LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2018 >> Range Rover Velar Base >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Diagnostic Trouble Code Index DTC: Transmission Control Module (TCM) -- Range Rover Velar/L560 >> General Information >> Description And Operation >> Diagnostic Trouble Code Index - DTC: Transmission Control Module (TCM) (G2720603) >> Transmission Control Module (TCM)

Transmission Control Module (TCM)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT  acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTE:
  • Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
  • If a control module or a component is at fault and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component.
  • Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).
  • When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
  • Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
  • Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
  • If Diagnostic Trouble Code(s) are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
  • Check JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and complete the recommendations as required.
  • If a failure condition is reported indicating the need to renew the transmission assembly on a vehicle that remains under manufacturer warranty, an authorization request must first go through the warranty prior approval program before any work is begun.

The table below lists all Diagnostic Trouble Codes (Diagnostic Trouble Code(s)) that could be set in the Transmission Control Module (TCM). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing article in the repair information. For additional information, refer to the appropriate repair information.

DTC DESCRIPTION POSSIBLE CAUSES ACTION
P0218-98 Transmission Fluid Temperature Sensor "A" Over Temperature Condition - Component or system over temperature
  • Restricted airflow to the automatic transmission cooler
  • Poor automatic transmission fluid quality
  • Check for debris blocking the air flow to the automatic transmission cooler. Clear debris as necessary, clear the DTC and retest
  • Perform sufficient road test for the vehicle to reach normal operating temperature. Check the quality of the automatic transmission fluid. Replace the automatic transmission fluid as necessary. Clear the DTC and retest
  • If the fault persists and the gear shift quality remains poor, or if the DTC re-occurs, contact the technical help desk for further assistance
P0219-86 Engine Overspeed Condition - Signal invalid
  • Missing/invalid data from the powertrain control module
  • Wheel/tire size incorrect
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle
P0501-64 Vehicle Speed Sensor A Circuit Range/Performance - Signal plausibility failure
  • Driveshaft(s) not correctly installed
  • Damage to driveline components
  • Missing/invalid data from the anti-lock brake system control module
  • Inspect the driveshafts for correct installation. If driveshafts are not correctly installed, check for any damage to the driveshafts. Refit or replace the driveshafts as required
  • Visually inspect all other driveline components and check for damage. Replace any damaged components as required
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, raise a Technical Assist (TA) for further support
P0501-86 Vehicle Speed Sensor A Circuit Range/Performance - Signal invalid
  • Driveshaft(s) not correctly installed
  • Damage to driveline components
  • Missing/invalid data from the anti-lock brake system control module
  • Inspect the driveshafts for correct installation. If driveshafts are not correctly installed, check for any damage to the driveshafts. Refit or replace the driveshafts as required
  • Visually inspect all other driveline components and check for damage. Replace any damaged components as required
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, raise a Technical Assist (TA) for further support
P0561-62 System Voltage Unstable - Signal compare failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0562-1C System Voltage Low - Circuit voltage out of range
  • Transmission control module power or ground circuit open circuit, high resistance
  • Battery/charging system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - Main ECU Supply Voltage (0xDD02). Refer to the appropriate system wiring diagrams and check the transmission control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the relevant article of the repair information and check the battery and charging system. Rectify as necessary
P0562-21 System Voltage Low - Signal amplitude < minimum
  • Transmission control module power or ground circuit open circuit, high resistance
  • Battery/charging system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - Main ECU Supply Voltage (0xDD02). Refer to the appropriate system wiring diagrams and check the transmission control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the relevant article of the repair information and check the battery and charging system. Rectify as necessary
P0563-22 System Voltage High - Signal amplitude > maximum
  • Battery/charging system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - Main ECU Supply Voltage (0xDD02). Refer to the relevant article of the repair information and check the battery and charging system. Rectify as necessary
P0600-04 Serial Communication Link - System internal failures
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0601-41 Internal Control Module Memory Checksum Error - General checksum failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0605-41 Internal Control Module Read Only Memory (ROM) Error - General checksum failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0606-04 Control Module Processor - System internal failures
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0606-16 Control Module Processor - Circuit voltage below threshold
  • Transmission control module power or ground circuit open circuit, high resistance
  • Battery/charging system fault
  • Refer to the appropriate system wiring diagrams and check the transmission control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the relevant article of the repair information and check the battery and charging system. Rectify as necessary
P0606-62 Control Module Processor - Signal compare failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0606-64 Control Module Processor - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P060B-04 Internal Control Module A/D Processing Performance - System internal failures
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0613-47 TCM Processor - Watchdog/safety microcontroller failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0613-62 TCM Processor - Signal compare failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0613-98 TCM Processor - Component or system over temperature
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P062C-29 Internal Control Module Vehicle Speed Performance - Signal invalid
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, contact Retailer Technical Support
P062C-86 Internal Control Module Vehicle Speed Performance - Signal invalid
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P062F-04 Internal Control Module EEPROM Error - System internal failures
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0657-13 Actuator Supply Voltage A Circuit/Open - Circuit open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P06A6-16 Sensor Reference Voltage A Circuit Range/Performance - Circuit voltage below threshold
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P06A6-17 Sensor Reference Voltage A Circuit Range/Performance - Circuit voltage above threshold
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0700-02 Transmission Control System (MIL Request) - General signal failure
  • Transmission system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check for other Diagnostic Trouble Code(s) and perform the relevant corrective actions. Clear the Diagnostic Trouble Code(s) and retest
P0702-04 Transmission Control System Electrical - System internal failures
  • Transmission control module power or ground circuit open circuit, high resistance
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (0xD112). Check the integrity of the transmission control module electrical connector. Check for correct latching, backed out terminals and corrosion. Refer to the appropriate system wiring diagrams and check the transmission control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
P0702-06 Transmission Control System Electrical - Algorithm based failures
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0702-98 Transmission Control System Electrical - Component or system over temperature
  • Transmission cooling system fault
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Check the automatic transmission cooling system
P0711-64 Transmission Fluid Temperature Sensor A Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0715-12 Input/Turbine Shaft Speed Sensor A Circuit - Circuit short to battery
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0715-22 Input/Turbine Shaft Speed Sensor A Circuit - Signal amplitude > maximum
  • Turbine sensor signal implausible
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. Check datalogger signals - Turbine Speed (0x1E72) - Transmission Output Shaft Speed (0x1E68) - for plausibility. If the fault persists, install a new transmission control module
P0715-64 Input/Turbine Shaft Speed Sensor A Circuit - Signal plausibility failure
  • Input shaft speed sensor signal implausible
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. Check datalogger signals - Turbine Speed (0x1E72) - Transmission Output Shaft Speed (0x1E68) - for plausibility. If the fault persists, install a new transmission control module
P0716-14 Input/Turbine Shaft Speed Sensor A Circuit Range/Performance - Circuit short to ground or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0720-12 Output Shaft Speed Sensor Circuit - Circuit short to battery
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0721-02 Output Shaft Speed Sensor Circuit Range/Performance - General signal failure
  • Output shaft speed sensor signal implausible
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. Check datalogger signals - Turbine Speed (0x1E72) - Transmission Output Shaft Speed (0x1E68) - for plausibility. If the fault persists, install a new transmission control module
P0721-22 Output Shaft Speed Sensor Circuit Range/Performance - Signal amplitude > maximum
  • Output shaft speed sensor signal implausible
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0721-27 Output Shaft Speed Sensor Circuit Range/Performance - Signal rate of change above threshold
  • Output shaft speed sensor signal implausible
NOTE: This DTC may be induced by an anti-lock braking system fault that allows the brakes to lock during braking.
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index. Clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new automatic transmission
P0721-64 Output Shaft Speed Sensor Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0722-14 Output Shaft Speed Sensor Circuit No Signal - Circuit short to ground or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0725-81 Engine Speed Input Circuit - Invalid serial data received
  • Missing/invalid data from the powertrain control module
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0726-21 Engine Speed Input Circuit Range/Performance - Signal amplitude < minimum
  • Missing/invalid data from the powertrain control module
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0729-07 Gear 6 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0730-00 Incorrect Gear Ratio - No sub type information
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0731-07 Gear 1 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0732-07 Gear 2 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0733-07 Gear 3 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0734-07 Gear 4 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0735-07 Gear 5 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0736-07 Reverse Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0736-22 Reverse Incorrect Ratio - Signal amplitude > maximum
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P0741-07 Torque Converter Clutch Circuit Performance/Stuck Off - Mechanical failures
  • Torque converter lock up clutch mechanical failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. If the fluid condition is normal, install a new torque converter. If the fluid is dirty or degraded, install a new automatic transmission
P0745-11 Pressure Control Solenoid A - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0745-15 Pressure Control Solenoid A - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0748-11 Pressure Control Solenoid A Electrical - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0748-15 Pressure Control Solenoid A Electrical - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P076F-07 Gear 7 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P077B-92 Output Shaft Speed Sensor Circuit - Direction Error - Performance or incorrect operation
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0780-62 Shift Error - Signal compare failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0780-93 Shift Error - No operation
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P07B3-11 Transmission Park Position Sensor/Switch A Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P07B4-15 Transmission Park Position Sensor/Switch A Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P07B9-11 Transmission Park Position Sensor/Switch B Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P07BA-15 Transmission Park Position Sensor/Switch B Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P07D9-07 Gear 8 Incorrect Ratio - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07DC-07 Incorrect Shift from Gear 1 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07DD-07 Incorrect Shift from Gear 2 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07DE-07 Incorrect Shift from Gear 3 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07DF-07 Incorrect Shift from Gear 4 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07E0-07 Incorrect Shift from Gear 5 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07E1-07 Incorrect Shift from Gear 6 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07E2-07 Incorrect Shift from Gear 7 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07E3-07 Incorrect Shift from Gear 8 - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P07E7-07 Stuck in Drive - Mechanical failures
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0801-94 Reverse Inhibit Control Circuit/Open - Unexpected operation
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0810-64 Clutch Position Control Error - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P084F-29 Park/Neutral Switch Output Circuit - Signal invalid
NOTE: Circuit reference - P-SIGNAL -
  • Park/neutral output signal circuit short circuit to ground, short circuit to power
  • Transmission control module internal failure
  • Refer to the appropriate system wiring diagrams and check the park/neutral output signal circuit for short circuit to ground, short circuit to power. Repair the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0850-29 Park/Neutral Switch Input Circuit - Signal invalid
  • Emergency park release deployed
  • Parklock mechanism failure
  • Transmission control module internal failure
  • Check the integrity of the emergency park release. Rectify as necessary
  • Check the integrity of the parklock mechanism. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. Check the parklock mechanism by engaging and disengaging the parklock several times. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0893-07 Multiple Gears Engaged - Mechanical failures
  • Automatic transmission internal failure
  • Install a new automatic transmission
P0950-08 Auto Shift Manual Control Circuit - Bus signal/message failures
  • Missing/invalid data from the body control module - Paddle switch signal
  • Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0950-24 Auto Shift Manual Control Circuit - Signal stuck high
  • Paddle switch stuck active
  • Check the operation of the paddle switches. Free the stuck switch or install a new paddle switch as necessary
P0950-29 Auto Shift Manual Control Circuit - Signal invalid
  • Transmission control switch fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0950-64 Auto Shift Manual Control Circuit - Signal plausibility failure
  • Transmission control switch fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0955-29 Auto Shift Manual Mode Circuit - Signal invalid
  • Transmission control switch fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P0966-11 Pressure Control Solenoid B Control Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0966-15 Pressure Control Solenoid B Control Circuit Low - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0966-64 Pressure Control Solenoid B Control Circuit Low - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0972-64 Shift Solenoid A Control Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0973-11 Shift Solenoid A Control Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0974-15 Shift Solenoid A Control Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0975-64 Shift Solenoid B Control Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0976-11 Shift Solenoid B Control Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0977-15 Shift Solenoid B Control Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0978-64 Shift Solenoid C Control Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0979-11 Shift Solenoid C Control Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0980-15 Shift Solenoid C Control Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0981-64 Shift Solenoid D Control Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0982-11 Shift Solenoid D Control Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0983-15 Shift Solenoid D Control Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0984-64 Shift Solenoid E Control Circuit Range/Performance - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0985-11 Shift Solenoid E Control Circuit Low - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P0986-15 Shift Solenoid E Control Circuit High - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P1608-16 Watchdog Malfunction - Circuit voltage below threshold
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P164C-62 Internal Control Module Start-Stop Performance - Signal compare failure
NOTE: This DTC is only active with vehicles installed with stop/start functionality
  • Engine system fault (auto stop/start system)
  • Using the Jaguar Land Rover approved diagnostic equipment, perform an ECO-start and monitor the engine speed and engine/transmission start/stop and position signals
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P1706-94 High Vehicle Speed Observed in Park - Unexpected operation
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P1707-72 Transfer Case Neutral or Park/Neutral Indication Circuit - Actuator stuck open
  • Emergency park release deployed
  • Parklock mechanism failure
  • Transmission control module internal failure
  • Check the integrity of the emergency park release. Rectify as necessary
  • Check the integrity of the parklock mechanism. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. Check the parklock mechanism by engaging and disengaging the parklock several times. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P1707-74 Transfer Case Neutral or Park/Neutral Indication Circuit - Actuator slipping
  • Emergency park release deployed
  • Parklock mechanism failure
  • Transmission control module internal failure
  • Check the integrity of the emergency park release. Rectify as necessary
  • Check the integrity of the parklock mechanism. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. Check the parklock mechanism by engaging and disengaging the parklock several times. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P1707-77 Transfer Case Neutral or Park/Neutral Indication Circuit - Commanded position not reachable
  • Emergency park release deployed
  • Parklock mechanism failure
  • Transmission control module internal failure
  • Check the integrity of the emergency park release. Rectify as necessary
  • Check the integrity of the parklock mechanism. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. Check the parklock mechanism by engaging and disengaging the parklock several times. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P1707-94 Transfer Case Neutral or Park/Neutral Indication Circuit - Unexpected operation
  • Emergency park release deployed
  • Parklock mechanism failure
  • Transmission control module internal failure
  • Check the integrity of the emergency park release. Rectify as necessary
  • Check the integrity of the parklock mechanism. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. Check the parklock mechanism by engaging and disengaging the parklock several times. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P170F-64 Clutch Pressure Release Valve Failed - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P174E-62 Output Shaft Speed/ABS Wheel Speed Correlation - Signal compare failure
  • Driveshaft(s) not correctly installed
  • Damage to driveline components
  • Anti-lock brake system fault
  • Transmission control module internal failure - Output shaft speed sensor circuit fault
  • Inspect the driveshafts for correct installation. If driveshafts are not correctly installed, check for any damage to the driveshafts. Refit or replace the driveshafts as required
  • Visually inspect all other driveline components and check for damage. Replace any damaged components as required
  • Using the Jaguar Land Rover approved diagnostic equipment, check vehicle speed and automatic transmission speed sensor signals
  • If the automatic transmission speed sensor signals are inaccurate, using the Jaguar Land Rover approved diagnostic equipment, check the automatic transmission wiring and rectify as required. Check for related Diagnostic Trouble Code(s) in the transmission control module and refer to the relevant DTC index
  • If the vehicle speed signals are inaccurate, using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, raise a Technical Assist (TA) for further support
P1758-19 Pressure Solenoid Control System Incorrect Current - Circuit current above threshold
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P1770-04 Clutch Solenoid Circuit - System internal failures
  • Automatic transmission internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. Check that the gear selection display on the instrument cluster matches the engaged gear. If the fault persists, install a new automatic transmission
P177A-07 Transmission Friction Element A or B - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P177B-07 Transmission Friction Element A or C - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P177C-07 Transmission Friction Element A or D - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P177D-07 Transmission Friction Element A or E - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P177E-07 Transmission Friction Element B or C - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P177F-07 Transmission Friction Element B or D - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P178A-07 Transmission Friction Element B or E - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P178B-07 Transmission Friction Element C or D - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P178C-07 Transmission Friction Element C or E - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P178D-07 Transmission Friction Element D or E - Mechanical failures
  • Automatic transmission internal failure
  • Refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and road test the vehicle. If the fault persists, install a new automatic transmission
P1935-86 Brake Switch/Sensor Signal - Signal invalid
  • Brake pedal switch signal implausible
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P2544-86 Torque Management Request Input Signal A - Signal invalid
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2545-86 Torque Management Request Input Signal A Range/Performance - Signal invalid
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2546-86 Torque Management Request Input Signal A Low - Signal invalid
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2547-86 Torque Management Request Input Signal A High - Signal invalid
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2638-67 Torque Management Feedback Signal A Range/Performance - Signal incorrect after event
  • Engine system fault
NOTE: DO NOT  replace the Automatic Transmission or the Mechatronics for this DTC
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P2700-07 Transmission Friction Element A Apply Time Range/Performance - Mechanical failures
  • Automatic transmission internal failure
  • Install a new automatic transmission
P2701-07 Transmission Friction Element B Apply Time Range/Performance - Mechanical failures
  • Automatic transmission internal failure
  • Install a new automatic transmission
P2702-07 Transmission Friction Element C Apply Time Range/Performance - Mechanical failures
  • Automatic transmission internal failure
  • Install a new automatic transmission
P2703-07 Transmission Friction Element D Apply Time Range/Performance - Mechanical failures
  • Automatic transmission internal failure
  • Install a new automatic transmission
P2704-07 Transmission Friction Element E Apply Time Range/Performance - Mechanical failures
  • Automatic transmission internal failure
  • Install a new automatic transmission
P2711-94 Unexpected Mechanical Gear Disengagement - Unexpected operation
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P272C-11 Park Pawl Motor Control Circuit - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P272C-15 Park Pawl Motor Control Circuit - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2759-11 Torque Converter Clutch Pressure Control Solenoid Electrical - Circuit short to ground
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2759-15 Torque Converter Clutch Pressure Control Solenoid Electrical - Circuit short to battery or open
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2783-98 Torque Converter Temperature Too High - Component or system over temperature
  • Transmission control module is not configured correctly
  • Using the Jaguar Land Rover approved diagnostic equipment, re-configure the transmission control module with the latest level software and retest. If the fault persists, install a new transmission control module
P2787-4B Clutch Temperature Too High - Over temperature
  • Automatic transmission internal temperature above maximum threshold
NOTE: This DTC may be induced by performing an excessive number of gear shifts using the paddle switches.
  • Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, refer to the relevant article of the repair information and check the automatic transmission fluid level and quality. Check the paddle switches for uncommanded operation. Rectify as necessary
P2793-64 Gear Shift Direction Circuit - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P2793-94 Gear Shift Direction Circuit - Unexpected operation
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
P279D-64 Four Wheel Drive (4WD) Range Signal Circuit - Signal plausibility failure
  • Transfer case system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transfer case control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
P279D-86 Four Wheel Drive (4WD) Range Signal Circuit - Signal invalid
  • Transfer case system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transfer case control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0028-88 Vehicle Communication Bus A - Bus off
  • High speed CAN bus (powertrain) circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the appropriate system wiring diagrams and check the high speed CAN bus (powertrain) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
U0080-88 Vehicle Communication Bus F - Bus off
  • FlexRay bus circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the appropriate system wiring diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
U0100-87 Lost Communication With ECM/PCM A - Missing message
  • Powertrain control module power or ground circuit open circuit, high resistance
  • FlexRay bus circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Engine system fault
  • Refer to the appropriate system wiring diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the appropriate system wiring diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0102-87 Lost Communication With Transfer Case Control Module - Missing message
  • Transfer case control module power or ground circuit open circuit, high resistance
  • FlexRay bus circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Transfer case system fault
  • Refer to the appropriate system wiring diagrams and check the transfer case control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the appropriate system wiring diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transfer case control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0103-87 Lost Communication With Gear Shift Control Module A - Missing message
  • Transmission control switch power or ground circuit open circuit, high resistance
  • High speed CAN bus (powertrain) circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Transmission control switch system fault
  • Refer to the appropriate system wiring diagrams and check the transmission control switch power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the appropriate system wiring diagrams and check the high speed CAN bus (powertrain) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0121-87 Lost Communication With Anti-Lock Brake System (ABS) Control Module - Missing message
  • Anti-lock brake system control module power or ground circuit open circuit, high resistance
  • FlexRay bus circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Anti-lock brake system fault
  • Refer to the appropriate system wiring diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the appropriate system wiring diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0140-87 Lost Communication With Body Control Module - Missing message
  • Body control module power or ground circuit open circuit, high resistance
  • FlexRay bus circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Body system fault
  • Refer to the appropriate system wiring diagrams and check the body control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the appropriate system wiring diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0146-87 Lost Communication With Gateway A - Missing message
  • Gateway module power or ground circuit open circuit, high resistance
  • FlexRay bus circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Gateway system fault
  • Refer to the appropriate system wiring diagrams and check the gateway module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the appropriate system wiring diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, check the gateway module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0302-57 Software Incompatibility with Transmission Control Module - Invalid/incomplete software component
  • Transmission control module is not configured correctly
  • Using the Jaguar Land Rover approved diagnostic equipment, re-configure the transmission control module with the latest level software
U0302-64 Software Incompatibility with Transmission Control Module - Signal plausibility failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
U0401-02 Invalid Data Received From ECM/PCM A - General signal failure
  • Engine system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0401-64 Invalid Data Received From ECM/PCM A - Signal plausibility failure
  • Engine system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0401-82 Invalid Data Received From ECM/PCM A - Alive/sequence counter incorrect/not updated
  • Engine system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0401-83 Invalid Data Received From ECM/PCM A - Value of signal protection calculation incorrect
  • Engine system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0403-82 Invalid Data Received From Transfer Case Control Module - Alive/sequence counter incorrect/not updated
  • Transfer case system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transfer case control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0403-83 Invalid Data Received From Transfer Case Control Module - Value of signal protection calculation incorrect
  • Transfer case system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transfer case control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0404-64 Invalid Data Received From Gear Shift Control Module A - Signal plausibility failure
  • Transmission control switch system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0404-82 Invalid Data Received From Gear Shift Control Module A - Alive/sequence counter incorrect/not updated
  • Transmission control switch system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0404-83 Invalid Data Received From Gear Shift Control Module A - Value of signal protection calculation incorrect
  • Transmission control switch system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0415-82 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module - Alive/sequence counter incorrect/not updated
  • Anti-lock brake system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0415-83 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module - Value of signal protection calculation incorrect
  • Anti-lock brake system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0415-86 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module - Signal invalid
  • Anti-lock brake system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0422-82 Invalid Data Received From Body Control Module - Alive/sequence counter incorrect/not updated
  • Body system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0422-83 Invalid Data Received From Body Control Module - Value of signal protection calculation incorrect
  • Body system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U2300-54 Central Configuration - Missing calibration
  • Car configuration file mismatch with vehicle specification
  • Gateway system fault
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s).
  • Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
  • Using the Jaguar Land Rover approved diagnostic equipment, check the gateway module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U2300-64 Central Configuration - Signal plausibility failure
  • Car configuration file mismatch with vehicle specification
  • Gateway system fault
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s).
  • Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
  • Using the Jaguar Land Rover approved diagnostic equipment, check the gateway module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U3000-56 Control Module - Invalid/incomplete configuration
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
U3001-47 Control Module Improper Shutdown - Watchdog/safety microcontroller failure
  • Transmission control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new transmission control module
scientia non olet · About LEMON Manuals