Rear Sunshade Assembly: Installation

INSTALL REAR SUNSHADE RELAY
NOTE: When reassembling the rear sunshade assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
1. Install the rear sunshade relay with the 2 screws.
2. Connect the connector.
  
  Fig 1: Locating Rear Sunshade Relay Screws And Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Engage the 4 claws and install the rear sunshade relay cover.
4. Install the screw.
  
  Fig 2: Identifying Rear Sunshade Relay Cover Claws And Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR WINDOW SHADE ASSEMBLY
1. Install the rear window shade assembly, and temporarily tighten 4 bolts < A > and < B >.
2. Fully tighten the 5 bolts.
3. Connect the connector.
  
  Fig 3: Identifying Rear Window Shade Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY
1. Engage the 5 claws and 3 clips, and install the No. 2 package tray trim panel assembly.
INSTALL HIGH MOUNTED STOP LIGHT SET (See INSTALLATION )
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
1. Thread the 3 rear seat belt floor anchors into the package tray trim panel assembly.
2. Insert the rear end of the package tray trim panel assembly into the rear window shade assembly.
3. Engage the 3 clips and install the package tray trim panel assembly.
  
  Fig 5: Identifying Package Tray Trim Panel Assembly Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Engage the 2 claws and install the rear seat shoulder belt cover.
  HINT:
  
  Use the same procedure for the other 2 rear seat shoulder belt covers.
  
  Fig 6: Identifying Rear Seat Shoulder Belt Covers Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Connect the floor side of the rear seat inner with center belt assembly RH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly RH and the protruding parts of the floor panel to overlap.
  
  Fig 7: Identifying Center Belt Assembly RH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when the belt is pulled out quickly.
7. Connect the floor side of the rear seat 3 point type belt assembly LH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat 3 point type belt assembly LH and the protruding parts of the floor panel to overlap.
  
  HINT:
  
  Use the same procedures for the RH side and the LH side.
  
  Fig 8: Identifying Rear Seat 3 Point Type Belt Assembly LH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when the belt is pulled out quickly.
INSTALL ROOF SIDE INNER GARNISH LH (See INSTALLATION )
INSTALL ROOF SIDE INNER GARNISH RH
INSTALL REAR SEAT SIDE GARNISH LH (See INSTALLATION )
INSTALL REAR SEAT SIDE GARNISH RH
INSTALL REAR DOOR SCUFF PLATE LH (See INSTALLATION )
INSTALL REAR DOOR SCUFF PLATE RH
INSTALL REAR SEATBACK ASSEMBLY (See INSTALLATION )
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
INSTALL REAR SEAT HEADREST ASSEMBLY
INSTALL REAR SEAT CUSHION ASSEMBLY (See INSTALLATION )