LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2009 >> LS 600hL >> Repair and Diagnosis >> External Pages >> Different car >> Section 24 (Suspension) >> Front Active Stabilizer Control Actuator >> Removal

Front Active Stabilizer Control Actuator: Removal

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY  (See REMOVAL )
  2. REMOVE BATTERY SERVICE HOLE COVER LH  (See REMOVAL )
  3. REMOVE BATTERY SERVICE HOLE COVER  (See REMOVAL )
  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
    NOTE:
    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see INITIALIZATION ).
    • After the power switch is turned OFF, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the power switch OFF, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.
  5. REMOVE SERVICE PLUG GRIP  (See REMOVAL )
  6. REMOVE FRONT CENTER FLOOR COVER  (See REMOVAL )
  7. REMOVE NO. 2 ENGINE UNDER COVER  (See REMOVAL )
  8. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH  (See REMOVAL )
  9. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH  (See REMOVAL )
  10. REMOVE NO. 1 ENGINE UNDER COVER  (See REMOVAL )
  11. REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR  (See REMOVAL )
  12. REMOVE FRONT STABILIZER LINK ASSEMBLY LH 
    1. Remove the 2 nuts and front stabilizer link.
      Fig 1: Locating Front Stabilizer Link Assembly Nuts
      G05781534Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.

  13. REMOVE FRONT STABILIZER LINK ASSEMBLY RH 

    HINT:

    Remove the RH side following the same procedures as the LH side.

  14. REMOVE FRONT FENDER WHEEL OPENING MOLDING LH  (See REMOVAL )
  15. REMOVE FRONT FENDER LINER LH  (See REMOVAL )
  16. DISCONNECT FRONT ACTIVE STABILIZER CONTROL ACTUATOR CONNECTOR 
    1. Disconnect the wire harness clamp.
    2. Disconnect the actuator connector labeled A.
    3. Disconnect the actuator connector labeled B.
      1. Release the lever's lock. (*1)
      2. Press the claw and move the lever in the direction of the arrow in the illustration (*2)
      3. Disconnect the actuator connector (*3)
        NOTE: When disconnecting the actuator connector, do not apply excessive force to the wire harness.
        Fig 2: Locating Actuator Connector
        G05773892Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE FRONT NO. 1 STABILIZER BRACKET LH 
    1. Remove the bolt and wire harness bracket.
      Fig 3: Locating Wire Harness Bracket With Bolt
      G05781672Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly
      Fig 4: Locating Front No. 1 Stabilizer Bracket With Bolts
      G05781585Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE FRONT NO. 1 STABILIZER BRACKET RH 
    1. Remove the bolts and disconnect water with motor and bracket pump bracket.
      Fig 5: Locating Front No. 1 Stabilizer Bracket Bolt
      G05781674Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 bolts and front No 1 stabilizer bracket RH from the front frame assembly
      Fig 6: Identifying Front No. 1 Stabilizer Bracket With Bolts
      G05781604Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE FRONT ACTIVE STABILIZER CONTROL ACTUATOR ASSEMBLY 
    1. Remove the front active stabilizer control actuator from the vehicle.
  20. REMOVE FRONT NO. 1 STABILIZER BAR BUSH 
    1. Remove the 2 front No 1 stabilizer bar bushes from the front active stabilizer control actuator