Data List / Active Test [08/2015 - 08/2019]
- DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / (desired system) / Data List.
- According to the display on the Techstream, read the Data List.PRE-COLLISION
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Driver Buckle SW Driver side buckle switch status of driver side seat / UNKNOW, UNSET, SET or NG UNKNOW: Driver side buckle switch status unknown
UNSET: Driver side seat belt unfastened
SET: Driver side seat belt fastened
NG: Indeterminate data- Passenger Buckle SW Front passenger side buckle switch status of passenger side seat / UNKNOW, UNSET, SET or NG UNKNOW: Passenger side buckle switch status unknown
UNSET: Passenger side seat belt unfastened
SET: Passenger side seat belt fastened
NG: Indeterminate data- Driver Belt Control Seat belt control status of driver side seat / STOP, ON or ERROR STOP: Control stopped
ON: Controlled
ERROR: Indeterminate dataThe seat belt (driver side) is fastened. Passenger Belt Control Seat belt control status of passenger side seat / STOP, ON or ERROR STOP: Control stopped
ON: Controlled
ERROR: Indeterminate dataThe seat belt (passenger side) is fastened. Number of Trouble Codes Number of stored trouble codes / Min.: 0, Max.: 255 Number of stored DTCs displayed - PRE-COLLISION 2Tester Display Measurement Item/Range Normal Condition Diagnostic Note Wiper Information Wiper information signal / Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi The respective operational status displayed - Head Light Information Headlight operational signal / Unknown, Fail, Prohibited, Direct, Hi, Passing, Fail The respective operational status displayed - Head Light Headlight switch position signal / ON or OFF ON: Headlight switch on
OFF: Headlight switch off- Head Light (High Beam) High beam headlight switch position signal / ON or OFF ON: Headlight dimmer switch Hi
OFF: Headlight dimmer switch except Hi- Pre-Collision Brake OFF Switch Pre-collision brake cancel switch assembly signal / ON or OFF ON: Pre-collision brake cancel switch assembly on
OFF: Pre-collision brake cancel switch assembly off- Pre-Collision System Pre-collision system signal / Valid or Inval Valid: Pre-collision system operation possible
Inval: Pre-collision system operation not possible- DCam Indicator Driver camera indicator display request signal / ON or OFF ON: Driver camera indicator display requested
OFF: Driver camera indicator display not requested- PCS Indicator PCS indicator light signal / ON or OFF ON: PCS indicator light blinks
OFF: PCS indicator light off- PCS Disabled Indicator PCS indicator light signal / ON or OFF ON: PCS indicator light on
OFF: PCS indicator light off- Pre-Collision Safety Warning Ind PCS indicator light signal / ON or OFF ON: PCS indicator light blinks
OFF: PCS indicator light off- Pre-Collision Safety Brake Ind PCS indicator light signal / ON or OFF ON: PCS indicator light blinks
OFF: PCS indicator light off- Pre-Collision Safety Warning Buz Pre-collision warning buzzer signal / Valid or Inval Valid: Pre-collision warning buzzer operation possible
Inval: Pre-collision warning buzzer operation not possible- Pre-Collision Brake Pre-collision brake signal / Valid or Inval Valid: Pre-collision braking operation possible
Inval: Pre-collision braking operation not possible- Front Radar PSB Pre-collision seat belt signal / ON or OFF ON: Pre-collision seat belt operating
OFF: Pre-collision seat belt not operating- PBA Start Pre-collision brake assist operation signal / ON or OFF ON: Pre-collision brake assist brake operating
OFF: Pre-collision brake assist brake not operating- Warning Brake Warning brake control signal / ON or OFF ON: Warning brake control operating
OFF: Warning brake control not operating- Brake Assist Standby Brake assist standby signal / ON or OFF ON: Brake assist in standby mode
OFF: Brake assist not in standby mode- Pre-Collision Brake Control Pre-collision brake control signal / ON or OFF ON: Pre-collision braking control operating
OFF: Pre-collision braking control not operating- AVS Start AVS control activation status / ON or OFF ON: AVS control activated
OFF: AVS control not activated- Face Direction Driver monitor camera detection information / Left or Right Right: Facing right
Left: Facing left- Face Orientation Angle Horizontal angle of driver's face / Min.: 0 deg, Max.: 63 deg Indicates direction of driver's face in range between 0 and 63 degrees - Driver Monitor Voltage Driver monitor camera voltage status / Normal or Low Normal: Normal voltage
Low: Low voltage- CCS Cancel Dynamic radar cruise control system cancel signal / ON or OFF ON: Dynamic radar cruise control system canceled
OFF: Dynamic radar cruise control system operating- Front Radar-Dirt History Millimeter wave radar sensor assembly dirty signal / ON or OFF ON: Millimeter wave radar sensor assembly dirty
OFF: Millimeter wave radar sensor assembly not dirty- Front Radar-Environment Hist Millimeter wave radar sensor assembly environment signal / Good or Bad Good: Millimeter wave radar sensor assembly environment good
Bad: Millimeter wave radar sensor assembly environment bad- Recognition Camera Image History Lane recognition camera sensor assembly malfunction history / ON or OFF ON: History of lane recognition camera sensor assembly malfunction
OFF: No history of lane recognition camera sensor assembly malfunction- Driver Monitor Image History Driver monitor ECU malfunction history / ON or OFF ON: History of driver monitor ECU malfunction
OFF: No history of driver monitor ECU malfunction- Recog ECU H Temp Stop Lane recognition camera sensor assembly high temperature stop status / Normal or Stop Normal: System normal
Stop: Lane-recognition ECU stopped- Recog ECU Recognize Img Lane recognition camera sensor assembly image recognition status / Normal or Abnormal Normal: Normal image recognition
Abnormal: Image recognition malfunction- Recog ECU H Temp Hist Lane recognition camera sensor assembly temperature condition history / ON or OFF ON: History of excessive temperature
OFF: No history of excessive temperature- Recognition Camera Voltage Lane recognition camera sensor assembly voltage status / Normal or Low Normal: Normal voltage
Low: Low voltage- Camera Height Memorized camera height / Min.: 0 mm, Max.: 2500 mm Memorized camera height displayed - Camera Horizontal Memorized camera horizontal position / Min.: -32768 mm, Max.: 32767 mm Memorized camera horizontal position displayed - Target Height Memorized target height / Min.: 0 mm, Max.: 2000 mm Memorized target height displayed - Target Distance Memorized target distance / Min.: 0 mm, Max.: 5000 mm Memorized distance from camera to target displayed - Curr Com PCS-WIL-R Front active headrest ECU RH connection status / without or with with: Front active headrest ECU RH connected
without: Front active headrest ECU RH not connected- Curr Com PCS-WIL-L Front active headrest ECU LH connection status / without or with with: Front active headrest ECU LH connected
without: Front active headrest ECU LH not connected- Curr Com Night View ECU Night view ECU connection status / without or with with: Night view ECU connected
without: Night view ECU not connected- Country# (DSS) Driving support ECU country signal / JPN, NA, EURO, AUS, OTHER, TWN, CHINA, THAI, GCC or NOFIX NA - Country# (Obj Recog ECU) Lane recognition camera sensor assembly country signal / JPN, NA, EURO, AUS, OTHER, TWN, CHINA, THAI, GCC or NOFIX NA - The Number of DTCs Number of stored trouble codes / Min.: 0, Max.: 255 Number of stored DTCs displayed -
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus:
Body Electrical / (desired system) / Active Test.
Chassis / ABS/VSC/TRAC / Active Test.
- According to the display on the Techstream, perform the Active Test.PRE-COLLISION
Tester Display Test Part Control Range Diagnostic Note Driver Seat Belt Motor Driver side seat belt motor ON/OFF The seat belt (driver side) is fastened. Passenger Seat Belt Motor Passenger side seat belt motor ON/OFF The seat belt (passenger side) is fastened. Driver and Passenger Seat Belt Motor Driver and passenger side seat belt motor ON/OFF The seat belts (driver and passenger side) are fastened. PRE-COLLISION 2Tester Display Test Part Control Range Diagnostic Note Face Direction Check Driver monitor camera ON/OFF - ABS/VSC/TRACTester Display Test Part Control Range Diagnostic Note Buzzer Skid control buzzer ON/OFF The buzzer can be heard. COMBINATION METERTester Display Test Part Control Range Diagnostic Note Indicat. Precrash PCS indicator light ON/OFF Confirm that the vehicle is stopped with the engine idling.