Operation Check [09/2014 - 10/2015]

HINT: 

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).

1. Check that the front passenger side power window and rear power windows cannot be operated when the window lock switch of the multiplex network master switch is pressed.

   OK

   Operation of front passenger side power window and rear power windows is disabled.

2. Check that the front passenger side power window and rear power windows can be operated when the window lock switch is pressed again.

   OK

   Front passenger side power window and rear power windows can be operated.

1. Check that the driver side power window operates as follows:
   OK
   
   

   Condition	Multiplex Network Master Switch	Switch Operation	Power Window Operation
   Engine switch on (IG)	Driver side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)

2. Check that the front passenger side window and rear power windows operate as follows:
   OK
   
   

   Condition	Power Window Regulator Switch	Switch Operation	Power Window Operation
   Engine switch on (IG) Window lock switch off	Front passenger side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)
   	Rear LH side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)
   	Rear RH side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)

1. Check that the driver side power window operates as follows:
   OK
   
   

   Condition	Multiplex Network Master Switch	Switch Operation	Power Window Operation
   Engine switch on (IG)	Driver side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)

2. Check that the front passenger side window and rear power windows operate as follows:
   OK
   
   

   Condition	Power Window Regulator Switch	Switch Operation	Power Window Operation
   Engine switch on (IG) Window lock switch off	Front passenger side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)
   	Rear LH side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)
   	Rear RH side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)

1. Check that the front passenger side window and rear power windows operate as follows:
   OK
   
   

   Condition	Multiplex Network Master Switch	Switch Operation	Power Window Operation
   Engine switch on (IG) Window lock switch off	Front passenger side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)
   	Rear LH side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)
   	Rear RH side	Pulled halfway up	Up (Closes)
   		Pushed halfway down	Down (Opens)

1. Check that the front passenger side window and rear power windows operate as follows:
   OK
   
   

   Condition	Multiplex Network Master Switch	Switch Operation	Power Window Operation
   Engine switch on (IG) Window lock switch off	Front passenger side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)
   	Rear LH side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)
   	Rear RH side	Pulled up (One touch operation)	Auto up (Closes)
   		Pushed down (One touch operation)	Auto down (Opens)

1. Check the basic function.
   WARNING:

   • The jam protection function is operative during both the auto up and manual up operation.
   • Do not put your fingers between the door frame and door glass to check functions. Also, prevent any part of your body from being caught during inspection.

   HINT: 

   The jam protection function is operative during both the auto up and manual up operation while the engine is running or the engine switch is turned to on (IG), and also for 43 seconds after the engine switch is turned off.

   1. Fully open the window.
   2. Set a check jig wrapped with a piece of cloth near the window fully closed position.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      TEXT IN ILLUSTRATION
      
      

      *1	Check Jig
      *2	Cloth

   3. Operate the auto up or manual up function to check that the power window stops and goes down after the check jig is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.) or until approximately 5 seconds elapse.

      HINT: 

      If the check jig is caught when the opening is approximately 75 mm (2.95 in.) or more, the power window goes down for approximately 125 mm (4.93 in.) or until approximately 2.5 seconds elapse.

   4. While the power window is moving down, check that the door glass cannot be moved up even when the power window regulator switch is used.

1. Check that all the power windows can be operated with the multiplex network master switch after the engine switch is turned off.
2. Check that the key-off operation function does not operate after a front door is opened.
3. Check that none of the power windows can be operated after more than approximately 43 seconds have elapsed since the engine switch was turned off.

HINT: 

This inspection is possible only when the key-linked open and close function is set to ON through the customize function using the Techstream (the default setting is OFF).

1. Check that all power windows operate as follows:
   OK
   
   

   Condition	Door Key Cylinder Operation	Power Window
   No key is inside vehicle and all doors are closed	Held in lock position for more than 2.3 seconds	Up (Closes)
   	Returned to neutral position	Stops
   	Held in unlock position for more than 2.3 seconds	Down (Opens)
   	Returned to neutral position	Stop

HINT: 

This inspection is possible only when the wireless transmitter-linked open and close function is set to ON through the customize function using the Techstream (the default setting is OFF).

1. Check that all power windows operate as follows when operating the transmitter:
   OK
   
   

   Condition	Transmitter Operation	Power Window
   No key is inside vehicle, and all doors are closed and locked	UNLOCK switch pressed for more than 3.0 seconds	Down (Opens)
   	UNLOCK switch released	Stops

1. Check the LED illumination (multiplex network master switch assembly).
   1. Check that the LEDs located on the multiplex network master switch assembly illuminate when the engine switch is turned on (IG).
2. Check the LED illumination (front power window regulator switch assembly RH).
   1. Check that the LED located on the power window regulator switch assembly (for front passenger side) illuminates when the engine switch is turned on (IG).

      HINT: 

      If the window lock switch is on, the LED located on the power window regulator switch assembly (for front passenger side) does not illuminate. Therefore, turn the window lock switch off before checking the LED illumination.

3. Check the LED illumination (rear power window regulator switch assembly LH and rear power window regulator motor switch assembly RH).
   1. Check that the LED located on rear power window regulator switch assembly LH and rear power window regulator motor switch assembly RH illuminates when the engine switch is turned on (IG).

      HINT: 

      If the window lock switch is on, the LEDs located on the power window regulator switch assemblies (rear power window regulator switch assembly LH and rear power window regulator motor switch assembly RH) do not illuminate. Therefore, turn the window lock switch off before checking the LED illumination.