LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> LS 600hL >> Repair and Diagnosis >> Engine Mechanical >> Auxiliary Emission Control Systems >> Emission Control >> PCV Valve >> Removal

PCV Valve: Removal

NOTE: While the negative battery terminal is connected, even if the power switch is OFF, the brake control system activates when the brake pedal is depressed or the door courtesy switch turns on. Therefore during servicing of the brake system components, do not operate the brake pedal or open/close the doors while the negative battery terminal is connected.
  1. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY  (See REMOVAL )
  2. REMOVE BATTERY SERVICE HOLE COVER LH  (See REMOVAL )
  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
    NOTE:
    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see INITIALIZATION ).
    • After the power switch is turned OFF, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the power switch OFF, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.
  4. REMOVE SERVICE PLUG GRIP  (See REMOVAL )
  5. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH  (See REMOVAL )
  6. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH  (See REMOVAL )
  7. REMOVE NO. 1 ENGINE UNDER COVER  (See REMOVAL )
  8. DRAIN ENGINE COOLANT  (See REPLACEMENT )
  9. REMOVE V-BANK COVER SUB-ASSEMBLY  (See REMOVAL )
  10. REMOVE AIR CLEANER INLET COVER SUB-ASSEMBLY  (See REMOVAL )
  11. REMOVE ENGINE ROOM SIDE COVER RH  (See REMOVAL )
  12. REMOVE ENGINE ROOM SIDE COVER LH  (See REMOVAL )
  13. REMOVE NO. 1 AIR CLEANER INLET  (See REMOVAL )
  14. REMOVE INTAKE AIR CONNECTOR PIPE  (See REMOVAL )
  15. REMOVE AIR CLEANER ASSEMBLY LH  (See REMOVAL )
  16. REMOVE AIR CLEANER ASSEMBLY RH  (See REMOVAL )
  17. DISCONNECT NO. 1 MOTOR COOLING PIPE  (See REMOVAL )
  18. REMOVE SKID CONTROL ECU  (See REMOVAL )
  19. DISCONNECT NO. 3 RELAY BLOCK  (See REMOVAL )
  20. DISCONNECT BRAKE FLUID RESERVOIR  (See REMOVAL )
  21. REMOVE SKID CONTROL ECU BRACKET  (See REMOVAL )
  22. REMOVE ENGINE COVER SUB-ASSEMBLY LH  (See REMOVAL )
  23. REMOVE NO. 6 COVER SUB-ASSEMBLY  (See REMOVAL )
  24. REMOVE ENGINE ROOM ECU COVER  (See REMOVAL )
  25. REMOVE OUTLET ENGINE ROOM ECM DUCT  (See REMOVAL )
  26. DISCONNECT HYBRID VEHICLE CONTROL ECU CONNECTOR  (See REMOVAL )
  27. REMOVE NO. 2 CONNECTOR HOLDER  (See REMOVAL )
  28. DISCONNECT ECM CONNECTOR  (See REMOVAL )
  29. REMOVE ENGINE WIRE HARNESS  (See REMOVAL )
  30. REMOVE INJECTOR DRIVER  (See REMOVAL )
  31. REMOVE FLEXIBLE HOSE BRACKET SUB-ASSEMBLY  (See REMOVAL )
  32. REMOVE ENGINE MOTOR CABLE CLAMP BRACKET  (See REMOVAL )
  33. REMOVE NO. 3 ENGINE COVER SUB-ASSEMBLY  (See REMOVAL )
  34. REMOVE THROTTLE BODY ASSEMBLY  (See REMOVAL )
  35. REMOVE WATER BY-PASS PIPE HOSE  (See REMOVAL )
  36. REMOVE PURGE VSV  (See REMOVAL )
  37. DISCONNECT PCV HOSE  (See REMOVAL )
  38. REMOVE INTAKE MANIFOLD  (See REMOVAL )
  39. REMOVE PCV VALVE 
    1. Disconnect the PCV hose.
    2. Remove the PCV valve.
      Fig 1: Locating PCV Valve
      G04943739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals