LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2009 >> LS 600hL >> Repair and Diagnosis >> External Pages >> Different car >> Section 49 (Sliding Roof) >> Sliding Roof System >> Operation Check

Operation Check

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Perform initialization before performing the operation check.
  1. CHECK AUTO OPERATION 
    1. Turn the power switch ON (IG).
    2. When the roof glass is fully closed, press the SLIDE OPEN switch for 0.3 seconds or more Check that the roof glass automatically slides until it is fully opened
    3. When the roof glass is fully open, press the SLIDE CLOSE switch for 0.3 seconds or more. Check that the roof glass automatically slides until it is fully closed.
    4. When the roof glass is fully closed, press the TILT UP switch for 0 3 seconds or more. Check that the roof glass automatically tilts until it is fully tilted up.
    5. When the roof glass is fully up, press the TILT DOWN switch for 0.3 seconds or more Check that the roof glass automatically tilts until it is fully tilted down.
    6. When the AUTO operation is operating, check that pressing any sliding roof switch stops the roof glass operation.

      HINT

      When pressing the switch for less than 0.3 seconds, the roof glass moves but AUTO operation does not operate.

  2. CHECK SLIDING ROOF OPERATION AFTER POWER SWITCH IS TURNED OFF 
    1. Turn the power switch from ON (IG) to OFF, and check that the sliding roof operates Then open the driver side door once, and check that the sliding roof does not operate
    2. Turn the power switch from ON (IG) to OFF and wait for approximately 45 seconds Check that the sliding roof does not operate.
    3. Operate the AUTO (SLIDE OPEN / CLOSE or TILT UP / DOWN) operation While the roof glass is in motion, turn the power switch from ON (IG) to OFF Check that the AUTO operation continues until the roof glass opens or closes fully

      HINT

      When the driver door opens, the sliding roof operation will stop

  3. CHECK JAM PROTECTION FUNCTION 
    CAUTION:
    • Do not use a part of your body, for example, your hand, to check the jam protection.
    • Do not allow anything to become caught in the sliding roof by accident in this procedure.
    • Perform the inspection from the inside of the vehicle.
    NOTE:
    • Do not use hard objects, such as a hammer, to avoid damage to the roof.
    • If the jam protection does not operate, initialize the sliding roof drive gear (motor).
    1. When the sliding roof AUTO close operation is operating and an object is caught between the vehicle body and glass, check that the roof glass opens a distance of 218 mm (8.58 in.) from the point of contact with the object, or opens fully if an opening distance of 218 mm (8.58 in.) is not available
      Fig 1: Identifying Roof Glass Opens Position
      G04953264Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. When the AUTO TILT DOWN function is operating, and an object is caught between the vehicle body and the roof glass, check that the sliding roof tilts up fully.
    3. Fig 2: Identifying Sliding Roof Tilts Up Fully
      G04953265Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. CHECK TRANSMITTER-LINKED OPEN OPERATION FUNCTION 
    1. Close all the doors
    2. Hold down the transmitter's UNLOCK switch for approximately 3 seconds or more and check that the SLIDE OPEN / TILT UP operation occurs. Also, when the UNLOCK switch is released, check that the roof glass stops moving
  5. CHECK KEY-LINKED OPEN / CLOSE OPERATION FUNCTION (DRIVERS DOOR ONLY) 
    1. Insert the key into the driver side door's key lock cylinder, and turn the key to the unlock position for approximately 3 seconds or more Check that the sliding roof starts moving (SLIDE OPEN / TILT UP operation). Then release the key and check that the sliding roof stops moving.
    2. Insert the key into the driver side door's key lock cylinder, and turn the key to the lock position for approximately 3 seconds or more. Check that the sliding roof starts moving (SLIDE CLOSE / TILT DOWN operation) Then release the key and check that the sliding roof stops moving
  6. CHECK ENTRY LOCK SWITCH-LINKED CLOSE OPERATION FUNCTION 
    1. Close all the doors, open the roof glass and check that the key is not in the vehicle.
    2. When the entry lock switch on the door outside handle is pressed for 3 seconds or more, check that the roof glass closes. Also, when the entry lock switch is released, check that the roof glass stops operating