LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> SC 430 >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior >> Roof Headlining >> Disassembly

Roof Headlining: Disassembly

  1. OPEN ROOF PANEL HALFWAY 
    1. Open the roof panel halfway (see MANUAL OPEN OPERATION ).
      Fig 1: Opening Roof Panel Halfway
      G05293957Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH 
    1. Using a clip remover, detach the 5 clips.
    2. Using a screwdriver, detach the 6 claws and remove the scuff plate.

      HINT:

      Tape the screwdriver tip before use.

      Fig 2: Identifying Claws And Scuff Plate
      G05293958Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH 

    HINT:

    Use the same procedures described for the RH side.

  4. REMOVE FRONT DOOR OPENING TRIM COVER RH 
    1. Using a screwdriver, detach the 3 claws and remove the trim cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 3: Identifying Claws And Trim Cover
      G05293959Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FRONT DOOR OPENING TRIM COVER LH 

    HINT:

    Use the same procedures described for the RH side.

  6. REMOVE FRONT PILLAR GARNISH RH 
    1. Using a screwdriver, detach the 2 clips and remove the garnish.

      HINT:

      Tape the screwdriver tip before use.

      Fig 4: Identifying Clips And Garnish
      G05293960Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE FRONT PILLAR GARNISH LH 

    HINT:

    Use the same procedures described for the RH side.

  8. REMOVE VISOR BRACKET COVER RH 
    1. Using a screwdriver, detach the 3 claws and remove the bracket cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 5: Identifying Bracket Cover Claws
      G05293961Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE VISOR BRACKET COVER LH 

    HINT:

    Use the same procedures described for the RH side.

  10. REMOVE VISOR ASSEMBLY RH 
    1. Remove the 2 screws and visor.
  11. REMOVE VISOR ASSEMBLY LH 
    1. Remove the 2 screws and visor.
  12. REMOVE VISOR HOLDER 
    1. Remove the 2 holders by turning them counterclockwise.
      Fig 6: Turning Visor Holders Counterclockwise
      G05293962Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE MAP LIGHT ASSEMBLY 
    1. Using a screwdriver, pry out the 2 lenses.

      HINT:

      Tape the screwdriver tip before use.

    2. Remove the 2 screws and map light.
    3. Disconnect the map light connector.
      Fig 7: Identifying Screws And Map Light
      G05293963Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE ROOF FRONT CORNER HEADLINING RH 
    1. Using a screwdriver, detach the 2 clips and remove the headlining.

      HINT:

      Tape the screwdriver tip before use.

      Fig 8: Identifying Clips And Headlining
      G05293964Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE ROOF FRONT CORNER HEADLINING LH 

    HINT:

    Use the same procedures described for the RH side.

  16. REMOVE ROOF HEADLINING ASSEMBLY 
    1. Using a clip remover, remove the 2 clips.
      Fig 9: Identifying Roof Headlining Assembly Clips
      G05293965Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pull the headlining as indicated by the arrow in the illustration, to detach the 4 claws. Then remove the headlining.
      Fig 10: Identifying Headlining
      G05293966Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH 
    1. Using a screwdriver, detach the 4 clips and 3 claws. Then remove the garnish.

      HINT:

      Tape the screwdriver tip before use.

      Fig 11: Identifying Clips And Claws
      G05293967Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH 

    HINT:

    Use the same procedures described for the RH side.

  19. REMOVE ROOF HEADLINING ASSEMBLY CENTER 
    1. Using a clip remover, remove the 5 clips.
    2. Using a screwdriver, detach the 3 clips labeled A and remove the headlining.

      HINT:

      Tape the screwdriver tip before use.

      Fig 12: Identifying Roof Headlining Assembly Center Clips
      G05293968Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE ROOF SIDE GARNISH INNER RH 
    1. Using a clip remover, remove the clip labeled A.
    2. Using a screwdriver, detach the 7 clips and claw. Then remove the garnish.

      HINT:

      Tape the screwdriver tip before use.

      Fig 13: Identifying Roof Side Garnish Inner Clips And Claw
      G05293969Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE ROOF SIDE GARNISH INNER LH 

    HINT:

    Use the same procedures described for the RH side.

  22. REMOVE ROOF HEADLINING ASSEMBLY REAR 
    1. Using a screwdriver, detach the 7 clips and remove the headlining.

      HINT:

      Tape the screwdriver tip before use.

      Fig 14: Identifying Clips And Headlining
      G05293970Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals