| Engine does not crank (Does not start) |
Battery |
Refer to PROCEDURE - Step 1 |
| ST relay |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Starter assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| VC output circuit (ECM 5 V output) |
Refer to VC Output Circuit [04/2013 - 08/2015] |
| Starter signal circuit |
Refer to Starter Signal Circuit [04/2013 - 08/2015] |
| Smart access system with push-button start (for start function) |
Refer to PROBLEM SYMPTOMS TABLE [04/2013 - 06/2014]
, or refer to PROBLEM SYMPTOMS TABLE [06/2014 - ] |
| Park/neutral position switch assembly (for 2WD models) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Park/neutral position switch assembly (for AWD models) |
Refer to INSPECTION [04/2013 - ] |
| No initial combustion (Does not start) |
Engine immobiliser system |
Refer to PROBLEM SYMPTOMS TABLE [04/2013 - 06/2014] Refer to PROBLEM SYMPTOMS TABLE [06/2014 - 09/2022] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| VC output circuit (ECM 5 V output) |
Refer to VC Output Circuit [04/2013 - 08/2015] |
| Crankshaft position sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| VVT sensor (for intake camshaft) |
Refer to DTC P0340: Camshaft Position Sensor Circuit Malfunction; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor); DTC P0345: Camshaft Position Sensor "A" Circuit (Bank 2); DTC P0347: Camshaft Position Sensor "A" Circuit Low Input (Bank 2); DTC P0348: Camshaft Position Sensor "A" Circuit High Input (Bank 2) [04/2013 - 06/2014]
, or refer to DTC P0340: Camshaft Position Sensor Circuit; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor); DTC P0345: Camshaft Position Sensor "A" Circuit (Bank 2); DTC P0347: Camshaft Position Sensor "A" Circuit Low Input (Bank 2); DTC P0348: Camshaft Position Sensor "A" Circuit High Input (Bank 2) [06/2014 - 08/2015] |
| VVT sensor (for exhaust camshaft) |
Refer to DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1); DTC P0390: Camshaft Position Sensor "B" Circuit (Bank 2); DTC P0392: Camshaft Position Sensor "B" Circuit Low Input (Bank 2); DTC P0393: Camshaft Position Sensor "B" Circuit High Input (Bank 2) [04/2013 - 08/2015] |
| Fuel pump control circuit |
Refer to Fuel Pump Control Circuit [04/2013 - 08/2015] |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Valve timing |
Refer to PROCEDURE - Step 4 |
| Starter signal circuit |
Refer to Starter Signal Circuit [04/2013 - 08/2015] |
| ECM |
Refer to REMOVAL [04/2013 - 08/2015] |
| Engine cranks normally but difficult to start |
Fuel pump control circuit |
Refer to Fuel Pump Control Circuit [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Engine coolant temperature sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Fuel injector assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Compression |
Refer to PROCEDURE - Step 10 |
| Intake system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Throttle body with motor assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| PCV hose |
Refer to COMPONENTS [04/2013 - 08/2015] |
| Starter signal circuit |
Refer to Starter Signal Circuit [04/2013 - 08/2015] |
| Cold start injector circuit |
Refer to Cold Start Injector Circuit [04/2013 - 08/2015] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| Incomplete intermittent combustion occurs (Does not start) |
Fuel pump control circuit |
Refer to Fuel Pump Control Circuit [04/2013 - 08/2015] |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Fuel line |
- |
| Fuel pump (for low pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel injector assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Crankshaft position sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| VVT sensor (for intake camshaft) |
Refer to DTC P0340: Camshaft Position Sensor Circuit Malfunction; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor); DTC P0345: Camshaft Position Sensor "A" Circuit (Bank 2); DTC P0347: Camshaft Position Sensor "A" Circuit Low Input (Bank 2); DTC P0348: Camshaft Position Sensor "A" Circuit High Input (Bank 2) [04/2013 - 06/2014]
, or refer to DTC P0340: Camshaft Position Sensor Circuit; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor); DTC P0345: Camshaft Position Sensor "A" Circuit (Bank 2); DTC P0347: Camshaft Position Sensor "A" Circuit Low Input (Bank 2); DTC P0348: Camshaft Position Sensor "A" Circuit High Input (Bank 2) [06/2014 - 08/2015] |
| VVT sensor (for exhaust camshaft) |
Refer to DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1); DTC P0390: Camshaft Position Sensor "B" Circuit (Bank 2); DTC P0392: Camshaft Position Sensor "B" Circuit Low Input (Bank 2); DTC P0393: Camshaft Position Sensor "B" Circuit High Input (Bank 2) [04/2013 - 08/2015] |
| Valve timing |
Refer to PROCEDURE - Step 4 |
| Starter signal circuit |
Refer to Starter Signal Circuit [04/2013 - 08/2015] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| High engine speed |
Air conditioning signal circuit |
Refer to PROBLEM SYMPTOMS TABLE [04/2013 - 08/2015] |
| Throttle body with motor assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Intake system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Engine coolant temperature sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| PCV hose |
Refer to COMPONENTS [04/2013 - 08/2015] |
| PCV system |
- |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| ACIS control circuit |
Refer to ACIS Control Circuit [04/2013 - 08/2015] |
| Low engine speed (Poor idle) |
Fuel pump control circuit |
Refer to Fuel Pump Control Circuit [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Throttle body with motor assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Intake system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| ACIS control circuit |
Refer to ACIS Control Circuit [04/2013 - 08/2015] |
| PCV hose |
Refer to COMPONENTS [04/2013 - 08/2015] |
| Rough idle |
Compression (engine mechanical) |
Refer to PROCEDURE - Step 10 |
| Air fuel ratio sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| Heated oxygen sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| Mass air flow meter sub-assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Air conditioning signal circuit |
Refer to PROBLEM SYMPTOMS TABLE [04/2013 - 08/2015] |
| Fuel injector assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel line |
- |
| Fuel pump (for low pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Intake system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| ACIS control circuit |
Refer to ACIS Control Circuit [04/2013 - 08/2015] |
| Electronic throttle control system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| PCV hose |
Refer to COMPONENTS [04/2013 - 08/2015] |
| Hunting (Poor idle) |
Electronic throttle control system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Intake system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| PCV hose |
Refer to COMPONENTS [04/2013 - 08/2015] |
| Mass air flow meter sub-assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Air fuel ratio sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| ACIS control circuit |
Refer to ACIS Control Circuit [04/2013 - 08/2015] |
| Hesitation/Poor acceleration (Poor driveability) |
Fuel line |
- |
| Fuel pump (for low pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Spark plug |
Refer to PROCEDURE - Step 3 |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Fuel injector assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| Mass air flow meter sub-assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Throttle body with motor assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Knock control sensor |
Refer to INSPECTION [04/2013 - 08/2015] |
| Compression (engine mechanical) |
Refer to PROCEDURE - Step 10 |
| Brake override system |
Refer to Brake Override System [04/2013 - 08/2015] |
| Surging (Poor driveability) |
Spark plug |
Refer to PROCEDURE - Step 3 |
| Fuel line |
- |
| Fuel pump control circuit |
Refer to Fuel Pump Control Circuit [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Fuel injector assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| Mass air flow meter sub-assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Variable Valve Timing (VVT) system |
Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0018: Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) [04/2013 - 08/2015] |
| Compression (engine mechanical) |
Refer to PROCEDURE - Step 10 |
| Engine stalls soon after starting |
Fuel pump control circuit |
Refer to Fuel Pump Control Circuit [04/2013 - 08/2015] |
| Fuel pump (for low pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel pump (for high pressure side) |
Refer to INSPECTION [04/2013 - 08/2015] |
| Fuel line |
- |
| Spark plug |
Refer to PROCEDURE - Step 3 |
| Ignition system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| Fuel injector assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| ECM power source circuit |
Refer to ECM Power Source Circuit [04/2013 - 08/2015] |
| Mass air flow meter sub-assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Throttle body with motor assembly |
Refer to INSPECTION [04/2013 - 08/2015] |
| Intake system |
Refer to ON-VEHICLE INSPECTION [04/2013 - 08/2015] |
| PCV valve and hose |
Refer to COMPONENTS [04/2013 - 08/2015] |
| Compression (engine mechanical) |
Refer to PROCEDURE - Step 10 |
| Cold start injector circuit |
Refer to Cold Start Injector Circuit [04/2013 - 08/2015] |
| Engine stalls only during A/C operation |
Air conditioning signal circuit |
Refer to PROBLEM SYMPTOMS TABLE [04/2013 - 08/2015] |
| ECM |
Refer to REMOVAL [04/2013 - 08/2015] |
| Cold start injector circuit |
Refer to Cold Start Injector Circuit [04/2013 - 08/2015] |
| Unable/difficult to refuel |
Fuel system (canister, refueling valve, roll over valve, fuel tank, etc.) |
- |
| Drive mode does not change |
Drive mode select switch circuit |
Refer to Drive Mode Select Switch Circuit [04/2013 - 08/2015] |
| SNOW mode does not change |
Pattern select switch snow mode circuit |
Refer to Pattern Select Switch Snow Mode Circuit [04/2013 - 08/2015] |