to  DISASSEMBLY [10/2015 - 08/2016]  , or refer to  DISASSEMBLY [08/2016 - 03/2018]  , or refer to  DISASSEMBLY [03/2018 - 08/2019] 

Result: 

OK 

See step  8

1. Remove the rear door outside handle assembly RH.

   Refer to DISASSEMBLY [10/2015 - 08/2016] , or refer to DISASSEMBLY [08/2016 - 03/2018] , or refer to DISASSEMBLY [03/2018 - 08/2019]

2. Inspect the rear door outside handle assembly RH.

   Refer to INSPECTION [10/2015 - ]

   OK

   Outside handle foot light illuminates.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY RH. Refer to  DISASSEMBLY [10/2015 - 08/2016]  , or refer to  DISASSEMBLY [08/2016 - 03/2018]  , or refer to  DISASSEMBLY [03/2018 - 08/2019] 

Result: 

OK 

See step  9

1. Measure the resistance according to the value (s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   O4-3 (GND) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR DOOR OUTSIDE HANDLE ASSEMBLY LH - REAR DOOR OUTSIDE HANDLE ASSEMBLY RH) 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR