Engine Immobilizer System: Registration
- DESCRIPTION OF CODE REGISTRATION
HINT:
- The engine immobilizer function ID code is the same as the recognition code for the smart access system with push-button start and wireless transmitter. Registering an ID code enables the smart access system with push-button start, wireless door lock control function and engine immobilizer function to be operated.
- Code registration is needed when the certification ECU (smart key ECU assembly), ID code box (immobilizer code ECU), steering lock ECU, ECM or key is replaced with a new one
- This vehicle does not have a key slot. Therefore, touch the logo of the key to the engine switch to register the key, as shown in the illustration.
- PART REPLACEMENT AND KEY REGISTRATION PROCEDURES
- If a malfunctioning ECU is discovered through troubleshooting of the smart access system with push-button start, use the ECU replacement and key registration procedures in the table below.
HINT:
- The following procedures require the use of the Techstream:
- New key ID registration
- Additional key ID registration
- Key ID erasure
- ECU code registration
- When simply adding a new key (without losing or replacing any existing keys), refer to c"Additional key ID registration" under Key Registration Procedures.
- If all of the registered keys are not available, replacement of the ID code box (immobilizer code ECU), certification ECU (smart key ECU assembly) and steering lock ECU is also required.
- A maximum of 7 keys can be registered.
PROCEDURE CHARTPart to be Replaced Condition Procedure Certification ECU (smart key ECU assembly) Customer has brought all keys - Replace certification ECU (smart key ECU assembly)
- Reregister all keys (new key ID registration)
Some keys are lost Key ID codes can be registered not cleared - Clear key codes (key ID erasure)
- Perform additional key registration procedure (additional key ID registration)
- Replace certification ECU (smart key ECU assembly)
- Reregister all keys (new key ID registration)
HINT
If some keys are not registered during above steps, they will be disabled because they cannot be registered laterKey ID codes cannot be either registered or cleared - Replace certification ECU (smart key ECU assembly)
- Replace ID code box (immobiliser code ECU)
- Reregister all keys (new key ID registration)
HINT
If key codes cannot be cleared or additional keys cannot be registered due to malfunction in certification ECU (smart key ECU assembly), replace ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) If some keys are not registered during above steps, they will be disabled because they cannot be registered laterAll keys are lost - Replace certification ECU (smart key ECU assembly)
- Replace ID code box (immobiliser code ECU)
- Replace steering lock ECU
- Register all keys (new key ID registration)
- ECU communication ID registration
ID code box (immobiliser code ECU) At least 1 key is available - Replace ID code box (immobiliser code ECU)
- ECU communication ID registration
All keys are lost - Replace ID code box (immobiliser code ECU)
- Replace certification ECU (smart key ECU assembly)
- Replace steering lock ECU
- Register all keys (new key ID registration)
- ECU communication ID registration
Steering lock ECU Customer has brought at least 1 key - Replace steering lock ECU
- Register recognition codes in ECUs (ECU code registration)
All keys are lost - Replace certification ECU (smart key ECU assembly)
- Replace ID code box (immobiliser code ECU)
- Replace steering lock ECU
- Register all keys (new key ID registration)
- ECU communication ID registration
Main body ECU No condition required Replace main body ECU ECM No condition required - Replace ECM
- ECU communication ID registration
HINT
Only perform procedure above when replacing with used ECMKey Customer has brought at least 1 key
HINT
After key ID erasure, any remaining keys that are not registered at this time cannot be used Therefore, after key ID erasure, register all remaining keys- Using remaining key, clear lost key (key ID erasure)
- Register additional keys as necessary (additional key ID registration)
All keys are lost - Replace certification ECU (smart key ECU assembly)
- Replace ID code box (immobiliser code ECU)
- Replace steering lock ECU
- Register all keys (new key ID registration)
- ECU communication ID registration
- The following procedures require the use of the Techstream:
- If a malfunctioning ECU is discovered through troubleshooting of the smart access system with push-button start, use the ECU replacement and key registration procedures in the table below.
- KEY REGISTRATION PROCEDURES
- New key ID registration (when replacing certification ECU (smart key ECU assembly) and ID code box (immobilizer code ECU), or certification ECU (smart key ECU assembly), ID code box (immobilizer code ECU) and steering lock ECU):PROCEDURE CHART
Process Procedure 1 Start of registration - Connect the Techstream to DLC3
- Turn the engine switch on (IG)
HINT
The engine switch cannot be turned on (IG) more than 10 times To continue the key registration procedure with the engine switch off, after connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at intervals of 1 5 seconds
- Turn the Techstream on
- Enter the following menus. Smart Access / Utility / Key Code Registration
2 Confirmation of ECU code Perform operation according to prompts on the Techstream screen
HINT
Mode is automatically selected by the Techstream (new registration mode or add mode)3 Verification of unregistered key* - Touch logo of unregistered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
- Place unregistered key on front passenger side seat
- Confirm that wireless door lock buzzer sounds once (short beep)
4 Registration of ID code Perform operation according to prompts on the Techstream screen 5 End of registration Finish new key ID code registration HINT:
*: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys has not been finished within the specified time, perform the registration from process 1 again. Make sure that only 1 key is in the cabin during registration. If 2 or more keys are in the cabin simultaneously, the electric waves will interfere with each other, preventing normal registration. - New key ID registration (when replacing certification ECU (smart key ECU assembly)):PROCEDURE CHART
Process Procedure 1 Start of registration - Connect the Techstream to DLC3
- Turn the engine switch on (IG)
HINT
The engine switch cannot be turned on (IG) more than 10 times To continue the key registration procedure with the engine switch off, after connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at intervals of 1 5 seconds
- Turn the Techstream on
- Enter the following menus Smart Access / Utility / Key Code Registration
2 Confirmation of ECU code Perform operation according to prompts on the Techstream screen
HINT
Mode is automatically selected by the Techstream (new registration mode or add mode)3 Confirmation of all registered keys*1 - Touch logo of registered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
4 Confirmation of ECU code Perform operation according to prompts on the Techstream screen 5 Verification of unregistered key*2 - Touch logo of unregistered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
- Place unregistered key on front passenger side seat
- Confirm that wireless door lock buzzer sounds once (short beep)
6 Registration of ID code Perform operation according to prompts on the Techstream screen 7 End of registration Finish new key ID code registration HINT: - *1: Repeat this process for each key registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys has not been finished within the specified time, perform the registration from process 1 again When performing the key confirmation procedure for a key, the security indicator light comes on and remains on until all the keys are confirmed.
- *2: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys has not been finished within the specified time, perform the registration from process 1 again. Make sure that only 1 key is in the cabin during registration. If 2 or more keys are in the cabin simultaneously, the electric waves will interfere with each other, preventing normal registration.
- Additional key ID registration:PROCEDURE CHART
Process Procedure 1 Start of registration - Connect the Techstream to DLC3
- Turn the engine switch on (IG)
HINT
The engine switch cannot be turned on (IG) more than 10 times To continue the key registration procedure with the engine switch off, after connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at intervals of 1 5 seconds
- Turn the Techstream on
- Enter the following menus Smart Access / Utility / Key Code Registration
2 Confirmation of registered key*1 - Perform operation according to prompts on the Techstream screen
- Touch logo of registered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
3 Confirmation of ECU code Perform operation according to prompts on the Techstream screen 4 Verification of unregistered key*2 - Touch logo of unregistered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
- Place unregistered key on front passenger side seat
- Confirm that wireless door lock buzzer sounds once (short beep)
5 Registration of ID code Perform operation according to prompts on the Techstream screen 6 End of registration Finish key ID code registration HINT: - *1: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure has not been finished within the specified time, perform the registration from process 1 again.
- *2: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys has not been finished within the specified time, perform the registration from process 1 again. Make sure that only 1 key is in the cabin during registration. If 2 or more keys are in the cabin simultaneously, the electric waves will interfere with each other, preventing normal registration.
- Key ID erasure (clear all registered key codes except one):PROCEDURE CHART
Process Procedure 1 Start of erasure - Connect the Techstream to DLC3
- Turn the engine switch on (IG)
HINT
The engine switch cannot be turned on (IG) more than 10 times To continue the key ID erasure procedure with the engine switch off, after connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at intervals of 1 5 seconds
- Turn the Techstream on
- Enter the following menus Smart Access / Utility / Key Code Erasure
2 Confirmation of registered key* - Perform operation according to prompts on the Techstream screen
- Touch logo of registered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
3 Erasure of ID code Perform operation according to prompts on the Techstream screen 4. End of erasure Finish key ID code erasure HINT:
*: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure has not been finished within the specified time, perform the erasure from process 1 again. - All keys ID erasure:PROCEDURE CHART
Process Procedure 1 Start of erasure - Connect the Techstream to DLC3
- Turn the engine switch on (IG)
HINT
The engine switch cannot be turned on (IG) more than 10 times To continue all keys ID erasure procedure with the engine switch off, after connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at intervals of 1 5 seconds
- Turn the Techstream on
- Enter the following menus Smart Access / Utility / Key Code Reset
- Read "Seed Number" sent from TIS according to the Techstream screen
2 Confirmation of registered key* Touch logo of registered key to engine switch 3 Erasure of ID code Perform operation according to prompts on the Techstream screen 4 End of erasure Finish key ID code erasure HINT:
*: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure has not been finished within the specified time, perform the erasure from process 1 again. - ECU code registration:PROCEDURE CHART
Process Procedure 1 Start of registration - Connect the Techstream to DLC3
- Turn the engine switch on (IG)
HINT:
The engine switch cannot be turned on (IG) more than 10 times To continue the ECU code registration procedure with the engine switch off, after connecting the Techstream, turn the Techstream on while turning the driver side door courtesy light switch on and off repeatedly at intervals of 1 5 seconds
- Turn the Techstream on
- Enter the following menus Smart Access / Utility / ECU Communication ID Registration / ID code box (immobiliser code ECU) and Steering Lock
- Read "Seed Number" sent from TIS according to the Techstream screen
2 Confirmation of registered key* - Touch logo of registered key to engine switch
- Confirm that wireless door lock buzzer sounds once (short beep)
3 Erasure of ECU code Perform operation according to prompts on the Techstream screen 4 End of registration Finish ECU code registration HINT:
*: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure has not been finished within the specified time, perform the registration from process 1 again. - ECU communication ID registration:NOTE:
- The ECU communication ID should be registered when the ID code box (immobilizer code ECU), steering lock ECU or ECM is replaced in order to match the ECU communication ID.
- The engine cannot be started unless ECU communication ID is registered.
- After the registration, pressing the engine switch may not start the engine on the first try. If so, press the engine switch again.
- After the engine is started, clear DTC B2799 (code for ECM immobilizer communication error) using either of the following methods:
- Use the Techstream.
- Disconnect the cable from the negative (-) battery terminal for 30 seconds.
- Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
SST 09843-18040
- Turn the engine switch on (IG) (do not start the engine) and leave it as is for 30 minutes.
- Turn the engine switch off and disconnect terminals 13 (TC) and 4 (CG).
- Check that the engine starts and stays on for more than 3 seconds.
- ECU communication ID reregistration:NOTE: The ECU communication ID should be registered when the ECM is replaced in order to match the ECU communication ID.PROCEDURE CHART
Procedure Time Security Indicator Light Condition 1 Start - Off 2 While holding registered key, turn the engine switch on (IG) with brake pedal depressed 3 Check that engine starts and stays on for more than 3 seconds 4 End
- New key ID registration (when replacing certification ECU (smart key ECU assembly) and ID code box (immobilizer code ECU), or certification ECU (smart key ECU assembly), ID code box (immobilizer code ECU) and steering lock ECU):