Camera Control Module (CCM)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTE:

Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures information, or determine if any prior approval programme is in operation, prior to the installation of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the Jaguar Land Rover approved diagnostic equipment).
When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
Check JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and carry out the recommendations as required.

The article below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Camera Control Module (CCM). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing article in the repair information. For additional information, Refer to: PARKING AID

DTC	DESCRIPTION	POSSIBLE CAUSES	ACTION
B100E-29	Video Input A Signal - Signal invalid	Video out circuit short circuit to ground, open circuit, high resistance	Refer to the appropriate system wiring diagrams and check the video out circuit for short circuit to ground, open circuit, high resistance. Replace the wiring harness as necessary, clear the DTC and retest
B108E-31	Display - No signal	Missing/invalid data from the infotainment master controller Camera control module internal failure	Using the Jaguar Land Rover approved diagnostic equipment, check the infotainment master controller for related DTCs and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, check the power and ground connections to the module for obvious damage. Replace the wiring harness as required. Clear the DTC and retest. If the fault persists, install a new camera control module
B12BD-18	Rear Camera - Circuit current below threshold	Rear proximity camera power or ground circuit open circuit, high resistance Rear proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the rear proximity camera power and ground circuits for open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear proximity camera
B12BD-19	Rear Camera - Circuit current above threshold	Rear proximity camera circuit short circuit to ground, short circuit to power Rear proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the rear proximity camera circuit for short circuit to ground, short circuit to power. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear proximity camera
B12BD-31	Rear Camera - No signal	Rear proximity camera low voltage differential signaling circuits short circuit to ground, short circuit to power, open circuit, high resistance Rear proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the rear proximity camera low voltage differential signaling circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear proximity camera
B12BD-49	Rear Camera - Internal electronic failure	Rear proximity camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear proximity camera
B12BE-18	Left Front Camera - Circuit current below threshold	Front proximity camera power or ground circuit open circuit, high resistance Front proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the front proximity camera power and ground circuits for open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new front proximity camera
B12BE-19	Left Front Camera - Circuit current above threshold	Front proximity camera circuit short circuit to ground, short circuit to power Front proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the front proximity camera circuit for short circuit to ground, short circuit to power. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new front proximity camera
B12BE-31	Left Front Camera - No signal	Front proximity camera low voltage differential signaling circuits short circuit to ground, short circuit to power, open circuit, high resistance Front proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the front proximity camera low voltage differential signaling circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new front proximity camera
B12BE-49	Left Front Camera - Internal electronic failure	Front proximity camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new front proximity camera
B12C0-18	Left Mirror Camera - Circuit current below threshold	Left mirror proximity camera power or ground circuit open circuit, high resistance Left mirror proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the left mirror proximity camera power and ground circuits for open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new left mirror proximity camera
B12C0-19	Left Mirror Camera - Circuit current above threshold	Left mirror proximity camera circuit short circuit to ground, short circuit to power Left mirror proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the left mirror proximity camera circuit for short circuit to ground, short circuit to power. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new left mirror proximity camera
B12C0-31	Left Mirror Camera - No signal	Left mirror proximity camera low voltage differential signaling circuits short circuit to ground, short circuit to power, open circuit, high resistance Left mirror proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the left mirror proximity camera low voltage differential signaling circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new left mirror proximity camera
B12C0-49	Left Mirror Camera - Internal electronic failure	Left mirror proximity camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new left mirror proximity camera
B12C1-18	Right Mirror Camera - Circuit current below threshold	Right mirror proximity camera power or ground circuit open circuit, high resistance Right mirror proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the right mirror proximity camera power and ground circuits for open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new right mirror proximity camera
B12C1-19	Right Mirror Camera - Circuit current above threshold	Right mirror proximity camera circuit short circuit to ground, short circuit to power Right mirror proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the right mirror proximity camera circuit for short circuit to ground, short circuit to power. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new right mirror proximity camera
B12C1-31	Right Mirror Camera - No signal	Right mirror proximity camera low voltage differential signaling circuits short circuit to ground, short circuit to power, open circuit, high resistance Right mirror proximity camera internal failure	Refer to the appropriate system wiring diagrams and check the right mirror proximity camera low voltage differential signaling circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new right mirror proximity camera
B12C1-49	Right Mirror Camera - Internal electronic failure	Right mirror proximity camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new right mirror proximity camera
U0001-81	High Speed CAN Communication Bus - Invalid serial data received	Invalid data received from another control module via the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-87	High Speed CAN Communication Bus - Missing message	Missing message from another control module via the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the missing message source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-88	High Speed CAN Communication Bus - Bus off	High speed CAN bus (comfort) circuit short circuit to ground, short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the appropriate system wiring diagrams and check the high speed CAN bus (comfort) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Replace the wiring harness as necessary
U0300-00	Internal Control Module Software Incompatibility - No sub type information	Camera control module is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the camera control module with the latest level software
U0400-29	Invalid Data Received - Signal invalid	Missing/invalid data from the infotainment master controller Missing/invalid data from the anti-lock brake system control module Missing/invalid data from the steering angle sensor module	Using the Jaguar Land Rover approved diagnostic equipment, check the infotainment master controller for related DTCs and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related DTCs and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, check the steering angle sensor module for related DTCs and refer to the relevant DTC index
U0439-29	Invalid Data Received From All Terrain Control Module - Signal invalid	Missing/invalid data from the all terrain control module	Using the Jaguar Land Rover approved diagnostic equipment, check the all terrain control module for related DTCs and refer to the relevant DTC index
U0447-29	Invalid Data Received From Gateway A - Signal invalid	Camera control module power circuit short circuit to power Missing/invalid data from the gateway module	Refer to the appropriate system wiring diagrams and check the camera control module power circuit for short circuit to power. Repair the wiring harness as necessary Using the Jaguar Land Rover approved diagnostic equipment, check the gateway module for related DTCs and refer to the relevant DTC index
U0448-29	Invalid Data Received From Gateway B - Signal invalid	Missing/invalid data from the left/right blindspot monitoring system control module	Using the Jaguar Land Rover approved diagnostic equipment, check the left/right blindspot monitoring system control module for related DTCs and refer to the relevant DTC index
U044A-29	Invalid Data Received From Gateway D - Signal invalid	Missing/invalid data from the transmission control switch Missing/invalid data from the anti-lock brake system control module	Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control switch for related DTCs and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related DTCs and refer to the relevant DTC index
U0533-29	Invalid Data Received From Side Obstacle Detection Control Module-Left - Signal invalid	Missing/invalid data from the left blindspot monitoring system control module	Using the Jaguar Land Rover approved diagnostic equipment, check the left blindspot monitoring system control module for related DTCs and refer to the relevant DTC index
U0534-29	Invalid Data Received From Side Obstacle Detection Control Module-Right - Signal invalid	Missing/invalid data from the right blindspot monitoring system control module	Using the Jaguar Land Rover approved diagnostic equipment, check the right blindspot monitoring system control module for related DTCs and refer to the relevant DTC index
U1A4B-05	Control Module Processor B - System programming failures	System programming failures	Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the camera control module with the latest level software
U1A4B-06	Control Module Processor B - Algorithm based failures	Soiling to front camera lens	Clean the front camera lens Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest
U1A4B-49	Control Module Processor B - Internal electronic failure	Camera control module internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new camera control module
U201A-51	Control Module Main Calibration Data - Not programmed	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary
U2023-41	Control Module Network Signal Calibration Data - General checksum failure	Camera control module internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new camera control module
U2100-00	Initial Configuration Not Complete - No sub type information	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary
U2101-00	Control Module Configuration Incompatible - No sub type information	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary
U2300-54	Central Configuration - Missing calibration	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest
U2300-55	Central Configuration - Not configured	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest
U2300-56	Central Configuration - Invalid/incomplete configuration	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest
U2300-64	Central Configuration - Signal plausibility failure	Car configuration file mismatch with vehicle specification Camera control module is not configured correctly	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the camera control module with the latest level software
U3000-46	Control Module - Calibration/parameter memory failure	Camera control module internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new camera control module
U3000-49	Control Module - Internal electronic failure	Camera control module internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new camera control module
U3000-98	Control Module - Component or system over temperature	Camera control module or system over temperature	NOTE: Consider environmental conditions before condemning the camera control module Allow the camera control module to cool. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new camera control module
U3006-16	Control Module Input Power A - Circuit voltage below threshold	Camera control module power or ground circuit open circuit, high resistance Battery/charging system fault	Refer to the appropriate system wiring diagrams and check the camera control module power and ground circuits for open circuit, high resistance Refer to the relevant article of the repair information and test the battery and charging system. Repair the wiring harness as necessary
U3006-17	Control Module Input Power A - Circuit voltage above threshold	Battery/charging system fault	Refer to the relevant article of the repair information and test the battery and charging system