Diagnostic Trouble Code Index DTC: Transfer Case Control Module (TCCM) -- Range Rover/L405
- General Information
- Description And Operation
- Diagnostic Trouble Code Index - DTC: Transfer Case Control Module (TCCM) (G2016291)
- Transfer Case Control Module (TCCM)
- DTC P0605-41: Internal Control Module Read Only Memory (ROM) Error - General checksum failure
- DTC P0605-43: Internal Control Module Read Only Memory (ROM) Error - Special memory failure
- DTC P062F-43: Internal Control Module EEPROM Error - Special memory failure
- DTC P062F-68: Internal Control Module EEPROM Error - Event information
- DTC P0666-11: Control Module Internal Temperature Sensor "A" Circuit - Circuit short to ground
- DTC P0666-12: Control Module Internal Temperature Sensor "A" Circuit - Circuit short to battery
- DTC P0666-29: Control Module Internal Temperature Sensor "A" Circuit - Signal invalid
- DTC P0666-64: Control Module Internal Temperature Sensor "A" Circuit - Signal plausibility failure
- DTC P080A-56: Clutch Position Not Learned - Invalid/incomplete configuration
- DTC P0810-04: Clutch Position Control Error - System internal failures
- DTC P0810-07: Clutch Position Control Error - Mechanical failures
- DTC P0810-28: Clutch Position Control Error - Signal bias level out of range/zero adjustment failure
- DTC P0810-46: Clutch Position Control Error - Calibration/parameter memory failure
- DTC P0810-56: Clutch Position Control Error - Invalid/incomplete configuration
- DTC P0810-62: Clutch Position Control Error - Signal compare failure
- DTC P0810-77: Clutch Position Control Error - Commanded position not reachable
- DTC P0810-78: Clutch Position Control Error - Alignment or adjustment incorrect
- DTC P0919-94: Gear Shift Position Control Error - Unexpected operation
- DTC P160C-45: Control Module Software Performance - Program memory failure
- DTC P160C-48: Control Module Software Performance - Supervision software failure
- DTC P160C-94: Control Module Software Performance - Unexpected operation
- DTC P170E-07: Clutch Delivered Torque Performance - Mechanical failures
- DTC P170E-92: Clutch Delivered Torque Performance - Performance or incorrect operation
- DTC P175B-00: Transfer Case Clutch Deteriorated - No sub type information
- DTC P183A-67: Range Change Mechanism Failure - Signal incorrect after event
- DTC P183A-77: Range Change Mechanism Failure - Commanded position not reachable
- DTC P186D-71: Clutch Actuator Stuck - Actuator stuck
- DTC P18A4-13: Motion/Position Sensor Power Circuit - Circuit open
- DTC P18A4-16: Motion/Position Sensor Power Circuit - Circuit voltage below threshold
- DTC P18A4-17: Motion/Position Sensor Power Circuit - Circuit voltage above threshold
- DTC P18A5-03: Motion/Position Sensor A Signal Circuit - FM (Frequency Modulated)/PWM (Pulse Width Modulated) failures
- DTC P18A5-11: Motion/Position Sensor A Signal Circuit - Circuit short to ground
- DTC P18A5-12: Motion/Position Sensor A Signal Circuit - Circuit short to battery
- DTC P18A5-13: Motion/Position Sensor A Signal Circuit - Circuit open
- DTC P18A5-37: Motion/Position Sensor A Signal Circuit - Signal frequency too high
- DTC P18A5-62: Motion/Position Sensor A Signal Circuit - Signal compare failure
- DTC P215A-62: Vehicle Speed/Wheel Speed Correlation - Signal compare failure
- DTC P215A-64: Vehicle Speed/Wheel Speed Correlation - Signal plausibility failure
- DTC P2787-98: Clutch Temperature Too High - Component or system over temperature
- DTC U0080-81: Vehicle Communication Bus F - Invalid serial data received
- DTC U0080-82: Vehicle Communication Bus F - Alive/sequence counter incorrect/not updated
- DTC U0080-83: Vehicle Communication Bus F - Value of signal protection calculation incorrect
- DTC U0080-87: Vehicle Communication Bus F - Missing message
- DTC U0080-88: Vehicle Communication Bus F - Bus off
- DTC U1000-02: Solid State Driver Protection Active - Driver Disabled - General signal failure
- DTC U1000-11: Solid State Driver Protection Active - Driver Disabled - Circuit short to ground
- DTC U1000-12: Solid State Driver Protection Active - Driver Disabled - Circuit short to battery
- DTC U1000-16: Solid State Driver Protection Active - Driver Disabled - Circuit voltage below threshold
- DTC U1000-17: Solid State Driver Protection Active - Driver Disabled - Circuit voltage above threshold
- DTC U1000-1C: Solid State Driver Protection Active - Driver Disabled - Circuit voltage out of range
- DTC U1000-49: Solid State Driver Protection Active - Driver Disabled - Internal electronic failure
- DTC U1000-4B: Solid State Driver Protection Active - Driver Disabled - Over temperature
- DTC U1000-56: Solid State Driver Protection Active - Driver Disabled - Invalid/incomplete configuration
- DTC U1000-62: Solid State Driver Protection Active - Driver Disabled - Signal compare failure
- DTC U1A4B-04: Control Module Processor B - System internal failures
- DTC U1A4B-16: Control Module Processor B - Circuit voltage below threshold
- DTC U1A4B-17: Control Module Processor B - Circuit voltage above threshold
- DTC U1A4B-1C: Control Module Processor B - Circuit voltage out of range
- DTC U1A4B-47: Control Module Processor B - Watchdog/safety microcontroller failure
- DTC U1A4B-48: Control Module Processor B - Supervision software failure
- DTC U1A4B-49: Control Module Processor B - Internal electronic failure
- DTC U1A4B-4B: Control Module Processor B - Over temperature
- DTC U1A4B-55: Control Module Processor B - Not configured
- DTC U1A4B-56: Control Module Processor B - Invalid/incomplete configuration
- DTC U1A4B-64: Control Module Processor B - Signal plausibility failure
- DTC U1A4B-84: Control Module Processor B - Signal below allowable range
- DTC U1A4B-92: Control Module Processor B - Performance or incorrect operation
- DTC U1A4B-9A: Control Module Processor B - Component or system operating conditions
- DTC U200C-4B: Control Module Internal Power C - Over temperature
- DTC U200C-64: Control Module Internal Power C - Signal plausibility failure
- DTC U200C-9A: Control Module Internal Power C - Component or system operating conditions
- DTC U2011-16: Motor - Circuit voltage below threshold
- DTC U2011-17: Motor - Circuit voltage above threshold
- DTC U2011-18: Motor - Circuit current below threshold
- DTC U2011-19: Motor - Circuit current above threshold
- DTC U2011-1D: Motor - Circuit current out of range
- DTC U2011-28: Motor - Signal bias level out of range/zero adjustment failure
- DTC U2011-41: Motor - General checksum failure
- DTC U2011-4B: Motor - Over temperature
- DTC U2011-56: Motor - Invalid/incomplete configuration
- DTC U2011-62: Motor - Signal compare failure
- DTC U2011-68: Motor - Event information
- DTC U2011-77: Motor - Commanded position not reachable
- DTC U2011-78: Motor - Alignment or adjustment incorrect
- DTC U2011-85: Motor - Signal above allowable range
- DTC U2011-86: Motor - Signal invalid
- DTC U2011-98: Motor - Component or system over temperature
- DTC U2011-9A: Motor - Component or system operating conditions
- DTC U2016-04: Control Module Main Software - System internal failures
- DTC U2016-06: Control Module Main Software - Algorithm based failures
- DTC U2016-47: Control Module Main Software - Watchdog/safety microcontroller failure
- DTC U2016-49: Control Module Main Software - Internal electronic failure
- DTC U2016-92: Control Module Main Software - Performance or incorrect operation
- DTC U201A-54: Control Module Main Calibration Data - Missing calibration
- DTC U2100-54: Initial Configuration Not Complete - Missing calibration
- DTC U2101-56: Control Module Configuration Incompatible - Invalid/incomplete configuration
- DTC U2300-54: Central Configuration - Missing calibration
- DTC U2300-55: Central Configuration - Not configured
- DTC U2300-56: Central Configuration - Invalid/incomplete configuration
- DTC U2300-64: Central Configuration - Signal plausibility failure
- DTC U3000-1C: Control Module - Circuit voltage out of range
- DTC U3000-42: Control Module - General memory failure
- DTC U3000-4A: Control Module - Incorrect component installed
- DTC U3000-4B: Control Module - Over temperature
- DTC U3000-92: Control Module - Performance or incorrect operation
- DTC U3000-94: Control Module - Unexpected operation
- DTC U3000-98: Control Module - Component or system over temperature
- DTC U3006-13: Control Module Input Power "A" - Circuit open
- DTC U3006-16: Control Module Input Power "A" - Circuit voltage below threshold
- DTC U3006-17: Control Module Input Power "A" - Circuit voltage above threshold
- DTC U3006-85: Control Module Input Power "A" - Signal above allowable range
- DTC U3012-04: Control Module Improper Wake-up Performance - System internal failures
- DTC U3012-1C: Control Module Improper Wake-up Performance - Circuit voltage out of range
- DTC U3012-41: Control Module Improper Wake-up Performance - General checksum failure
- DTC U3012-48: Control Module Improper Wake-up Performance - Supervision software failure
- DTC U3012-92: Control Module Improper Wake-up Performance - Performance or incorrect operation
- DTC U3012-94: Control Module Improper Wake-up Performance - Unexpected operation
- DTC U3012-96: Control Module Improper Wake-up Performance - Component internal failure
- Diagnostic Trouble Code Index - DTC: Transfer Case Control Module (TCCM) (G2016291)
- Description And Operation