| C1591/51 |
Actuator Neutral Position Calibration Undone |
Control is not started |
| C1592/52 |
Actuator Neutral Position Calibration Incomplete |
Control is not started |
| C1593/53 |
Actuator Standard Position |
Control is not started |
| C1595/55 |
Lost Communication with Steering Angle Sensor Module (SIL) |
Returns the front relative angle to the neutral position and stops or stops at the current position |
| C1597/57 |
Lost Communication between VGRS and DRS |
Returns the front relative angle to the neutral position and stops |
| C15A1/61 |
Short in Motor Circuit |
Control is not started or stops |
| C15A2/62 |
Open in Motor Circuit |
Control is not started or stops |
| C15A3/63 |
Motor Rotation Angle Not Detected |
Control is not started |
| C15A4/64 |
Motor Rotation Angle Malfunction |
Control is not stopped |
| C15A5/65 |
Lock Mechanism Circuit |
Control is not started or stops |
| C15A6/62 |
Actuator Motor Power Distribution Malfunction |
Control is not started or stops |
| C15A9/66 |
Lock Holder Deviation Detection |
Control is not started or stops |
| C15AA/66 |
Lock Mechanism Release Incomplete |
Control is not stopped |
| C15AB/66 |
Lock Mechanism Insertion |
Control is not started or stops |
| C15B1/71 |
ECU Malfunction (CPU) |
Control is not started or stops |
| C15B2/72 |
ECU Malfunction (Internal Line) |
Control is not started or stops |
| C15B3/73 |
ECU Malfunction (Substrate Temperature Sensor) |
Control continues |
| C15B4/71 |
ECU Malfunction (Actuator Angle Record) |
Control is not started or stops |
| C15B5/82 |
ECU Malfunction (Flash Memory) |
Control is not started or stops |
| C15B6/83 |
ECU Malfunction (EEPROM) |
Control is not started or stops |
| C15C1/74 |
Steering Angle Sensor |
Control is not started or stops |
| C15C2/74 |
Steering Angle Sensor B+ |
Returns the front relative angle and rear turning angle to the neutral position |
| C15C3/75 |
Brake System Control Module |
Returns the front relative angle and rear turning angle to the neutral position |
| C15C4/68 |
Steering Signal Not Detected |
- |
| C15C5/69 |
Motor Rotation Signal Not Detected |
- |
| C15C6/77 |
IG Power Supply Voltage |
Returns the front relative angle and rear turning angle to the neutral position |
| C15C7/78 |
DC Motor Power Source Voltage |
Control is not started or stops |
| C15C8/79 |
Power Supply Relay Failure |
Control is not started |
| C15C9/76 |
DRS System Malfunction |
Returns the front relative angle and rear turning angle to the neutral position |
| C15CA/79 |
EPS System Malfunction |
Returns the front relative angle and rear turning angle to the neutral position |
| C15CB/84 |
VSC System Malfunction |
Returns the front relative angle and rear turning angle to the neutral position |
| U0100/56 |
Lost Communication with ECM/PCM "A" |
Control is not started |
| U0101/56 |
Lost Communication with TCM |
Returns the front relative angle and rear turning angle to the neutral position |
| U0125/56 |
Lost Communication with Yaw Rate Sensor Module |
Control continues |
| U0126/56 |
Lost Communication with Steering Angle Sensor Module |
Returns the front relative angle and rear turning angle to the neutral position |
| U0129/56 |
Lost Communication with Brake System Control Module |
Returns the front relative angle and rear turning angle to the neutral position |
| U0131/56 |
Lost Communication with Power Steering Control Module |
Returns the front relative angle and rear turning angle to the neutral position |
| U0134/56 |
Lost Communication with DRS Module |
Returns the front relative angle and rear turning angle to the neutral position |