On-Vehicle Inspection

SMART ACCESS SYSTEM WITH PUSH-BUTTON START OPERATION INSPECTION

Check the entry unlock function.
1. Use the wireless lock operation to lock the doors. With the key in your possession, touch a door's outside handle (touch sensor) and check that the door unlocks.
Check the entry unlock operation's detection area.
1. Step 1: Hold the key at the same height as the door's outside handle (approximately 0.6 m (2.6 ft.)). Pay attention to the direction of the key in the illustration.
2. Step 2: Check that when the key is brought within 0.7 to 1.0 m (2.3 to 3.3 ft.) of the vehicle, the system enters unlock standby mode.
  HINT:
  
  Unlock standby mode is signified by the key's red LED illuminating.
  
  Fig 1: Identifying Key Distance From Vehicle
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Step 3: After the system enters unlock standby mode, touch the outside handle's sensor within 3 seconds. Check that the door unlocks.
  NOTE: The key cannot communicate with the system within a 0.2 m (0.6 ft.) radius of each outside handle.
4. Step 4: Repeat steps 2 and step 3 for the remaining doors.
5. Step 5: Inspect the door electrical key oscillator's response sensitivity. Wear protective gloves, set the system to unlock standby mode, and check that touching the inner side of the outside handle (the highlighted area in the illustration) with your finger causes the door to unlock.
  NOTE: When touching the highlighted area, tapping too quickly or having extended contact may not trigger the sensor. In such a case, the door will not unlock.
  
  Fig 2: Inspecting Door Electrical Key Oscillator Response Sensitivity
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Step 6: Repeat step 5 for the remaining doors.
Check the entry lock function.
1. Step 1: Close all of the vehicle's doors. With the key in your possession outside of the vehicle, check that pressing the lock switch locks the doors.
2. Step 2: Inspect the entry lock operation's detection area and the indoor electrical key antenna for wave leaks. Hold the key at a height of 1 m (3.3 ft.) (0.1 m (0.3 ft.) above the lower edge of the window frame). Pay attention to the direction and position of the key in the illustration. Check that when the key is approximately 0.3 m (0.9 ft.) from the vehicle and the lock switch is pressed, the front doors lock and the warning buzzer (for when the key is forgotten) does not sound. If the warning buzzer sounds, the indoor electrical key antenna may have a wave leak.
  
  Fig 3: Identifying Key Distance From Vehicle
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Due to the key being unable to communicate with the system within a 0.2 m (0.6 ft.) distance from the outside handle, do not press the lock switch with the same hand that is holding the key. The doors will not lock.
3. Step 3: Repeat step 1 and step 2 for the remaining doors.
Check the entry luggage compartment door open function.
1. Close the luggage compartment door. With the key in your possession, check that pressing the power luggage door open switch opens the luggage compartment door.
  
  Fig 4: Identifying Key Distance From Center Of Vehicle
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Inspect the entry luggage compartment door open operation's detection area. Hold the key at the same height as the power luggage door open switch (approximately 0.8 m (2.6 ft.)) and aligned with the center of the rear of the vehicle. Pay attention to the direction of the key shown in the illustration. Check that the when the key is brought within 0.7 to 1.0 m (2.3 to 3.3 ft.) of the vehicle, pressing the power luggage door open switch opens the luggage compartment door.
Check the entry ignition function.
1. When the hybrid system is off:
  With the key in your possession and the brake pedal depressed, check that pressing the power switch releases the steering wheel lock and starts the hybrid system.
  
  HINT:
  
  The hybrid system can be started only when the power switch indicator illuminates in green.
2. When the hybrid system is running:
  With the key in your possession, check that pressing the power switch stops the hybrid system and activates the steering wheel lock.
  
  HINT:
  
  The shift position must be P to be able to stop the hybrid system.
3. Inspect the entry ignition operation's detection area. Pay attention to the direction of the key in the illustration. When the key is in either of the 2 locations in the illustration, check that the hybrid system can start.
  
  Fig 5: Identifying Inspection Point
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE: The hybrid system cannot be started when the key is on the instrument panel or rear package tray, or in the glove box.
Check the key lock-in prevention function.
1. Place the key in the luggage compartment with all doors locked. Check that: 1) closing the luggage compartment door triggers the key's wireless buzzer (which lasts approximately 2 seconds), and 2) pressing the power luggage door open switch opens the luggage compartment door.
  
  Fig 6: Identifying Key Position
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Inspect the key lock-in prevention's detection area. Pay attention to the direction of the key shown in the illustration. When the key is in either of the 2 locations in the illustration, check that: 1) closing the luggage compartment door sounds the key's wireless buzzer, and 2) pressing the power luggage door open switch opens the luggage compartment door.
  NOTE: If the key in inside a metal storage item, such as a metal briefcase or metal box, the key will not be able to be detected by the system.
3. Inspect the key lock-in prevention's detection area and the entry door control receiver for wave leaks. Hold the key at the same height as the lower edge of the luggage compartment door and aligned with the center of the rear of the vehicle. Pay attention to the direction and position of the key shown in the illustration. Check that when the key is over 0.1 m (0.3 ft.) from the vehicle's rear bumper, the key's wireless buzzer does not sound.
  If the warning buzzer sounds, the entry door control receiver may have a wave leak.
  
  Fig 7: Identifying Key Position From Luggage End
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Check the key cancel function.
1. While the power switch is ON (IG), check that the power luggage door open switch is the only switch in the smart access system with push-button start that can be operated.
2. While the key cancel function (smart access system with push-button start cancel function) is ON, check that all functions in the smart access system with push-button start cannot be operated.

Check the answer-back function (hazard warning light flashing and buzzer sounding).

BUZZER SOUND REFERENCE

Entry Operation	Hazard Warning Light	Buzzer
Entry Door Lock	Flashes once	Sounds once
Entry Door Unlock	Flashes twice	Sounds twice
Entry Luggage Compartment Door Open	Does not flash	Does not sound

Check that the key reminder warning buzzer sounds.
1. Carry the key in the vehicle and close the driver side door. Then turn the power switch OFF or ON (ACC).
2. Open the driver side door and check that the buzzer sounds intermittently.
Check that the key reminder warning buzzer stops.
1. When the buzzer is sounding, check that the buzzer stops sounding if either of the following are performed:
  - Close the driver side door (front door courtesy light switch is off).
  - Turn the power switch ON (IG).