LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2009 >> LS 460L AWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat >> Front Power Seat Control System >> DTC B2650 Slide Sensor Malfunction >> Inspection Procedure

Inspection Procedure

  1. CHECK FOR DTC 
    1. Check for DTCs.
      1. Using the Techstream, check which ECU output the DTC.

        Result 

        RESULT CHART

        Result Proceed to
        B2650 output from driver seat ECU A
        B2650 output from passenger seat ECU B

        B:  Go to step  9

        A: Go to next step 

  2. PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR FUNCTION) 
    1. Select the Active Test, use the Techstream to generate a control command, and then check the power seat motor function.

      Driver Seat 

      DIAGNOSTIC NOTE

      Tester Display Test Part Control Range Diagnostic Note
      Seat Slide Operation Seat sliding operation FRONT/REAR -

      OK: 

      Motor operates normally. 

      NG:  Go to step  7

      OK: Go to next step 

  3. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT POWER SEAT POSITION SENSOR LH) 
    1. Disconnect the e46 switch connector.
    2. Disconnect the e36 sensor connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      e46-8 (PVCC) - e36-3 (VCC) Always Below 1 Ω
      e46-23 (SSRS) - e36-1 (O/P) Always Below 1 Ω
      e46-18 (SGND) - e36-2 (GND) Always Below 1 Ω
      e46-8 (PVCC) - Body ground Always 10 kΩ or higher
      e46-23 (SSRS) - Body ground Always 10 kΩ or higher
      e46-18 (SGND) - Body ground Always 10 kΩ or higher
      Fig 1: Checking Harness And Connector (Front Power Seat Switch LH - Front Power Seat Position Sensor LH)
      G04952424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

      OK: Go to next step 

  4. CHECK FRONT POWER SEAT SWITCH LH 
    1. Disconnect the e36 sensor connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      e36-3 (VCC) - e36-2 (GND) Sliding switch signal ON 7.2 to 8.8 V
      Fig 2: Identifying e36 Sensor Connector Terminals
      G04952425Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPLACE FRONT POWER SEAT SWITCH LH (See  REMOVAL   ) 

      OK: Go to next step 

  5. CHECK FRONT SEAT ADJUSTER ASSEMBLY LH (POSITION CONTROL SENSOR) 
    1. Reconnect the e36 sensor connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      e36-1 (O/P) - Body ground Sliding switch signal ON 0 to 8 V
      Fig 3: Identifying e36 Sensor Connector Terminals
      G06194126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (See  REMOVAL   ) 

      OK: Go to next step 

  6. CHECK FOR DTC 
    1. Clear the DTCs (see DTC CHECK/CLEAR  ).
    2. Recheck for DTCs.

      OK: 

      DTC B2650 is not output. 

      NG: REPLACE FRONT POWER SEAT SWITCH LH (See  REMOVAL   ) 

      OK: END (SYSTEM RETURNS TO NORMAL) 

  7. CHECK FRONT SEAT ADJUSTER ASSEMBLY LH (POWER SEAT MOTOR) 
    1. Check the operation of the power seat motor (slide motor).
      1. Check if the seat adjuster moves smoothly when the battery is connected to the slide motor connector terminals.

        OK 

        MEASUREMENT CONDITION CHART

        Measurement Condition Operation Direction
        Battery positive (+) → 2
        Battery negative (-) → 1        		 Seat adjuster moves forward
        Battery positive (+) → 1
        Battery negative (-) → 2        		 Seat adjuster moves backward
        Fig 4: Identifying Power Seat Motor Connector Terminals
        G06194127Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        NG: REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (See  REMOVAL   ) 

        OK: Go to next step 

  8. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POWER SEAT MOTOR) 
    1. Disconnect the e46 switch connector.
    2. Disconnect the e37 motor connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      e46-12 (SLD+) - e37-2 Always Below 1 Ω
      e46-11 (SLD-) - e37-1 Always Below 1 Ω
      Fig 5: Checking Harness And Connector (Front Power Seat Switch LH - Power Seat Motor)
      G04952428Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

      OK: REPLACE FRONT POWER SEAT SWITCH LH (See  REMOVAL   ) 

  9. PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR FUNCTION) 
    1. Select the Active Test, use the Techstream to generate a control command, and then check the power seat motor function.

      Passenger Seat 

      DIAGNOSTIC NOTE

      Tester Display Test Part Control Range Diagnostic Note
      Seat Slide Operation Seat sliding operation FRONT/REAR -

      OK: 

      Motor operates normally. 

      NG:  Go to step  14

      OK: Go to next step 

  10. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - FRONT POWER SEAT POSITION SENSOR RH) 
    1. Disconnect the e20 switch connector.
    2. Disconnect the e5 sensor connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      e20-8 (PVCC) - e5-3 (VCC) Always Below 1 Ω
      e20-23 (SSRS) - e5-1 (O/P) Always Below 1 Ω
      e20-18 (SGND) - e5-2 (GND) Always Below 1 Ω
      e20-8 (PVCC) - Body ground Always 10 kΩ or higher
      e20-23 (SSRS) - Body ground Always 10 kΩ or higher
      e20-18 (SGND) - Body ground Always 10 kΩ or higher
      Fig 6: Checking Harness And Connector (Front Power Seat Switch RH - Front Power Seat Position Sensor RH)
      G04952429Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

      OK: Go to next step 

  11. CHECK FRONT POWER SEAT SWITCH RH 
    1. Disconnect the e5 sensor connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      e5-3 (VCC) - e5-2 (GND) Sliding switch signal ON 7.2 to 8.8 V
      Fig 7: Identifying e5 Sensor Connector Terminals
      G04952430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPLACE FRONT POWER SEAT SWITCH RH (See  REMOVAL   ) 

      OK: Go to next step 

  12. CHECK FRONT SEAT ADJUSTER ASSEMBLY RH (POSITION CONTROL SENSOR) 
    1. Reconnect the e5 sensor connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      e5-1 (O/P) - Body ground Sliding switch signal ON 0 to 8 V
      Fig 8: Identifying e5 Sensor Connector Terminals
      G06194131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (See  REMOVAL   ) 

      OK: Go to next step 

  13. CHECK FOR DTC 
    1. Clear the DTCs (see DTC CHECK/CLEAR  ).
    2. Recheck for DTCs.

      OK: 

      DTC B2650 is not output. 

      NG: REPLACE FRONT POWER SEAT SWITCH RH (See  REMOVAL   ) 

      OK: END (SYSTEM RETURNS TO NORMAL) 

  14. CHECK FRONT SEAT ADJUSTER ASSEMBLY RH (POWER SEAT MOTOR) 
    1. Check the operation of the power seat motor (slide motor).
      1. Check if the seat adjuster moves smoothly when the battery is connected to the slide motor connector terminals.

        OK 

        MEASUREMENT CONDITION CHART

        Measurement Condition Operation Direction
        Battery positive (+) → 1
        Battery negative (-) → 2        		 Seat adjuster moves forward
        Battery positive (+) → 2
        Battery negative (-) → 1        		 Seat adjuster moves backward
        Fig 9: Identifying Power Seat Motor Connector Terminals
        G04952427Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        NG: REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (See  REMOVAL   ) 

        OK: Go to next step 

  15. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - POWER SEAT MOTOR) 
    1. Disconnect the e20 switch connector.
    2. Disconnect the e6 motor connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      e20-12 (SLD+) - e6-1 Always Below 1 Ω
      e20-11 (SLD-) - e6-2 Always Below 1 Ω
      Fig 10: Checking Harness And Connector (Front Power Seat Switch RH - Power Seat Motor)
      G04952433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

      OK: REPLACE FRONT POWER SEAT SWITCH RH (See  REMOVAL   ) 

scientia non olet · About LEMON Manuals