How To Proceed With Troubleshooting [09/2014 - ]: Procedure

Result

Result:  1

NEXT 

See step  2

1. Measure the auxiliary battery voltage.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

   HINT: 

   A simple method to determine whether the auxiliary battery is discharged is to operate the horn.

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  3

HINT: 

If the power switch cannot be turned on (IG), communication with the Techstream can be confirmed by connecting the Techstream to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins.

Result

Result:  1

NEXT 

See step  4

1. Use the Techstream to check if the CAN communication system is functioning normally.

   Refer to DIAGNOSIS SYSTEM [09/2014 - 10/2015] or DIAGNOSIS SYSTEM [10/2015 - ]

   Result

   Result	Proceed to
   CAN DTC is not output	A
   CAN DTC is output	B

Result:  2

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - 10/2015]  or  DIAGNOSTIC TROUBLE CODE CHART [10/2015 - ] 

Result:  1

A 

See step  5

1. Use the Techstream to check if the LIN communication system is functioning normally.

   Refer to DTC CHECK / CLEAR [09/2014 - ]

   Result

   Result	Proceed to
   LIN DTC is not output	A
   LIN DTC is output	B

Result:  2

B 

GO TO LIN COMMUNICATION SYSTEM. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - ] 

Result:  1

A 

See step  6

1. Check for DTCs and make a note of any codes that are output.

   Refer to DTC CHECK / CLEAR [09/2014 - ] 

2. Based on the DTCs output above, proceed to each diagnostic procedure.

   Result

   Result	Proceed to
   DTC is not output	A
   Hybrid control system DTC is output	B
   Steering lock system DTC is output	C
   Engine immobilizer system DTC is output	D

Result:  2

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - 10/2015]  or  DIAGNOSTIC TROUBLE CODE CHART [10/2015 - 09/2016]  or  DIAGNOSTIC TROUBLE CODE CHART [09/2016 - ] 

Result:  3

C 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - ] 

Result:  6

D 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - ]  

Result:  1

A 

See step  7

1. Refer to Problem Symptoms Table.

   PROBLEM SYMPTOMS TABLE [09/2014 - ] 

   Result

   Result	Proceed to
   Fault is not listed in problem symptoms table	A
   Fault is listed in problem symptoms table	B

Result:  2

B 

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE 

Result:  1

A 

See step  8

1. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [09/2014 - ] 

2. Terminals of ECU

   Refer to TERMINALS OF ECU [09/2014 - 10/2015] or TERMINALS OF ECU [10/2015 - ] 

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  9

Result

Result:  1

NEXT 

See step  10

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [09/2014 - ] 

2. Check for DTCs.

   Refer to DTC CHECK / CLEAR [09/2014 - ] 

   HINT: 

   Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [09/2014 - ] 

   Result

   Result	Proceed to
   DTC is not output	A
   Engine immobilizer system DTC is output	B

Result:  1

A 

END 

Result:  2

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - ]