LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2013 >> LS 460 Base, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> Can Communication System (Diagnostic Codes (U0100 - U1002)) >> Can Communication System >> DTC U1002: Lost Communication with Gateway Module >> Procedure

DTC U1002: Lost Communication with Gateway Module: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Refer to PRECAUTION [09/2012 - ] .

    NEXT: Go to next step 

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      NOTE:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Refer to INITIALIZATION [09/2012 - ] .

    NEXT: Go to next step 

  3. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY418658Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition Resistance: Malfunction
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
      A50-3 (CANP) - A50-1 (FMB3) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
      A50-4 (CANN) - A50-1 (FMB3) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
      A50-3 (CANP) - A50-2 (E) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
      A50-4 (CANN) - A50-2 (E) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Front Multiplex Network Light ECU [Front Controller])
      RESULT

      Result Proceed to
      NG
      • Open in CAN main wire
      		 A
      NG
      • Short in line
      • +B short
      • Ground short
      		 B
      OK C

    B → See step   22 

    C → See step   92 

    A: Go to next step 

  4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - FRONT CONTROLLER) 
    1. Disconnect the No. 10 junction connector.
      GTY410475Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-11 (CANH) - L95-22 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)

    NG → See step   6 

    OK: Go to next step 

  5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - REAR JUNCTION BLOCK ECU) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY419123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-4 (CANH) - L95-15 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)

    NG → See step   14 

    OK → REPLACE NO. 10 JUNCTION CONNECTOR 

  6. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - FRONT CONTROLLER) 
    1. Disconnect the No. 9 junction connector.
      GTY410477Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R48-3 (CANH) - R48-14 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 9 Junction Connector)

    NG → See step   9 

    OK: Go to next step 

  8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY410478Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R48-4 (CANH) - R48-15 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 9 Junction Connector)

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) 

    OK → REPLACE NO. 9 JUNCTION CONNECTOR 

  9. CONNECT CONNECTOR 
    1. Reconnect the R48 No. 9 junction connector.

    NEXT: Go to next step 

  10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - FRONT CONTROLLER) 
    1. Disconnect the No. 8 junction connector.
      GTY411607Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R57-1 (CANH) - R57-3 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to No. 8 Junction Connector)

    NG → See step   12 

    OK: Go to next step 

  11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY411608Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R57-5 (CANH) - R57-7 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to No. 8 Junction Connector)

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR) 

    OK → REPLACE NO. 8 JUNCTION CONNECTOR 

  12. CONNECT CONNECTOR 
    1. Reconnect the R57 No. 8 junction connector.

    NEXT: Go to next step 

  13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (FRONT CONTROLLER - NO. 8 JUNCTION CONNECTOR) 
    1. Disconnect the front multiplex network light ECU (front controller) connector.
      GTY396709Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Front Multiplex Network Light ECU [Front Controller])

    NG → REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO FRONT CONTROLLER (FRONT CONTROLLER - NO. 8 JUNCTION CONNECTOR) 

    OK → REPLACE FRONT MULTIPLEX NETWORK LIGHT ECU (FRONT CONTROLLER) 

  14. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 11 JUNCTION CONNECTOR - REAR JUNCTION BLOCK ECU) 
    1. Disconnect the No. 11 junction connector.
      GTY410472Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-2 (CANH) - S60-13 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)

    NG → See step   17 

    OK: Go to next step 

  16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 11 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY419124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-5 (CANH) - S60-16 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 11 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) 

    OK → REPLACE NO. 11 JUNCTION CONNECTOR 

  17. CONNECT CONNECTOR 
    1. Reconnect the S60 No. 11 junction connector.

    NEXT: Go to next step 

  18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 12 JUNCTION CONNECTOR - REAR JUNCTION BLOCK ECU) 
    1. Disconnect the No. 12 junction connector.
      GTY410482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S59-3 (CANH) - S59-14 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 12 Junction Connector)

    NG → See step   20 

    OK: Go to next step 

  19. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 12 JUNCTION CONNECTOR - NO. 11 JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY410484Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S59-4 (CANH) - S59-15 (CANL) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 12 Junction Connector)

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 12 JUNCTION CONNECTOR - NO. 11 JUNCTION CONNECTOR) 

    OK → REPLACE NO. 12 JUNCTION CONNECTOR 

  20. CONNECT CONNECTOR 
    1. Reconnect the S59 No. 12 junction connector.

    NEXT: Go to next step 

  21. CHECK FOR OPEN IN CAN BUS MAIN WIRE (REAR JUNCTION BLOCK ECU - NO. 12 JUNCTION CONNECTOR) 
    1. Disconnect the luggage room junction block assembly (rear junction block ECU) connector.
      GTY402000Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S62-20 (CANP) - S62-28 (CANN) Engine switch off 108 to 132 Ω
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Luggage Room Junction Block Assembly [Rear Junction Block ECU])

    NG → REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO REAR JUNCTION BLOCK ECU (REAR JUNCTION BLOCK ECU - NO. 12 JUNCTION CONNECTOR) 

    OK → REPLACE LUGGAGE ROOM JUNCTION BLOCK ASSEMBLY 

  22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 12 JUNCTION CONNECTOR SIDE) 
    1. Disconnect the S59 No. 12 junction connector.
      GTY418658Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 108 to 132 Ω
      A50-3 (CANP) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-4 (CANN) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-3 (CANP) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      A50-4 (CANN) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Front Multiplex Network Light ECU [Front Controller])

    NG → See step   32 

    OK: Go to next step 

  23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 12 JUNCTION CONNECTOR - REAR POWER SEAT SWITCH) 
    NOTE:

    For vehicles without a rear power seat control system or seat heater system, go to "Check for Short in CAN Bus Wires (No. 12 Junction Connector - Power Trunk Lid Control ECU)".

    1. Measure the resistance according to the value(s) in the table below.
      GTY413833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S59-1 (CANH) - S59-12 (CANL) Engine switch off 200 Ω or higher
      S59-1 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S59-12 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S59-1 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S59-12 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 12 Junction Connector)
      *b Front view of DLC3

    NG → See step   26 

    OK: Go to next step 

  24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 12 JUNCTION CONNECTOR - POWER TRUNK LID CONTROL ECU) 
    NOTE:

    For vehicles without a power trunk lid system, go to "Check for Short in CAN Bus Wires (No. 12 Junction Connector - Rear Junction Block ECU)".

    1. Measure the resistance according to the value(s) in the table below.
      GTY413831Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S59-2 (CANH) - S59-13 (CANL) Engine switch off 200 Ω or higher
      S59-2 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S59-13 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S59-2 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S59-13 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 12 Junction Connector)
      *b Front view of DLC3

    NG → See step   28 

    OK: Go to next step 

  25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 12 JUNCTION CONNECTOR - REAR JUNCTION BLOCK ECU) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413830Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S59-3 (CANH) - S59-14 (CANL) Engine switch off 108 to 132 Ω
      S59-3 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S59-14 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S59-3 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S59-14 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 12 Junction Connector)
      *b Front view of DLC3

    NG → See step   30 

    OK → REPLACE NO. 12 JUNCTION CONNECTOR 

  26. CONNECT CONNECTOR 
    1. Reconnect the S59 No. 12 junction connector.

    NEXT: Go to next step 

  27. CHECK FOR SHORT IN CAN BUS WIRES (REAR POWER SEAT SWITCH) 
    1. Disconnect the rear power seat switch connector.
      GTY407838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *A for 4-Passenger with Ottoman *B except 4-Passenger with Ottoman
      *a Front view of wire harness connector
      (to Rear Power Seat Switch)      		 *b Front view of DLC3
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      FOR 4-PASSENGER WITH OTTOMAN

      Tester Connection Switch Condition Specified Condition
      S15-13 (CANH) - S15-14 (CANL) Engine switch off 54 to 69 Ω
      S15-13 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S15-14 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S15-13 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S15-14 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      EXCEPT 4-PASSENGER WITH OTTOMAN

      Tester Connection Switch Condition Specified Condition
      r2-5 (CANH) - r2-4 (CANL) Engine switch off 54 to 69 Ω
      r2-5 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      r2-4 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      r2-5 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      r2-4 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      RESULT

      Result Proceed to
      OK (for 4-Passenger with Ottoman) A
      OK (for 5-Passenger with Ottoman) B
      OK (for Power Seat) C
      OK (for Fixed Seat Type) D
      NG E

    B → See step   93 

    C → See step   111 

    D → See step   112 

    E → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO REAR POWER SEAT SWITCH (CANH, CANL) 

    A → See step   94 

  28. CONNECT CONNECTOR 
    1. Reconnect the S59 No. 12 junction connector.

    NEXT: Go to next step 

  29. CHECK FOR SHORT IN CAN BUS WIRES (POWER TRUNK LID CONTROL ECU) 
    1. Disconnect the power trunk lid control ECU (luggage closer motor assembly) connector.
      GTY414961Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S43-6 (CANP) - S43-5 (CANN) Engine switch off 54 to 69 Ω
      S43-6 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      S43-5 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      S43-6 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S43-5 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Power Trunk Lid Control ECU [Luggage Closer Motor Assembly])
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER TRUNK LID CONTROL ECU (CANP, CANN) 

    OK → See step   95 

  30. CONNECT CONNECTOR 
    1. Reconnect the S59 No. 12 junction connector.

    NEXT: Go to next step 

  31. CHECK FOR SHORT IN CAN BUS WIRES (REAR JUNCTION BLOCK ECU) 
    1. Disconnect the luggage room junction block assembly (rear junction block ECU) connector.
      GTY405355Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S62-20 (CANP) - S62-28 (CANN) Engine switch off 108 to 132 Ω
      S62-20 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      S62-28 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      S62-20 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S62-28 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Luggage Room Junction Block Assembly [Rear Junction Block ECU])
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO REAR JUNCTION BLOCK ECU (CANP, CANN) 

    OK → REPLACE LUGGAGE ROOM JUNCTION BLOCK ASSEMBLY 

  32. CONNECT CONNECTOR 
    1. Reconnect the S59 No. 12 junction connector.

    NEXT: Go to next step 

  33. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 11 JUNCTION CONNECTOR - NO. 12 JUNCTION CONNECTOR) 
    1. Disconnect the No. 11 junction connector.
      GTY419824Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-2 (CANH) - S60-13 (CANL) Engine switch off 108 to 132 Ω
      S60-2 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-13 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-2 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S60-13 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 11 JUNCTION CONNECTOR - NO. 12 JUNCTION CONNECTOR) 

    OK: Go to next step 

  34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 JUNCTION CONNECTOR SIDE) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY418658Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 108 to 132 Ω
      A50-3 (CANP) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-4 (CANN) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-3 (CANP) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      A50-4 (CANN) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Front Multiplex Network Light ECU [Front Controller])

    NG → See step   47 

    OK: Go to next step 

  35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY) 
    NOTE:

    For vehicles without a pre-collision system, go to "Check for Short in CAN Bus Wires (No. 11 Junction Connector - Rear Multiplex Network Door ECU LH)".

    1. Measure the resistance according to the value(s) in the table below.
      GTY413829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-6 (CANH) - S60-17 (CANL) Engine switch off 200 Ω or higher
      S60-6 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-17 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-6 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S60-17 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)
      *b Front view of DLC3

    NG → See step   39 

    OK: Go to next step 

  36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 JUNCTION CONNECTOR - REAR MULTIPLEX NETWORK DOOR ECU LH) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413836Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-3 (CANH) - S60-14 (CANL) Engine switch off 200 Ω or higher
      S60-3 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-14 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-3 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S60-14 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)
      *b Front view of DLC3

    NG → See step   41 

    OK: Go to next step 

  37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 JUNCTION CONNECTOR - FRONT MULTIPLEX NETWORK DOOR ECU LH) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413835Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-4 (CANH) - S60-15 (CANL) Engine switch off 200 Ω or higher
      S60-4 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-15 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-4 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S60-15 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)
      *b Front view of DLC3

    NG → See step   43 

    OK: Go to next step 

  38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413827Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      S60-1 (CANH) - S60-12 (CANL) Engine switch off 200 Ω or higher
      S60-1 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-12 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      S60-1 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      S60-12 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 11 Junction Connector)
      *b Front view of DLC3

    NG → See step   45 

    OK → REPLACE NO. 11 JUNCTION CONNECTOR 

  39. CONNECT CONNECTOR 
    1. Reconnect the S60 No. 11 junction connector.

    NEXT: Go to next step 

  40. CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY) 
    1. Disconnect the driving support ECU assembly connector.
      GTY414834Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A33-19 (CANP) - A33-18 (CANN) Engine switch off 54 to 69 Ω
      A33-19 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      A33-18 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      A33-19 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      A33-18 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Driving Support ECU Assembly)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT ECU ASSEMBLY (CANP, CANN) 

    OK → See step   99 

  41. CONNECT CONNECTOR 
    1. Reconnect the S60 No. 11 junction connector.

    NEXT: Go to next step 

  42. CHECK FOR SHORT IN CAN BUS WIRES (REAR MULTIPLEX NETWORK DOOR ECU LH) 
    1. Disconnect the rear multiplex network door ECU LH connector.
      GTY401536Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      O14-9 (CANP) - O14-10 (CANN) Engine switch off 54 to 69 Ω
      O14-9 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      O14-10 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      O14-9 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      O14-10 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Rear Multiplex Network Door ECU LH)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO REAR MULTIPLEX NETWORK DOOR ECU LH (CANP, CANN) 

    OK → See step   97 

  43. CONNECT CONNECTOR 
    1. Reconnect the S60 No. 11 junction connector.

    NEXT: Go to next step 

  44. CHECK FOR SHORT IN CAN BUS WIRES (FRONT MULTIPLEX NETWORK DOOR ECU LH) 
    1. Disconnect the front multiplex network door ECU LH connector.
      GTY401537Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      N10-9 (CANP) - N10-10 (CANN) Engine switch off 54 to 69 Ω
      N10-9 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      N10-10 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      N10-9 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      N10-10 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Front Multiplex Network Door ECU LH)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT MULTIPLEX NETWORK DOOR ECU LH (CANP, CANN) 

    OK → See step   98 

  45. CONNECT CONNECTOR 
    1. Reconnect the S60 No. 11 junction connector.

    NEXT: Go to next step 

  46. CHECK FOR OPEN IN CAN BUS MAIN WIRE (FRONT POWER SEAT SWITCH LH) 
    1. Disconnect the front power seat switch LH connector.
      GTY414952Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      e46-25 (CANP) - e46-24 (CANN) Engine switch off 54 to 69 Ω
      e46-25 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      e46-24 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      e46-25 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      e46-24 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Front Power Seat Switch LH)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT POWER SEAT SWITCH LH (CANP, CANN) 

    OK → See step   96 

  47. CONNECT CONNECTOR 
    1. Reconnect the S60 No. 11 junction connector.

    NEXT: Go to next step 

  48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - NO. 11 JUNCTION CONNECTOR) 
    1. Disconnect the No. 10 junction connector.
      GTY419825Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-4 (CANH) - L95-15 (CANL) Engine switch off 108 to 132 Ω
      L95-4 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-15 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-4 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-15 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 JUNCTION CONNECTOR - NO. 11 JUNCTION CONNECTOR) 

    OK: Go to next step 

  49. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY418658Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 108 to 132 Ω
      A50-3 (CANP) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-4 (CANN) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-3 (CANP) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      A50-4 (CANN) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Front Multiplex Network Light ECU [Front Controller])

    NG → See step   75 

    OK: Go to next step 

  50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - TIRE PRESSURE WARNING RECEIVER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413740Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-2 (CANH) - L95-13 (CANL) Engine switch off 200 Ω or higher
      L95-2 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-13 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-2 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-13 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   58 

    OK: Go to next step 

  51. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - MAIN BODY ECU) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-3 (CANH) - L95-14 (CANL) Engine switch off 200 Ω or higher
      L95-3 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-14 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-3 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-14 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   60 

    OK: Go to next step 

  52. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - CERTIFICATION ECU) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY419806Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-5 (CANH) - L95-16 (CANL) Engine switch off 200 Ω or higher
      L95-5 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-16 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-5 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-16 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   62 

    OK: Go to next step 

  53. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413742Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-6 (CANH) - L95-17 (CANL) Engine switch off 200 Ω or higher
      L95-6 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-17 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-6 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-17 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   64 

    OK: Go to next step 

  54. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - NO. 1 METER ECU SUB-ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-7 (CANH) - L95-18 (CANL) Engine switch off 200 Ω or higher
      L95-7 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-18 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-7 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-18 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   66 

    OK: Go to next step 

  55. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - WINDSHIELD WIPER SWITCH ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-8 (CANH) - L95-19 (CANL) Engine switch off 200 Ω or higher
      L95-8 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-19 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-8 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-19 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   68 

    OK: Go to next step 

  56. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - STEERING PAD ECU) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413747Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-9 (CANH) - L95-20 (CANL) Engine switch off 200 Ω or higher
      L95-9 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-20 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-9 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-20 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   70 

    OK: Go to next step 

  57. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - OUTER MIRROR SWITCH ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413746Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L95-10 (CANH) - L95-21 (CANL) Engine switch off 200 Ω or higher
      L95-10 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-21 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L95-10 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L95-21 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 10 Junction Connector)
      *b Front view of DLC3

    NG → See step   73 

    OK → REPLACE NO. 10 JUNCTION CONNECTOR 

  58. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  59. CHECK FOR SHORT IN CAN BUS WIRES (TIRE PRESSURE WARNING RECEIVER ASSEMBLY) 
    1. Disconnect the tire pressure warning receiver assembly connector.
      GTY411894Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L163-3 (CANP) - L163-6 (CANN) Engine switch off 54 to 69 Ω
      L163-3 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L163-6 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L163-3 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L163-6 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Tire Pressure Warning Receiver Assembly)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO TIRE PRESSURE WARNING RECEIVER ASSEMBLY (CANP, CANN) 

    OK → See step   100 

  60. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  61. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) 
    1. Disconnect the main body ECU (driver side junction block) connector.
      GTY408440Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L11-16 (CANP) - L11-15 (CANN) Engine switch off 54 to 69 Ω
      L11-16 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L11-15 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L11-16 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L11-15 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Main Body ECU [Driver Side Junction Block])
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN) 

    OK → REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK) 

  62. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  63. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU) 
    1. Disconnect the certification ECU (smart key ECU assembly) connector.
      GTY414829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L15-27 (CANH) - L15-28 (CANL) Engine switch off 54 to 69 Ω
      L15-27 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      L15-28 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      L15-27 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L15-28 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Certification ECU [Smart Key ECU Assembly])
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL) 

    OK → See step   101 

  64. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  65. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU) 
    1. Disconnect the multiplex tilt and telescopic ECU connector.
      GTY401642Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L34-5 (CANP) - L34-14 (CANN) Engine switch off 54 to 69 Ω
      L34-5 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L34-14 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L34-5 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L34-14 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Multiplex Tilt and Telescopic ECU)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN) 

    OK → See step   102 

  66. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  67. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 METER ECU SUB-ASSEMBLY) 
    1. Disconnect the No. 1 meter ECU sub-assembly connector.
      GTY409111Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L10-22 (CANP) - L10-23 (CANN) Engine switch off 54 to 69 Ω
      L10-22 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L10-23 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L10-22 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L10-23 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to No. 1 Meter ECU Sub-assembly)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NO. 1 METER ECU SUB-ASSEMBLY (CANP, CANN) 

    OK → See step   103 

  68. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  69. CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER SWITCH ASSEMBLY) 
    1. Disconnect the windshield wiper switch assembly connector.
      GTY397630Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L25-5 (CANP) - L25-6 (CANN) Engine switch off 54 to 69 Ω
      L25-5 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L25-6 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L25-5 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L25-6 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Windshield Wiper Switch Assembly)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO WINDSHIELD WIPER SWITCH ASSEMBLY (CANP, CANN) 

    OK → See step   104 

  70. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  71. CHECK FOR SHORT IN CAN BUS WIRES (STEERING PAD ECU) 
    1. Disconnect the spiral cable sub-assembly connector.
      GTY402222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L134-10 (CANP) - L134-9 (CANN) Engine switch off 54 to 69 Ω
      L134-10 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L134-9 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L134-10 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L134-9 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Spiral Cable Sub-assembly)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING PAD ECU (CANP, CANN) 

    OK: Go to next step 

  72. INSPECT SPIRAL CABLE SUB-ASSEMBLY 
    1. Remove the spiral cable sub-assembly. Refer to REMOVAL [09/2012 - ] .
      GTY408539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Set the spiral cable sub-assembly to the center position. Refer to INSTALLATION [09/2012 - ] .
    3. Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.
    4. After steering the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A-10 (CANP) - B-2 (CANP) Always Below 3 Ω
      A-9 (CANN) - B-1 (CANN) Always Below 3 Ω
    5. After steering the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A-10 (CANP) - B-2 (CANP) Always Below 3 Ω
      A-9 (CANN) - B-1 (CANN) Always Below 3 Ω

    NG → See step   106 

    OK → See step   105 

  73. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  74. CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR SWITCH ASSEMBLY) 
    1. Disconnect the outer mirror switch assembly connector.
      GTY397277Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      L6-2 (CANP) - L6-3 (CANN) Engine switch off 54 to 69 Ω
      L6-2 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      L6-3 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      L6-2 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      L6-3 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Outer Mirror Switch Assembly)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR SWITCH ASSEMBLY (CANP, CANN) 

    OK → See step   107 

  75. CONNECT CONNECTOR 
    1. Reconnect the L95 No. 10 junction connector.

    NEXT: Go to next step 

  76. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) 
    1. Disconnect the No. 9 junction connector.
      GTY413748Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R48-4 (CANH) - R48-15 (CANL) Engine switch off 108 to 132 Ω
      R48-4 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      R48-15 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      R48-4 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      R48-15 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 9 Junction Connector)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) 

    OK: Go to next step 

  77. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY418658Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 108 to 132 Ω
      A50-3 (CANP) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-4 (CANN) - A50-2 (E) Engine switch off 200 Ω or higher
      A50-3 (CANP) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      A50-4 (CANN) - A50-1 (FMB3) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Front Multiplex Network Light ECU [Front Controller])

    NG → See step   84 

    OK: Go to next step 

  78. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - FRONT MULTIPLEX NETWORK DOOR ECU RH) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY419807Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R48-1 (CANH) - R48-12 (CANL) Engine switch off 200 Ω or higher
      R48-1 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      R48-12 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      R48-1 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      R48-12 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 9 Junction Connector)
      *b Front view of DLC3

    NG → See step   80 

    OK: Go to next step 

  79. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - REAR MULTIPLEX NETWORK DOOR ECU RH) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY413750Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R48-2 (CANH) - R48-13 (CANL) Engine switch off 200 Ω or higher
      R48-2 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      R48-13 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      R48-2 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      R48-13 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 9 Junction Connector)
      *b Front view of DLC3

    NG → See step   82 

    OK → REPLACE NO. 9 JUNCTION CONNECTOR 

  80. CONNECT CONNECTOR 
    1. Reconnect the R48 No. 9 junction connector.

    NEXT: Go to next step 

  81. CHECK FOR SHORT IN CAN BUS WIRES (FRONT MULTIPLEX NETWORK DOOR ECU RH) 
    1. Disconnect the front multiplex network door ECU RH connector.
      GTY401538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      N1-9 (CANP) - N1-10 (CANN) Engine switch off 54 to 69 Ω
      N1-9 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      N1-10 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      N1-9 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      N1-10 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Front Multiplex Network Door ECU RH)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT MULTIPLEX NETWORK DOOR ECU RH (CANP, CANN) 

    OK → See step   108 

  82. CONNECT CONNECTOR 
    1. Reconnect the R48 No. 9 junction connector.

    NEXT: Go to next step 

  83. CHECK FOR SHORT IN CAN BUS WIRES (REAR MULTIPLEX NETWORK DOOR ECU RH) 
    1. Disconnect the rear multiplex network door ECU RH connector.
      GTY401539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      O3-9 (CANP) - O3-10 (CANN) Engine switch off 54 to 69 Ω
      O3-9 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      O3-10 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      O3-9 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      O3-10 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Rear Multiplex Network Door ECU RH)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO REAR MULTIPLEX NETWORK DOOR ECU RH (CANP, CANN) 

    OK → See step   109 

  84. CONNECT CONNECTOR 
    1. Reconnect the R48 No. 9 junction connector.

    NEXT: Go to next step 

  85. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR) 
    1. Disconnect the No. 8 junction connector.
      GTY403189Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R57-5 (CANH) - R57-7 (CANL) Engine switch off 108 to 132 Ω
      R57-5 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      R57-7 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      R57-5 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      R57-7 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to No. 8 Junction Connector)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR) 

    OK: Go to next step 

  86. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH RH) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY403190Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R57-6 (CANH) - R57-8 (CANL) Engine switch off 200 Ω or higher
      R57-6 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      R57-8 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      R57-6 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      R57-8 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to No. 8 Junction Connector)
      *b Front view of DLC3

    NG → See step   88 

    OK: Go to next step 

  87. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - FRONT CONTROLLER) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY403197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      R57-1 (CANH) - R57-3 (CANL) Engine switch off 108 to 132 Ω
      R57-1 (CANH) - L31-4 (CG) Engine switch off 200 Ω or higher
      R57-3 (CANL) - L31-4 (CG) Engine switch off 200 Ω or higher
      R57-1 (CANH) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      R57-3 (CANL) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to No. 8 Junction Connector)
      *b Front view of DLC3

    NG → See step   90 

    OK → REPLACE NO. 8 JUNCTION CONNECTOR 

  88. CONNECT CONNECTOR 
    1. Reconnect the R57 No. 8 junction connector.

    NEXT: Go to next step 

  89. CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH RH) 
    1. Disconnect the front power seat switch RH connector.
      GTY414953Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      e20-25 (CANP) - e20-24 (CANN) Engine switch off 54 to 69 Ω
      e20-25 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      e20-24 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      e20-25 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      e20-24 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to Front Power Seat Switch RH)
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT POWER SEAT SWITCH RH (CANP, CANN) 

    OK → See step   110 

  90. CONNECT CONNECTOR 
    1. Reconnect the R57 No. 8 junction connector.

    NEXT: Go to next step 

  91. CHECK FOR SHORT IN CAN BUS WIRES (FRONT CONTROLLER) 
    1. Disconnect the front multiplex network light ECU (front controller) connector.
      GTY397686Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) Engine switch off 108 to 132 Ω
      A50-3 (CANP) - L31-4 (CG) Engine switch off 200 Ω or higher
      A50-4 (CANN) - L31-4 (CG) Engine switch off 200 Ω or higher
      A50-3 (CANP) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      A50-4 (CANN) - L31-16 (BAT) Engine switch off 6 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Front Multiplex Network Light ECU [Front Controller])
      *b Front view of DLC3

    NG → REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO FRONT CONTROLLER (CANP, CANN) 

    OK → REPLACE FRONT MULTIPLEX NETWORK LIGHT ECU (FRONT CONTROLLER) 

  92. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY418138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Main Body ECU [Driver Side Junction Block])      		 - -
      NOTE:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Refer to INITIALIZATION [09/2012 - ] .

    2. Disconnect the main body ECU (driver side junction block) connectors.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      DF-1 (ALTB) - Body ground Always 11 to 14 V
      DA-19 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V
      DA-32 (IG) - Body ground Engine switch on (IG) 11 to 14 V
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA-40 (GND1) - Body ground Always Below 1 Ω
      DA-40 (GND2) - Body ground Always Below 1 Ω
      L11-1 (GND3) - DA-41 Always Below 1 Ω

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK) 

  93. REPLACE REAR POWER SEAT SWITCH. Refer to  DISASSEMBLY [09/2012 - ] 
  94. REPLACE REAR POWER SEAT SWITCH. Refer to  REMOVAL [09/2012 - ] 
  95. REPLACE POWER TRUNK LID CONTROL ECU (LUGGAGE CLOSER MOTOR ASSEMBLY). Refer to  REMOVAL [09/2012 - ] 
  96. REPLACE FRONT POWER SEAT SWITCH LH. Refer to  DISASSEMBLY [09/2012 - ] 
  97. REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH. Refer to  REMOVAL [09/2012 - ] 
  98. REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH. Refer to  REMOVAL [09/2012 - ] 
  99. REPLACE DRIVING SUPPORT ECU ASSEMBLY. Refer to  REMOVAL [09/2012 - ] 
  100. REPLACE TIRE PRESSURE WARNING RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2012 - ] 
  101. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [09/2012 - ] 
  102. REPLACE MULTIPLEX TILT AND TELESCOPIC ECU. Refer to  REMOVAL [09/2012 - ] 
  103. REPLACE NO. 1 METER ECU SUB-ASSEMBLY. Refer to  DISASSEMBLY [09/2012 - ] 
  104. REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY. Refer to  REMOVAL [09/2012 - ] 
  105. REPLACE STEERING PAD SWITCH ASSEMBLY (STEERING PAD ECU). Refer to  DISASSEMBLY [09/2012 - ] 
  106. REPLACE SPIRAL CABLE SUB-ASSEMBLY. Refer to  REMOVAL [09/2012 - ] 
  107. REPLACE OUTER MIRROR SWITCH ASSEMBLY. Refer to  REMOVAL [09/2012 - ] 
  108. REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH. Refer to  REMOVAL [09/2012 - ] 
  109. REPAIR REAR MULTIPLEX NETWORK DOOR ECU RH. Refer to  REMOVAL [09/2012 - ] 
  110. REPLACE FRONT POWER SEAT SWITCH RH. Refer to  DISASSEMBLY [09/2012 - ] 
  111. REPLACE REAR POWER SEAT SWITCH. Refer to  REMOVAL [09/2012 - ] 
  112. REPLACE REAR POWER SEAT SWITCH. Refer to  DISASSEMBLY [09/2012 - ] 
scientia non olet · About LEMON Manuals