LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 350 Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 11 (Lighting System (Ext) - Diagnostic Codes & Circuit Tests) >> Lighting System >> DTC B2414: Steering Position Sensor [10/2018 - ] >> Procedure

DTC B2414: Steering Position Sensor [10/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2024 Lexus RC 350, 2024 Lexus RC 300, 2023 Lexus RC 350, 2023 Lexus RC 300, and 2022 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  2

  2. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      OK

      DTC B2414 is not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - 11/2019]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2019 - 09/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2020 - 10/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - ] 

    Result: 

    NG 

    See step  3

  3. REPLACE STEERING SENSOR 
    1. Replace the steering sensor with a new or known good one.

      Refer to REMOVAL [09/2014 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  4

  4. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      OK

      DTC B2414 is not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END (STEERING SENSOR WAS DEFECTIVE) 

    Result: 

    NG 

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [10/2018 - ] 

scientia non olet · About LEMON Manuals