Data List / Active Test

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.

DATA LIST

HINT.

Using the Intelligent tester or Techstream to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

Warm up the engine
Turn the power switch OFF.
Connect the Intelligent tester or Techstream to the DLC3.
Turn the power switch ON (IG).
Turn the tester on.
Enter the following menus.
1. Intelligent tester - Select. DIAGNOSIS / OBD/ MOBD / SMART ACCESS / DATA LIST
2. Techstream - Select. Body Electrical / Smart Access / Data List

According to the display on tester, read the "Data List"

Intelligent tester

SMART ACCESS

DIAGNOSTIC NOTE

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
#CODES	Number of diagnosis codes	-	-
SENSOR VALUE	Sensor malfunction/NG (Past) or OK	NG (Past) Sensor malfunction OK No malfunction	-
PWR SUPPLY SHRT	Short in ECU/NG (Past) or OK	NG (Past) Short in ECU OK No malfunction	-
PWR SUPPLY OPEN	Open in ECU/NG (Past) or OK	NG (Past) Open in ECU OK No malfunction	-
MTR DRIVER SHRT	Short in driver ECU/NG (Past) or OK	NG (Past) Short in driver ECU OK No malfunction	-
MTR DRIVER OPEN	Open in driver ECU/NG (Past) or OK	NG (Past) Open in driver ECU OK No malfunction	-
LCK/UNLCK REC	Steering lock command reception record/ YES or NO	YES Steering lock / unlock signal received NO Steering lock / unlock signal not received	-
LCK BAR STUCK	Lock bar stuck malfunction/NG (Past) or OK	NG (Past) Lock bar stuck malfunction OK No malfunction	-
PUSH START ERR	Push button start function malfunction/NG (Past) or OK	NG (Past) Malfunction in push button start OK No malfunction	-
IG2	IG2 voltage/ON or OFF	ON 11 to 14 V OFF Below 1 V	-
IG (LIN)	LIN bus start-up status/ON or OFF	ON LIN bus started-up OFF LIN bus not started-up	-
S CODE CHK	S code match record/NG or OK	NG S code not matched OK S code matched	-
L CODE CHK	L code match record/NG or OK	NG L code not matched OK L code matched	-
UNLC RQ RECEIVE	Steering lock unlock command reception status/NG or OK	NG Unlock request not received OK Unlock request received	-
LCK RQ RECEIVE	Steering lock lock command reception status/NG or OK	NG Lock request not received OK Lock request received	-
S CODE CHK-PAST	S code match record/NG (Past) or OK	NG (Past) S code not matched OK S code matched	-
L CODE CHK-PAST	L code match record/NG (Past) or OK	NG (Past) L code not matched OK L code matched	-
STEERING LOCK	Steering lock condition/Set or Unset	Set Steering lock is set Unset Steering lock is not set	This status changes depending on the state of various sensors
STEERING UNLOCK	Steering unlock condition/Set or Unset	Set Steering unlock is set Unset Steering unlock is not set	This status changes depending on the state of various sensors

Techstream

Smart Access

DIAGNOSTIC NOTE

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
#Codes	Number of diagnosis codes	-	-
Sensor Value	Sensor malfunction/NG (Past) or OK	NG (Past) Sensor malfunction OK No malfunction	-
Power Supply Short	Short in ECU/NG (Past) or OK	NG (Past) Short in ECU OK No malfunction	-
Power Supply Open	Open in ECU/NG (Past) or OK	NG (Past) Open in ECU OK No malfunction	-
Motor Driver Short	Short in driver ECU/NG (Past) or OK	NG (Past) Short in driver ECU OK No malfunction	-
Motor Driver Open	Open in driver ECU/NG (Past) or OK	NG (Past) Open in driver ECU OK No malfunction	-
Lock / Unlock Receive	Steering lock command reception record/ YES or NO	YES Steering lock / unlock signal received NO Steering lock / unlock signal not received	-
Lock Bar Stuck Error	Lock bar stuck malfunction/NG (Past) or OK	NG (Past) Lock bar stuck malfunction OK No malfunction	-
Push Start Error	Push button start function malfunction/NG (Past) or OK	NG (Past) Malfunction in push button start OK No malfunction	-
IG2 Status	IG2 voltage/ON or OFF	ON 11 to 14 V OFF Below 1 V	-
IG (Lin)	LIN bus start-up status/ON or OFF	ON LIN bus started-up OFF LIN bus not started-up	-
S Code Check	S code match record/NG or OK	NG S code not matched OK S code matched	-
L Code Check	L code match record/NG or OK	NG L code not matched OK L code matched	-
Unlock Request Receive	Steering lock unlock command reception status/NG or OK	NG Unlock request not received OK Unlock request received	-
Lock Request Receive	Steering lock lock command reception status/NG or OK	NG Lock request not received OK Lock request received	-
S Code Check (Past)	S code match record/NG (Past) or OK	NG (Past) S code not matched OK S code matched	-
L Code Check (Past)	L code match record/NG (Past) or OK	NG (Past) L code not matched OK L code matched	-
Steering Lock	Steering lock condition/Set or Unset	Set Steering lock is set Unset Steering lock is not set	This status changes depending on the state of various sensors
Steering Unlock	Steering unlock condition/Set or Unset	Set Steering unlock is set Unset Steering unlock is not set	This status changes depending on the state of various sensors