Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment: Procedure

1. Check that the entry lock and unlock function can be operated at each door. Refer to OPERATION CHECK .

   OK

   entry functions operate normally.

NG → See step   11 

OK: Go to next step 

1. When the luggage compartment door opener switch is operated, check that the luggage compartment door opens. Refer to OPERATION CHECK .

   OK

   Luggage compartment door opens.

NG → See step   12 

OK: Go to next step 

1. Using the Techstream, read the Data List. Refer to DATA LIST / ACTIVE TEST .
   BACK DOOR
   
   

   Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
   Back Door Handle SW	Luggage compartment door opener switch / ON or OFF	ON: Luggage compartment door opener switch is pushed OFF: Luggage compartment door opener switch is not pushed	-

   OK

   On the Techstream screen, item changes between ON and OFF according to above chart.

NG → See step   9 

OK: Go to next step 

1. Bring the electrical key transmitter near the electrical key antenna (in rear bumper), and perform an entry luggage compartment open function check.
   Fig 1: Performing Entry Operational Inspection Luggage Compartment

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   If the key is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.

   HINT: 

   • When the electrical key transmitter is brought near the electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
   • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

   OK

   Entry functions operate normally.

NG → See step   5 

OK → AFFECTED BY WAVE INTERFERENCE 

1. Diagnostic mode inspection (electrical key antenna)
   Fig 2: Identifying Electrical Key Antenna Height (Vehicle Center)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the power switch ON (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Access / Smart Communication Check /Overhead + Luggage.
   5. When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

      HINT: 

      If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

      OK

      Wireless door lock buzzer sounds

NG → See step   6 

OK → See step   15 

Fig 3: Identifying Certification ECU And Electrical Key Antenna Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the L15 ECU connector.
2. Disconnect the R40 antenna connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   L15-31 (CLG8) - R40-1 (CLG5)	Always	Below 1 Ω
   L15-32 (CG8B) - R40-2 (CLGB)	Always	Below 1 Ω
   L15-31 (CLG8) - Body ground	Always	10 kΩ or higher
   L15-32 (CG8B) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Replace the electrical key antenna with a new or normally functioning one. Refer to REMOVAL .
2. Check that the entry luggage compartment open function operates normally. Refer to OPERATION CHECK .

   OK

   Operates normally

NG → See step   8 

OK → END (ELECTRICAL KEY ANTENNA IS DEFECTIVE) 

1. Replace the luggage closer motor with a new or normally functioning one. Refer to REMOVAL .
2. Check that the entry luggage compartment open function operates normally. Refer to OPERATION CHECK .

   OK

   Operates normally

NG → See step   15 

OK → END (LUGGAGE CLOSER MOTOR IS DEFECTIVE) 

Fig 4: Identifying Luggage Compartment Door Opener Switch Connector Terminal

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Switch Condition	Specified Condition
   1 - 2	OFF	Below 1 Ω
   1 - 2	ON	10 kΩ or higher

NG → See step   13 

OK: Go to next step 

Fig 5: Identifying Luggage Closer Motor And Luggage Compartment Door Opener Switch Connector Terminal

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the S43 ECU connector.
2. Disconnect the S38 switch connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   S38-1 - Body ground	Always	Below 1 Ω
   S43-19 (LPSW) - S38-2	Always	Below 1 Ω
   S38-2 - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   14