Charging (3UZ-FE): Generator: Reassembly

INSTALL GENERATOR ROTOR ASSEMBLY
1. Place the drive end frame on the pulley.
2. Install the rotor to the drive end frame.
Fig 1: Installing Rotor To Drive End Frame
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR COIL ASSEMBLY
1. Install the generator washer on the rotor.
  
  Fig 2: Placing Generator Washer On Generator Rotor
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a SST and press, slowly press in the coil.
  SST 09285-76010
  
  Fig 3: Pressing In Coil Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the coil with the 4 bolts.
  Torque: 5.8 N*m (59 kgf*cm, 51 in.*lbf)
Fig 4: Locating Bolts With Coil
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR PULLEY
1. Install the pulley to the rotor shaft with the pulley nut by hand.
2. Hold SST (A) with a torque wrench, and tighten SST (B) clockwise to the specified torque.
  SST 09820-63010
  
  Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf)
3. Check that SST (A) is secured to the pulley shaft.
  
  Fig 5: Installing Generator Pulley To Rotor Shaft
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Mount SST (C) in a vise.
5. Insert SST (B) into SST (C), and attach the pulley nut to SST (C).
  
  Fig 6: Inserting SST (B) Into SST (C)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. To tighten the pulley nut, turn SST (A) in the direction shown in the illustration.
  Torque: 133 N*m (1356 kgf*cm, 98 ft.*lbf)
7. Remove the generator from SST (C).
  
  Fig 7: Removing Generator From SST (C)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Turn SST (B) and remove SST (A and B).
  
  Fig 8: Turning SST (B)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR BRUSH HOLDER ASSEMBLY
1. While pushing the 2 brushes toward the inside of the brush holder, insert a pin ( 1.0 mm (0.039 in.)) into the brush holder hole.
  
  Fig 9: Inserting Pin Into Brush Holder Hole
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the generator brush holder with the 2 screws.
  Torque: 1.8 N*m (18 kgf*cm, 16 in.*lbf)
3. Pull out the pun from the generator brush holder.
  
  Fig 10: Locating Screws And Generator Brush Holder
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR REAR END COVER
1. Install the terminal insulator.
  NOTE: Pay attention the mounting orientation of the terminal insulator.
  
  Fig 11: Identifying Terminal Insulator
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the terminal insulator.
3. Install the end cover with the 3 nuts.
  Torque: 4.6 N*m (47 kgf*cm, 41 in.*lbf)
CHECK THAT ROTOR ROTATES SMOOTHLY

Fig 12: Locating Nuts And Terminal Insulator
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002