LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 350 Base, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Infotainment >> Navigation System - Diagnostic Codes (1 Of 2) >> Navigation System >> DTC B15C3: Speaker Output Short [09/2014 - 11/2017] >> Procedure

DTC B15C3: Speaker Output Short [09/2014 - 11/2017]: Procedure

  1. CHECK MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for 10 Speakers (w/ Manual (SOS) Switch) A
      for 10 Speakers (w/o Manual (SOS) Switch) B
      for 17 Speakers (w/ Manual (SOS) Switch) C
      for 17 Speakers (w/o Manual (SOS) Switch) D

    Result: 

    B 

    See step  5

    Result: 

    C 

    See step  12

    Result: 

    D 

    See step  16

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) 
    1. Disconnect the T20 stereo component amplifier assembly connector.
    2. Disconnect the O65 DCM (telematics transceiver) connector.
    3. Disconnect the O55 front No. 2 speaker assembly LH connector.
    4. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.
    5. Disconnect the O56 front No. 3 speaker assembly connector.
    6. Disconnect the T25 and U35 rear speaker assembly connectors.
    7. Disconnect the T24 rear No. 3 speaker assembly connector.
    8. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) 
    1. Disconnect the O65 DCM (telematics transceiver) connector.
    2. Disconnect the O54 front No. 2 speaker assembly RH connector.
    3. Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O65-5 (SPO+) - Body ground Always 10 kΩ or higher
      O65-6 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [09/2014 - 11/2017]

    2. Measure the resistance according to the value(s) in the table below.
      GTY450683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  6

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [09/2014 - 11/2017] 

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) 
    1. Disconnect the T20 stereo component amplifier assembly connector.
    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.
    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.
    4. Disconnect the O56 front No. 3 speaker assembly connector.
    5. Disconnect the T25 and U35 rear speaker assembly connectors.
    6. Disconnect the T24 rear No. 3 speaker assembly connector.
    7. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY459808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front No. 2 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 3.2 to 4.8 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  7

  7. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Refer to REMOVAL [09/2014 - ]

    2. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [09/2014 - 11/2017]

      Body Electrical > Navigation System > Clear DTCs 

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  8

  8. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY462783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front No. 1 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  9

  9. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY459808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front No. 3 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 4.0 to 6.0 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  10

  10. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY462783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  11

  11. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 
    1. Remove the rear No. 3 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY462783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear No. 3 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 2.0 to 3.0 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

  12. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) 
    1. Disconnect the T20 stereo component amplifier assembly connector.
    2. Disconnect the O65 DCM (telematics transceiver) connector.
    3. Disconnect the O55 front No. 2 speaker assembly LH connector.
    4. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.
    5. Disconnect the O56 front No. 3 speaker assembly connector.
    6. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.
    7. Disconnect the T23 and U34 rear header speaker assembly connectors.
    8. Disconnect the T24 rear No. 3 speaker assembly connector.
    9. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  13

  13. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) 
    1. Disconnect the O65 DCM (telematics transceiver) connector.
    2. Disconnect the O54 front No. 2 speaker assembly RH connector.
    3. Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O65-5 (SPO+) - Body ground Always 10 kΩ or higher
      O65-6 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the T25 and U35 rear speaker assembly connectors.
    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.
    3. Measure the resistance between each of the rear No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T26-4 (+) - Body ground Always 10 kΩ or higher
      T26-2 (-) - Body ground Always 10 kΩ or higher
      U36-4 (+) - Body ground Always 10 kΩ or higher
      U36-2 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  15

  15. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [09/2014 - 11/2017]

    2. Measure the resistance according to the value(s) in the table below.
      GTY450683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  18

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [09/2014 - 11/2017] 

  16. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) 
    1. Disconnect the T20 stereo component amplifier assembly connector.
    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.
    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.
    4. Disconnect the O56 front No. 3 speaker assembly connector.
    5. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.
    6. Disconnect the T23 and U34 rear header speaker assembly connectors.
    7. Disconnect the T24 rear No. 3 speaker assembly connector.
    8. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the T25 and U35 rear speaker assembly connectors.
    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.
    3. Measure the resistance between each of the rear No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T26-4 (+) - Body ground Always 10 kΩ or higher
      T26-2 (-) - Body ground Always 10 kΩ or higher
      U36-4 (+) - Body ground Always 10 kΩ or higher
      U36-2 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  18

  18. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY459808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front No. 2 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 6.5 to 9.7 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  19

  19. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Refer to REMOVAL [09/2014 - ]

    2. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [09/2014 - 11/2017]

      Body Electrical > Navigation System > Clear DTCs 

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  20

  20. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY462783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front No. 1 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 4.3 to 6.3 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  21

  21. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY459808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front No. 3 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 6.5 to 9.7 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  22

  22. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Replace the front No. 3 speaker assembly with a new or known good one.

      Refer to REMOVAL [09/2014 - ]

    2. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [09/2014 - 11/2017]

      Body Electrical > Navigation System > Clear DTCs 

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  23

  23. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY462783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 3.6 to 5.6 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  24

  24. INSPECT REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY466063Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear No. 2 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (+TW) - 1 (-TW) Always 10 kΩ or higher
      3 (+TW) - 4 (+) Always Below 1 Ω
      1 (-TW) - 2 (-) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  25

  25. REPLACE REAR NO. 2 SPEAKER ASSEMBLY 
    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Refer to REMOVAL [09/2014 - ]

    2. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [09/2014 - 11/2017]

      Body Electrical > Navigation System > Clear DTCs 

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  26

  26. INSPECT REAR HEADER SPEAKER ASSEMBLY 
    1. Remove the rear header speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY467376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Header Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 6.5 to 9.7 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR HEADER SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    OK 

    See step  27

  27. REPLACE REAR HEADER SPEAKER ASSEMBLY 
    1. Replace the rear header speaker assembly with a new or known good one.

      Refer to REMOVAL [09/2014 - ]

    2. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [09/2014 - 11/2017]

      Body Electrical > Navigation System > Clear DTCs 

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the rear header speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left rear header speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  28

  28. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 
    1. Remove the rear No. 3 speaker assembly.

      Refer to REMOVAL [09/2014 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY462783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear No. 3 Speaker Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 4.8 to 6.8 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2014 - ] 

scientia non olet · About LEMON Manuals