LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2007 >> RX 400h AWD >> Repair and Diagnosis >> Electrical >> Gauges >> Meter >> Meter / Gauge System >> Customize Parameters

Customize Parameters

  1. COMBINATION METER ASSEMBLY (Using Intelligent Tester) 

    HINT:

    The following item can be customized.

    NOTE:
    • Be sure to record the current value before customizing.
    • When performing troubleshooting, be aware that the functions may be set to OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function", check that the wireless operation is not set to OFF by customizing, then perform the troubleshooting.)

    METER: 

    METER REFERENCE CHART

    Display (Item) Default Contents Setting
    KEY REMND SOUND NORMAL Function to change cycle of key remind warning buzzer. 600 7 900/1,200 ms
    (1) U.S.A.

    (2) Except U.S.A.
  2. SEAT BELT BUZZER ON/OFF SETTING 
    Fig 1: Multi-Information Display - Seat Belt Buzzer ON/OFF Setting
    G05199682Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

    The buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.

    NOTE:
    • These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).
    • When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).
    • Odometer returns to 0 after starting this procedure, although it is not displayed.

    HINT:

    "SEAT BELT BUZZER OFF" indicates that the buzzer is OFF. "SEAT BELT BUZZER ON" indicates that the buzzer is ON. The buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/ TRIP switch is not operated for 10 seconds or more. In this case, perform step  11 to check that the buzzer ON/ OFF setting is complete. If it is not complete, start from step  1 again.

    1. Driver and front passenger side seat belt buzzers
      1. Turn the ignition switch to the ON position.
      2. Press the ODO/TRIP switch until the odometer displays "ODO".
      3. Ignition switch off.
      4. Turn the ignition switch to the ON position.
      5. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
      6. Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.
      7. Check that the odometer displays either "SEAT BELT BUZZER ON" or "SEAT BELT BUZZER OFF".
      8. Press the ODO/TRIP switch to change the display to "SEAT BELT BUZZER OFF".
      9. Ignition switch off.
      10. Turn the ignition switch to the ON position.
      11. Check that no buzzer sounds.
    2. Front passenger side seat belt buzzer
      1. Turn the ignition switch to the ON position.
      2. Press the ODO/TRIP switch until the odometer displays "ODO".
      3. Ignition switch off.
      4. Turn the ignition switch to the ON position.
      5. Sit in the front passenger seat. Press the ODO/ TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
      6. Sit in the front passenger seat. Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.
      7. Check that the odometer displays either "SEAT BELT BUZZER ON" or "SEAT BELT BUZZER OFF".
      8. Press the ODO/TRIP switch to change the display to "SEAT BELT BUZZER OFF".
      9. Ignition switch off.
      10. Turn the ignition switch to the ON position.
      11. Check that no buzzer sounds.
  3. TIME ZONE SETTING (w/ Navigation System) 
    Fig 2: Multi-Information Display - Time Zone Setting
    G05199683Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
scientia non olet · About LEMON Manuals