LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2009 >> LS 460 RWD >> Repair and Diagnosis >> Accessories & Equipment >> Interior/Illumination Lights >> Lighting >> Automatic Light Control Sensor >> Removal

Automatic Light Control Sensor: Removal

  1. TABLE OF BOLT, SCREW AND NUT  (See REMOVAL )
  2. REMOVE COWL TOP VENTILATOR LOUVER RH  (See REMOVAL )
  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    1. Disable the AUTO TILT AWAY function by changing the customize parameter (see CUSTOMIZE PARAMETERS ).
      NOTE: Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.

      HINT:

      Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.
    3. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.
      CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
      NOTE: After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.
  4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH  (See REMOVAL )
  5. REMOVE INSTRUMENT PANEL FINISH PANEL END LH  (See REMOVAL )
  6. REMOVE SHIFT LEVER KNOB  (See REMOVAL )
  7. REMOVE NO. 3 BOX PANEL  (See REMOVAL )
  8. REMOVE REAR CONSOLE PANEL UPPER  (See REMOVAL )
  9. REMOVE CONSOLE PANEL SUB-ASSEMBLY UPPER  (See REMOVAL )
  10. REMOVE CONSOLE REAR END PANEL  (See REMOVAL )
  11. REMOVE CONSOLE COVER LOWER  (See REMOVAL )
  12. REMOVE CONSOLE BOX ASSEMBLY  (See REMOVAL )
  13. REMOVE SWITCH AND VOLUME CASE  (See REMOVAL )
  14. REMOVE NO. 2 STEERING WHEEL COVER LOWER  (See REMOVAL )
  15. REMOVE STEERING PAD ASSEMBLY  (See REMOVAL )
  16. REMOVE STEERING WHEEL ASSEMBLY  (See REMOVAL )
  17. REMOVE STEERING COLUMN COVER (w/o Driver Monitor Camera)  (See REMOVAL )
  18. REMOVE STEERING COLUMN COVER (w/ Driver Monitor Camera)  (See REMOVAL )
  19. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE  (See REMOVAL )
  20. REMOVE INSTRUMENT CLUSTER FINISH PANEL  (See REMOVAL )
  21. REMOVE COMBINATION METER ASSEMBLY  (See REMOVAL )
  22. REMOVE INSTRUMENT SIDE PANEL LH  (See REMOVAL )
  23. REMOVE NO. 1 INSTRUMENT CLUSTER MOLDING  (See REMOVAL )
  24. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER  (See REMOVAL )
  25. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD  (See REMOVAL )
  26. REMOVE NO. 1 INSTRUMENT PANEL LOWER AIRBAG  (See REMOVAL )
  27. REMOVE INSTRUMENT SIDE PANEL RH  (See REMOVAL )
  28. REMOVE NO. 2 INSTRUMENT CLUSTER  (See REMOVAL )
  29. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER  (See REMOVAL )
  30. REMOVE INSTRUMENT PANEL LOWER  (See REMOVAL )
  31. REMOVE NO. 2 INSTRUMENT PANEL LOWER AIRBAG  (See REMOVAL )
  32. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (See  REMOVAL  ) 
  33. REMOVE RADIO RECEIVER ASSEMBLY  (See REMOVAL )
  34. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Navigation System)  (See REMOVAL )
  35. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET (for DVD)  (See REMOVAL )
  36. REMOVE DISPLAY AND NAVIGATION ASSEMBLY WITH BRACKET (for HDD)  (See REMOVAL )
  37. REMOVE FRONT PILLAR GARNISH RH  (See REMOVAL )
  38. REMOVE FRONT PILLAR GARNISH LH  (See REMOVAL )
  39. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL  (See REMOVAL )
  40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH)  (See REMOVAL )
  41. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL  (See REMOVAL )
  42. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH)  (See REMOVAL )
  43. REMOVE NO. 1 SPEAKER HOLE COVER  (See REMOVAL )
  44. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY  (See REMOVAL )
  45. REMOVE TIRE PRESSURE WARNING ECU  (See DISASSEMBLY )
  46. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY  (See REMOVAL )
  47. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY  (See REMOVAL )
  48. REMOVE INSTRUMENT PANEL SAFETY PAD  (See REMOVAL )
  49. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT  (See DISASSEMBLY )
  50. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT  (See DISASSEMBLY )
  51. REMOVE DEFROSTER NOZZLE ASSEMBLY  (See DISASSEMBLY )
  52. REMOVE AUTOMATIC LIGHT CONTROL SENSOR 
    1. Disconnect the connector.
    2. Detach the 2 claws and remove the automatic light control sensor.
      Fig 1: Identifying Automatic Light Control Sensor Claws
      G04944993Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals