LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> GS 450h Base >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Pre-Collision System (Diagnostics - Introduction) >> Pre-Collision System >> Data List / Active Test [10/2015 - ] >> Data List / Active Test [10/2015 - ]

Data List / Active Test [10/2015 - ]

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.
    5. Read the Data List according to the display on the Techstream.
      PRE-COLLISION 2

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Turn Light RH Turn signal switch (right) status / ON or OFF ON: Turn signal switch (right) on
      OFF: Turn signal switch (right) off      		 -
      Turn Light LH Turn signal switch (left) status / ON or OFF ON: Turn signal switch (left) on
      OFF: Turn signal switch (left) off      		 -
      PCS OFF Switch Pre-collision system on/off status / ON or OFF ON: Pre-collision system on
      OFF: Pre-collision system off      		 -
      Pre-Collision Safety Warning Buzzer Pre-collision system warning buzzer / Valid or Inval Valid: Pre-collision system warning buzzer operation possible
      Inval: Pre-collision system warning buzzer operation not possible      		 -
      Pre-Collision Brake Pre-collision brake function / Valid or Inval Valid: Pre-collision brake operation possible
      Inval: Pre-collision brake operation not possible      		 -
      PBA Start Pre-collision brake assist activation signal / OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-collision brake assist not operating
      Standby: Brake pedal not depressed during pre-collision brake assist operation
      Assist Lv1: Brake pedal depressed during pre-collision brake assist operation
      Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation      		 Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)
      Warning Brake - - Not applicable to the vehicle
      Brake Assist Standby - - This item is displayed on the Techstream but is not used.
      Pre-Collision Brake Control Pre-collision brake operational status / ON or OFF ON: Pre-collision brake operating
      OFF: Pre-collision brake not operating      		 -
      AVS Start AVS control activation status / ON or OFF ON: AVS control activated
      OFF: AVS control not activated      		 -
      VGRS Start - - Not applicable to the vehicle
      PBA Control Pre-collision brake assist operational status / Valid or Invalid Valid: Pre-collision brake assist control operation possible
      Invalid: Pre-collision brake assist control operation not possible      		 -
      Pre-Collision Safety Brake Ind Pre-collision system alarm warning message status / ON or OFF ON: Displayed
      OFF: Not displayed      		 "BRAKE!" is displayed
      PCS Crash Alarm Buzzer Skid control buzzer status / ON or OFF ON: Skid control buzzer sounding
      OFF: Skid control buzzer not sounding      		 -
      Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history / ON or OFF ON: History of low voltage
      OFF: No history of low voltage      		 -
      Front Radar-Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history / ON or OFF ON: History of vertical misalignment
      OFF: No history of vertical misalignment      		 -
      Front Radar-Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history / ON or OFF ON: History of horizontal misalignment
      OFF: No history of horizontal misalignment      		 -
      Front Recognition Camera-Malfunction History Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.) / ON or OFF ON: History of malfunction
      OFF: No history of malfunction      		 -
      Control Mode ECU control mode status / Normal or Check Normal: Normal operation
      Check: Operating in Control Mode      		 -
      PCS Operation State Retention Setting PCS Operation State Retention Setting customize setting / ON or OFF ON: Customize setting set to ON
      OFF: Customize setting set to OFF      		 -
      PCS Alarm Activation Distance Retention Setting 1 PCS Alarm Activation Distance Retention Setting 1 customize setting / ON or OFF ON: Customize setting set to ON
      OFF: Customize setting set to OFF      		 -
      PCS Alarm Activation Distance Retention Setting 2 PCS Alarm Activation Distance Retention Setting 2 customize setting / ON or OFF ON: Customize setting set to ON
      OFF: Customize setting set to OFF      		 -
      PCS Alarm Activation Distance Retention Setting 3 PCS Alarm Activation Distance Retention Setting 3 customize setting / ON or OFF ON: Customize setting set to ON
      OFF: Customize setting set to OFF      		 -
    6. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
    7. Read the Data List according to the display on the Techstream.
      ABS/VSC/TRAC

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch status / ON or OFF ON: Brake pedal depressed
      OFF: Brake pedal released      		 -
      Stop Light Relay Output STPO terminal output condition / ON or OFF ON: Output
      OFF: Not output      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.
    5. Perform the Active Test according to the display on the Techstream.
      PRE-COLLISION 2

      Tester Display Test Part Control Range Diagnostic Note
      PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with power switch on (IG), vehicle stopped
    6. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
    7. Perform the Active Test according to the display on the Techstream.
      ABS/VSC/TRAC

      Tester Display Test Part Control Range Diagnostic Note
      Stop Light Relay Stop lights ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)
    8. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    9. Perform the Active Test according to the display on the Techstream.
      COMBINATION METER

      Tester Display Test Part Control Range Diagnostic Note
      Indicat. Pre-Collision PCS OFF warning light ON / OFF -
scientia non olet · About LEMON Manuals