LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2006 >> RX 330 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 2 (Supplemental Restraint System - Diagnostics) >> DTC B1785 Occupant Classification Sensor Front LH Collision Detection Malfunction >> Inspection Procedure

Inspection Procedure

WARNING: This page is about a different car, the 2006 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
  1. PERFORM ZERO POINT CALIBRATION 
    1. Connect the hand-held tester to the DLC3.
    2. Turn the ignition switch to the ON position.
    3. Using the hand-held tester, perform "Zero point calibration" (see INITIALIZATION  ).

      OK: The "COMPLETED" is displayed. 

    NG: Go to step   4 

    OK: GO TO NEXT STEP 

  2. PERFORM SENSITIVITY CHECK 
    1. Using the hand-held tester, perform "Sensitivity check" (see INITIALIZATION  ).

      Standard value: 27 to 33 kg (59.52 to 72.75 lb) 

    NG: Go to step   4 

    OK: GO TO NEXT STEP 

  3. CHECK DTC 
    1. Turn the ignition switch to the ON position.
    2. Clear the DTCs stored in memory (see DTC CHECK/CLEAR  ).

      HINT:

      First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assy center.

    3. Turn the ignition switch to the LOCK position.
    4. Turn the ignition switch to the ON position.
    5. Using the hand-held tester, check the DTCs (see DTC CHECK/CLEAR  ).

      OK: DTC B1785 is not output. 

      HINT:

      Codes other than code B1785 may be output at this time, but they are not related to this check.

    NG: Go to step   4 

    OK: END 

  4. REPLACE FRONT RH SEAT ASSY 
    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Replace the front RH seat assy (see OVERHAUL (Manual Seat Type) , OVERHAUL (Power Seat Type)).

      HINT:

      Perform the inspection using parts from a normal vehicle if possible.

  5. PERFORM ZERO POINT CALIBRATION 
    1. Connect the hand-held tester to the DLC3.
    2. Connect the negative (-) terminal cable to the battery.
    3. Turn the ignition switch to the ON position.
    4. Using the hand-held tester, perform "Zero point calibration" (see INITIALIZATION  ).

      OK: The "COMPLETED" is displayed. 

    NG: Go to step   8 

    OK: GO TO NEXT STEP 

  6. PERFORM SENSITIVITY CHECK 
    1. Using the hand-held tester, perform "Sensitivity check" (see INITIALIZATION  ).

      Standard value: 27 to 33 kg (59.52 to 72.75 lb) 

    NG: Go to step   8 

    OK: GO TO NEXT STEP 

  7. CHECK DTC 
    1. Turn the ignition switch to the ON position.
    2. Clear the DTCs stored in memory (see DTC CHECK/CLEAR  ).

      HINT:

      First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assy center.

    3. Turn the ignition switch to the LOCK position.
    4. Turn the ignition switch to the ON position.
    5. Using the hand-held tester, check the DTCs (see DTC CHECK/CLEAR  ).

      OK: DTC B1785 is not output. 

      HINT:

      Codes other than code B1785 may be output at this time, but they are not related to this check.

    NG: Go to step   8 

    OK: END 

  8. REPLACE OCCUPANT CLASSIFICATION ECU 
    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Replace the occupant classification ECU (see REPLACEMENT ).
  9. PERFORM ZERO POINT CALIBRATION 
    1. Connect the hand-held tester to the DLC3.
    2. Connect the negative (-) terminal cable to the battery.
    3. Turn the ignition switch to the ON position.
    4. Using the hand-held tester, perform "Zero point calibration" (see INITIALIZATION  ).

      OK: The "COMPLETED" is displayed. 

  10. PERFORM SENSITIVITY CHECK 
    1. Using the hand-held tester, perform "Sensitivity check" (see INITIALIZATION  ).

      Standard value: 27 to 33 kg (59.52 to 72.75 lb) 

scientia non olet · About LEMON Manuals