Data List / Active Test

HINT:

According to the DATA LIST displayed on the intelligent tester, the value and status of the switch, sensor, actuator, etc. can be obtained without part removal. Reading the DATA LIST as the first step in troubleshooting is one way to shorten labor time.

1. Connect the intelligent tester to the DLC3.
2. Turn the engine switch on (IG).
3. From the display on the tester, read the "DATA LIST".
   DATA LIST
   
   

   Item	Measurement Item/Range (Display)	Normal Condition	Diagnostic Note
   VEHICLE SPD	Vehicle speed reading/ min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed	Speed indicated on speedometer
   IG VOLTAGE	ECU power supply voltage/ min.: 0 V, max.: 25.5 V	Actual ECU power supply voltage: 10 to 14 V	-
   STEERING ANGLE	Steering angle sensor reading/min.: -73725.75 deg, max.: 73728 deg	Actual steering angle Left turn: Reading increases Right turn: Reading decreases	Zero point is set when the battery is connected
   ENGINE SPD	Cam position sensor reading/min.: 0 rpm, max.: 25,500 rpm	Actual engine speed	Speed indicated on the combination meter
   STOP LIGHT SW	Stop light switch/ ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
   DAMPER SW 1	Damping force switch 1/ ON or OFF	The same as absorber control switch position	Operate the absorber control switch
   TS	TS terminal/ON or OFF	ON: During test mode OFF: Normal mode	-
   TC	TC terminal/ ON or OFF	ON: DTC recorded OFF: No DTC recorded	-
   G (UP & DOWN) FR	G (up & down) FR sensor reading/ min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2	-8,820 mm/s2 to 980 mm/s2 at still condition	Reading changes when vehicle (FR) is bounced
   G (UP & DOWN) FL	G (up & down) FL sensor reading/min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2	-8,820 mm/s2 to 980 mm/s2 at still condition	Reading changes when vehicle (FL) is bounced
   G (UP & DOWN) R	G (up & down) rear sensor reading/ min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2	-8,820 mm/s2 to 980 mm/s2 at still condition	Reading changes when vehicle (rear) is bounced
   DAMPER FR	Damper step FR/ min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   DAMPER FL	Damper step FL/ min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   DAMPER RR	Damper step RR/ min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   DAMPER RL	Damper step RL/ min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   WHEEL SPD FR	Front right wheel speed reading/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed	Speed indicated on speedometer
   MAX DMP STEP FR	Max. damper step FR/ min.: 0 step, max.: 255 step	17 step at still condition	-
   MAX DMP STEP FL	Max. damper step FL/ min.: 0 step, max.: 255 step	17 step at still condition	-
   MAX DMP STEP RR	Max. damper step RR/ min.: 0 step, max.: 255 step	17 step at still condition	-
   MAX DMP STEP RL	Max. damper step RL/ min.: 0 step, max.: 255 step	17 step at still condition	-
   #CODES	Number of DTC recorded/ min.: 0, max.: 255	Min.: 0, Max.: XX	-

HINT:

Performing the ACTIVE TEST using the intelligent tester allows the relay, actuator, etc. to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

1. Connect the intelligent tester to DLC3.
2. Turn the engine switch on (IG).
3. According to the display on the tester, perform the "ACTIVE TEST".
   ACTIVE TEST
   
   

   Check Item	Vehicle Condition/Test details	Diagnostic Note
   DAMPER FR	Damper step front right wheel	1 step to 17 steps (Damper step is change)
   DAMPER FL	Damper step front left wheel	1 step to 17 steps (Damper step is change)
   DAMPER RR	Damper step rear right wheel	1 step to 17 steps (Damper step is change)
   DAMPER RL	Damper step rear left wheel	1 step to 17 steps (Damper step is change)