LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2018 >> Range Rover Velar Base >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Diagnostic Trouble Code Index DTC: Transfer Case Control Module (TCCM) -- Range Rover Velar/L560 >> General Information >> Description And Operation >> Diagnostic Trouble Code Index - DTC: Transfer Case Control Module (TCCM) (G2248463) >> Transfer Case Control Module (TCCM)

Transfer Case Control Module (TCCM)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT  acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTE:
  • Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
  • If a control module or a component is at fault or may be at fault and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new module/component.
  • Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).
  • When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
  • Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
  • Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
  • If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
  • Check JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and complete the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be set in the Transfer Case Control Module (TCCM). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing service information. For additional information, Refer to: DIAGNOSIS AND TESTING .

DTC DESCRIPTION POSSIBLE CAUSES ACTION
P0560-16 System Voltage - Circuit voltage below threshold
  • Transfer case control module power or ground circuit open circuit, high resistance
  • Battery/charging system fault
  • Transfer case control module internal failure
  • Refer to the electrical circuit diagrams and check the transfer case control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the relevant service information and check the battery and charging system. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P0560-17 System Voltage - Circuit voltage above threshold
  • Battery/charging system fault
  • Transfer case control module internal failure
  • Refer to the relevant service information and check the battery and charging system. Rectify as necessary
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P0601-42 Internal Control Module Memory Checksum Error - General memory failure
  • Transfer case control module is not configured correctly
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, reconfigure the transfer case control module with the latest level software
P0601-43 Internal Control Module Memory Checksum Error - Special memory failure
  • Transfer case control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P0603-09 Internal Control Module Keep Alive Memory (KAM) Error - Component failures
  • Transfer case control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P0634-68 Control Module Internal Temperature "A" Too High - Event information
  • Transfer case control module cooling airflow obstructed
  • Exhaust system damaged
  • Transfer case control module internal failure
NOTE:
  • This DTC is set when the transfer case control module internal temperature exceeds the maximum threshold.
  • This DTC may be induced by prolonged driving on a poor traction surface.
  • Check the transfer case control module cooling airflow for obstructions (mud packing, etc). Rectify as necessary
  • Check the exhaust system for damage which may be directing hot exhaust gasses towards the transfer case. Rectify as necessary
  • Allow the system temperature to return to normal. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P0668-68 Control Module Internal Temperature Sensor "A" Circuit Low - Event information
  • Transfer case control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P1240-96 Sensor Power Supply - Component internal failure
  • Transfer case control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
P1889-18 Oil Pressure Pump Performance - Circuit current below threshold
  • Transfer case fluid level low
  • Transfer case actuator circuit open circuit, high resistance
  • Transfer case control module internal failure
P1889-19 Oil Pressure Pump Performance - Circuit current above threshold
  • Transfer case actuator circuit short circuit to ground, short circuit to power
  • Transfer case actuator internal failure
  • Transfer case internal failure
  • Transfer case control module internal failure
  • Clear the DTC and retest. If the fault persists, refer to the electrical circuit diagrams and check the transfer case actuator circuit for short circuit to ground, short circuit to power. Repair the wiring as necessary
  • If the fault persists, or there are no wiring faults present, install a new transfer case actuator. Drain and refill the transfer case and bleed the pump. Clear the DTC and retest
  • Refer to SYMPTOM CHART for actions associated with the message - Traction Reduced - 2 Wheel Drive Only - and continue to the pinpoint tests as necessary
P1889-1F Oil Pressure Pump Performance - Circuit intermittent
  • Transfer case fluid level low
  • Transfer case actuator circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the relevant service information and check the transfer case fluid level. Rectify any leaks as necessary. Drain and refill the transfer case with the specified grade and volume of fluid
  • Clear the DTC and retest. If the fault persists, refer to the electrical circuit diagrams and check the transfer case actuator circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • If the fault persists, or there are no wiring faults present, install a new transfer case actuator. Drain and refill the transfer case and bleed the pump. Clear the DTC and retest
  • Refer to SYMPTOM CHART for actions associated with the message - Traction Reduced - 2 Wheel Drive Only - and continue to the pinpoint tests as necessary
P188E-11 Oil Pressure Pump Control Circuit - Circuit short to ground
  • Transfer case actuator circuit short circuit to ground
  • Clear the DTC and retest. If the fault persists, refer to the electrical circuit diagrams and check the transfer case actuator circuit for short circuit to ground, short circuit to power. Repair the wiring as necessary
  • If the fault persists, or there are no wiring faults present, install a new transfer case actuator. Drain and refill the transfer case and bleed the pump. Clear the DTC and retest
  • Refer to SYMPTOM CHART for actions associated with the message - Traction Reduced - 2 Wheel Drive Only - and continue to the pinpoint tests as necessary
P188E-12 Oil Pressure Pump Control Circuit - Circuit short to battery
  • Transfer case actuator circuit short circuit to power
  • Refer to the electrical circuit diagrams and check the transfer case actuator circuit for short circuit to power. Repair the wiring harness or install a new transfer case actuator as necessary
  • Refer to SYMPTOM CHART for actions associated with the message - Traction Reduced - 2 Wheel Drive Only - and continue to the pinpoint tests as necessary
P188E-13 Oil Pressure Pump Control Circuit - Circuit open
  • Transfer case actuator circuit open circuit, high resistance
  • Refer to the electrical circuit diagrams and check the transfer case actuator circuit for open circuit, high resistance. Repair the wiring harness or install a new transfer case actuator as necessary
P215A-62 Vehicle Speed - Wheel Speed Correlation - Signal compare failure
  • Anti-lock brake system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related DTCs and refer to the relevant DTC index
U0001-81 High Speed CAN Communication Bus - Invalid serial data received
  • Invalid data received from another control module through the high speed CAN bus (chassis)
  • Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect/not updated
  • Invalid data received from another control module through the high speed CAN bus (chassis)
  • Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-83 High Speed CAN Communication Bus - Value of signal protection calculation incorrect
  • Invalid data received from another control module through the high speed CAN bus (chassis)
  • Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-86 High Speed CAN Communication Bus - Signal invalid
  • Invalid signal received from another control module through the high speed CAN bus (chassis)
  • Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid signal source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-87 High Speed CAN Communication Bus - Missing message
  • Missing message from another control module through the high speed CAN bus (chassis)
  • Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the missing message source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-88 High Speed CAN Communication Bus - Bus off
  • High speed CAN bus (chassis) circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (chassis) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
U0300-46 Internal Control Module Software Incompatibility - Calibration/parameter memory failure
  • Transfer case control module is not configured correctly
  • Incorrect transfer case control module installed
  • Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transfer case control module with the latest level software
  • Check the part number of the transfer case control module. Install a new transfer case control module as necessary
U0300-4A Internal Control Module Software Incompatibility - Incorrect component installed
  • Transfer case control module is not configured correctly
  • Incorrect transfer case control module installed
  • Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transfer case control module with the latest level software
  • Check the part number of the transfer case control module. Install a new transfer case control module as necessary
U201A-57 Control Module Main Calibration Data - Invalid/incomplete software component
  • Transfer case control module is not configured correctly
  • Incorrect transfer case control module installed
  • Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transfer case control module with the latest level software
  • Check the part number of the transfer case control module. Install a new transfer case control module as necessary
U2300-43 Central Configuration - Special memory failure
  • Transfer case control module internal failure
  • Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
U2300-54 Central Configuration - Missing calibration
  • Car configuration file mismatch with vehicle specification
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs.
  • Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and perform routine - On Demand Self Test
U2300-55 Central Configuration - Not configured
  • Car configuration file mismatch with vehicle specification
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs.
  • Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and perform routine - On Demand Self Test
U2300-56 Central Configuration - Invalid/incomplete configuration
  • Car configuration file mismatch with vehicle specification
  • Transfer case control module is not configured correctly
NOTE:
  • After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs.
  • If U2300-64 is also set, perform the corrective actions for U2300-56 first and retest.
  • Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and perform routine - On Demand Self Test
  • Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transfer case control module with the latest level software
U2300-64 Central Configuration - Signal plausibility failure
  • Car configuration file mismatch with vehicle specification
  • Incorrect transfer case control module installed
NOTE:
  • After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs.
  • If U2300-56 is also set, perform the corrective actions for U2300-56 first and retest.
  • Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and perform routine - On Demand Self Test
  • Check the part number of the transfer case control module. Install a new transfer case control module as necessary
U3000-04 Control Module - System internal failures
  • Transfer case control module is not configured correctly
  • Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transfer case control module with the latest level software and perform routine - On Demand Self Test. If the fault persists, install a new transfer case control module
scientia non olet · About LEMON Manuals