DTC: Transmission Control Module (TCM) - BOSCH: DTC's

DTC	Description	Possible Causes	Action
P0121-86	Throttle/Pedal Position Sensor A Circuit Range/Performance - Signal invalid	Throttle position sensor wiring high resistance Throttle position sensor sensing circuits (Throttle position 1 or Throttle position 2) short circuit to power Throttle position sensor failure	Refer to the electrical circuit diagrams and check the throttle position sensor circuit. Check for engine management DTCs. Renew the sensor
P0219-86	Engine Overspeed Condition - Signal invalid	Engine speed implausible (too high or too low)	Check for related Engine Control Module DTCs
P0500-81	Vehicle Speed Sensor A - invalid serial data received	Vehicle speed signal not detected	Check for related Anti-lock Braking System DTCs
P0501-81	Vehicle Speed Sensor A Range/Performance - invalid serial data received	Range/Performance	Check for related Anti-lock Braking System DTCs
P0561-00	System Voltage Unstable - No sub type information	Power supply voltage is out of range when the engine is running	Check the battery and charging system. Refer to the relevant workshop manual section
P0562-21	System Voltage Low - Signal amplitude < minimum	Supply voltage to TCM very low	Check the battery condition and state of charge. Check the Transmission Control Module connector and supply circuits. Refer to the electrical circuit diagrams
P0563-22	System Voltage High - Signal amplitude > maximum	Power supply voltage is too high if the engine is running and there has been no jump-start or transmission limp-home event	Check the battery and charging system. Refer to the relevant workshop manual section. Check if the vehicle has been jump-started
P0601-41	Internal Control Module Memory Check Sum Error - general checksum failure	Checksum error	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0603-00	Internal Control Module Keep Alive Memory (KAM) Error - No sub type information	Keep-alive memory (KAM) error	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0605-41	Internal Control Module Read Only Memory (ROM) Error - General checksum failure	Read only memory (ROM) error	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policy and procedures manual if a module is suspect
P0613-00	TCM Processor - No sub type information	No sub type information	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-04	TCM Processor - system internal failures	Internal failure	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-06	TCM Processor - algorithm based failures	Software algorithm based failures	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-11	TCM Processor - Circuit short to ground	Internal circuit short to ground	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-12	TCM Processor - Circuit short to battery	Internal circuit short to power	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-13	TCM Processor - Circuit open	Internal circuit open circuit	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-14	TCM Processor - Circuit short to ground or open	Internal circuit short to ground or open circuit	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-21	TCM Processor - Signal amplitude < minimum	Signal amplitude < minimum	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module.
P0613-22	TCM Processor - Signal amplitude > maximum	Signal amplitude > minimum	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-26	TCM Processor - Signal rate of change below threshold	Signal rate of change below threshold	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-47	TCM Processor - watchdog/safety micro controller failure	Watchdog/safety Micro controller failure	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-49	TCM Processor - internal electronic failure	Internal electronic failure	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0613-68	TCM Processor - event information	Event information	Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P061B-61	Internal Control Module Torque Calculation Performance - Signal calculation failure	Transmission Control Module positive torque signal not valid	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policy and procedures manual if a module is suspect
P061B-65	Internal Control Module Torque Calculation Performance - Signal has too few transitions / events	Transmission Control Module positive torque signal not valid	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policy and procedures manual if a module is suspect
P062F-04	Internal Control Module EEPROM Error - system internal failures	EEPROM error	Check that the transit relay is not still installed. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0642-21	Sensor Reference Voltage A Circuit Low - Signal amplitude < minimum	Reference voltage circuit short circuit to ground Reference voltage circuit high resistance	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0643-22	Sensor Reference Voltage A Circuit High - Signal amplitude > maximum	Reference voltage circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0657-13	Actuator Supply Voltage A Circuit / Open - Circuit open	Supply voltage circuit open circuit	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0657-1C	Actuator Supply Voltage A Circuit / Open - Circuit voltage out of range	Supply circuit voltage out of range	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0658-11	Actuator Supply Voltage A Circuit Low - Circuit short to ground	Supply voltage circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0659-12	Actuator Supply Voltage A Circuit High - Circuit short to battery	Supply voltage circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0668-21	PCM / ECM / TCM Internal Temperature Sensor A Circuit Low - Signal amplitude < minimum	Module internal temperature too low Temperature sensor circuit high resistance Temperature sensor circuit short circuit to ground	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0669-22	ECM / ECM / TCM Internal Temperature Sensor A Circuit High - Signal amplitude > maximum	Module internal temperature too high Temperature sensor circuit short circuit to power	Check for engine overheating and cooling system faults. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0700-02	Transmission Control System (MIL Request) - General signal failure	General signal failure	This indicates more than one fault is present. Check all DTC's reported on the vehicle and resolve. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0700-22	Transmission Control System (MIL Request) - Signal amplitude > maximum	Emergency position not reachable	This indicates more than one fault is present. Check all DTC's reported on the vehicle and resolve. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0700-75	Transmission Control System (MIL Request) - Emergency position not reachable	Signal implausible	This indicates more than one fault is present. Check all DTC's reported on the vehicle and resolve. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0705-00	Transmission Range Sensor A Circuit (PRNDL Input) - No sub type information	Signal implausible	Check the gear selector mechanism connector and wiring. Check the gear selector cable setting. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0710-13	Transmission Fluid Temperature Sensor A Circuit - Circuit open	Transmission fluid temperature sensor circuit open circuit Temperature sensor fault	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0711-01	Transmission Fluid Temperature Sensor A Circuit Range/Performance - general electrical failure	Transmission fluid temperature sensor general electrical failure Temperature sensor fault	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0712-00	Transmission Fluid Temperature Sensor A Circuit Low - No sub type information	Sensor circuit: high resistance Sensor circuit: short circuit to ground	Refer to the guided diagnostic routine for this code on the approved diagnostic system
P0711-22	Transmission Fluid Temperature Sensor A Circuit Range/Performance - Signal amplitude > maximum	Transmission fluid temperature sensor signal amplitude greater than maximum Temperature sensor fault	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect
P0712-11	Transmission Fluid Temperature Sensor A Circuit Low - Circuit short to ground	Sensor circuit high resistance Sensor circuit short circuit to ground	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0713-12	Transmission Fluid Temperature Sensor A Circuit High - Circuit short to battery	Sensor circuit short circuit to power	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0716-14	Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Circuit short to ground or open	Sensor circuit high resistance Sensor circuit short circuit to ground	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0716-21	Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Signal amplitude < minimum	Turbine/input shaft speed sensor signal too small	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0716-22	Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Signal amplitude > maximum	Turbine/input shaft speed sensor signal too large	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0717-12	Turbine/Input Shaft Speed Sensor A Circuit No Signal - Circuit short to battery	Sensor circuit short circuit to power	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0720-12	Output Shaft Speed Sensor Circuit - Circuit short to battery	Sensor circuit short circuit to power	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0720-14	Output Shaft Speed Sensor Circuit - Circuit short to ground or open	Sensor circuit high resistance Sensor circuit short circuit to ground	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0721-22	Output Shaft Speed Sensor Circuit Range/Performance - Signal amplitude > maximum	Signal amplitude above maximum Range/performance	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0721-27	Output Shaft Speed Sensor Circuit Range/Performance - Signal rate of change above threshold	Signal rate of change above threshold	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0721-64	Output Shaft Speed Sensor Circuit Range/Performance - Signal plausibility failure	Signal plausibility failure	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0729-00	Gear 6 Incorrect Ratio - No sub type information - No sub type information - No sub type information	Incorrect ratio Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0730-00	Incorrect Gear Ratio - No sub type information	Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0731-00	Gear 1 Incorrect Ratio - No sub type information	Incorrect ratio Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0732-00	Gear 2 Incorrect Ratio - No sub type information	Incorrect ratio Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0733-00	Gear 3 Incorrect Ratio - No sub type information	Incorrect ratio Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission.
P0734-00	Gear 4 Incorrect Ratio - No sub type information	Incorrect ratio Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0735-00	Gear 5 Incorrect Ratio - No sub type information	Incorrect ratio Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0736-62	Reverse Incorrect Ratio - Signal compare failure	Slip too high between input and output shaft speeds signal compare failure	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0736-64	Reverse Incorrect Ratio - Signal plausibility failure	Slip too high between input and output shaft speeds	Check the transmission oil level and quality. Adjust as necessary. Clear the DTC and retest. If the problem persists, renew the transmission (sensor is internal). Refer to the warranty policies and procedures before renewing the transmission
P0740-13	Torque Converter Clutch Solenoid Circuit / Open - Circuit open	Solenoid circuit high resistance	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0741-07	Torque Converter Clutch Solenoid Circuit Performance/Stuck Off - mechanical failures	Solenoid circuit stuck off Slip too high at torque converter clutch	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0748-21	Pressure Control Solenoid A Electrical - Signal amplitude < minimum	Solenoid signal amplitude < minimum	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0748-22	Pressure Control Solenoid A Electrical - Signal amplitude > maximum	Solenoid signal amplitude > minimum	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0751-13	Shift Solenoid A Performance/Stuck Off - Circuit open	Performance Stuck off Solenoid circuit high resistance	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0751-14	Shift Solenoid A Performance/Stuck Off - Circuit short to ground or open	Performance Stuck off Solenoid circuit high resistance Solenoid circuit short circuit to ground	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0752-11	Shift Solenoid A Stuck On - Circuit short to ground	Stuck on Solenoid valve short circuit to ground	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0753-12	Shift Solenoid A Electrical - Circuit short to battery	Solenoid valve short circuit to power	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0778-21	Pressure Control Solenoid B Electrical - Signal amplitude < minimum	Pressure control solenoid signal amplitude < minimum	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0778-22	Pressure Control Solenoid B Electrical - Signal amplitude > maximum	Pressure control solenoid signal amplitude > minimum	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0780-00	Shift malfunction - No sub type information	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission
P0781-00	1 - 2 Shift - No sub type information	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission
P0781-62	1 - 2 Shift - Signal compare failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0781-64	1 - 2 Shift - Signal plausibility failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0782-22	2 - 3 Shift - Signal amplitude > maximum	Input/Output shaft ratio signal amplitude > minimum	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0782-26	2 - 3 Shift - Signal rate of change below threshold	Input/Output shaft ratio signal rate of change below threshold	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0782-62	2 - 3 Shift - Signal compare failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0782-64	2 - 3 Shift - Signal plausibility failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0783-00	3 - 4 Shift - No sub type information	Input/Output shaft ratio too high during a shift Clutch does not open	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0783-00	3 - 4 Shift - no sub type information	No sub type information	Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission
P0783-23	3 - 4 Shift - Signal stuck low	Input/Output shaft ratio too high during a shift Clutch does not open	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0783-62	3 - 4 Shift - Signal compare failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0783-64	3 - 4 Shift - Signal plausibility failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0784-00	4 - 5 Shift - No sub type information	No sub type information	Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission
P0784-23	4 - 5 Shift - Signal stuck low	Input/Output shaft ratio too high during a shift Clutch does not open	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0784-62	4 - 5 Shift - Signal compare failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0784-64	4 - 5 Shift - Signal plausibility failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0798-21	Pressure Control Solenoid C Electrical - Signal amplitude < minimum	Pressure control solenoid signal amplitude < minimum	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0798-22	Pressure Control Solenoid C Electrical - Signal amplitude > maximum	Pressure control solenoid signal amplitude > maximum	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P081C-62	Park Input Circuit - Signal compare failure	Park lock signal compare failure	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P081C-64	Park Input Circuit - Signal plausibility failure	Park lock signal plausibility failure	Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0826-26	Up and Down Switch Circuit - Signal rate of change below threshold	Implausible signal	Refer to the electrical guides and check the circuit between the gear selector mechanism and the Transmission Control Module. Check the switch operation of the transmission shift selector
P0829-23	5-6 Shift - Signal stuck low	Input/Output shaft ratio too high during a shift Clutch does not open	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0829-62	5-6 Shift - Signal compare failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0829-64	5-6 Shift - Signal plausibility failure	Input/Output shaft ratio too high during a shift Clutch does not open or close	Check the fluid level and condition. Adjust as necessary. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission. Refer to the warranty policies and procedures before renewing a Transmission
P0850-29	Park / Neutral Switch Input Circuit - Signal invalid	Starter inhibit signal fault	Refer to the electrical circuit diagrams and check the park/neutral switch circuit between the central electronics module, the Engine Control Module and Transmission Control Module
P0897-00	Transmission Fluid Deteriorated - No sub type information	Temperature too high over too long a time Transmission temperature sensor fault	Check for transmission temperature sensor related DTCs. Check transmission oil cooler and repair/replace as necessary. Renew the transmission fluid
P0928-13	Gear Shift Lock Solenoid Control Circuit/Open - Circuit open	Shift interlock solenoid open circuit	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0929-14	Gear Shift Lock Solenoid Control Circuit Range/Performance - Circuit short to ground or open	Shift interlock solenoid short circuit to ground or open circuit	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0930-11	Gear Shift Lock Solenoid/Actuator Circuit A Low - Circuit short to ground	Shift interlock solenoid short circuit to ground	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0931-12	Gear Shift Lock Solenoid/Actuator Circuit A High - Circuit short to battery	Shift interlock solenoid short circuit to power	Refer to the electrical guides and check the circuit between the Transmission Control Module and the shift lock solenoid. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0938-29	Hydraulic Oil Temperature Sensor Range/Performance - Signal invalid	Temperature sensor signal not plausible Transmission fluid temperature compared with module temperature fault	Check for engine overheating and cooling system faults. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0960-13	Pressure Control Solenoid A Control Circuit / Open - Circuit open	Control circuit high resistance	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0960-14	Pressure Control Solenoid A Control Circuit / Open - Circuit short to ground or open	Control circuit high resistance Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0962-11	Pressure Control Solenoid A Control Circuit Low - Circuit short to ground	Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0963-12	Pressure Control Solenoid A Control Circuit High - Circuit short to battery	Control circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0964-13	Pressure Control Solenoid B Control Circuit / Open - Circuit open	Control circuit high resistance	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0964-14	Pressure Control Solenoid B Control Circuit / Open - Circuit short to ground or open	Control circuit high resistance Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0966-11	Pressure Control Solenoid B Control Circuit Low - Circuit short to ground	Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0967-12	Pressure Control Solenoid B Control Circuit High - Circuit short to battery	Control circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0968-13	Pressure Control Solenoid C Control Circuit / Open - Circuit open	Control circuit open circuit	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0968-14	Pressure Control Solenoid C Control Circuit / Open - Circuit short to ground or open	Control circuit short circuit to ground or open circuit	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0970-11	Pressure Control Solenoid C Control Circuit Low - Circuit short to ground	Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P0971-12	Pressure Control Solenoid C Control Circuit High - Circuit short to battery	Control circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P1783-00	Transmission Over temperature Condition - No sub type information	Valve body module shut-down detected on last drive cycle	Check for engine overheating and cooling system faults. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the module. Consider environmental conditions before condemning the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2716-21	Pressure Control Solenoid D Electrical - Signal amplitude < minimum	Pressure control solenoid signal amplitude < minimum	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2716-22	Pressure Control Solenoid D Electrical - Signal amplitude > maximum	Pressure control solenoid signal amplitude > maximum	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2718-13	Pressure Control Solenoid D Control Circuit / Open - Circuit open	Control circuit open circuit	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2718-14	Pressure Control Solenoid D Control Circuit / Open - Circuit short to ground or open	Control circuit high resistance Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2720-11	Pressure Control Solenoid D Control Circuit Low - Circuit short to ground	Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission control
P2721-12	Pressure Control Solenoid D Control Circuit High - Circuit short to battery	Control circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2725-21	Pressure Control Solenoid E Electrical - Signal amplitude < minimum	Solenoid signal amplitude < minimum	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2725-22	Pressure Control Solenoid E Electrical - Signal amplitude > maximum	Solenoid signal amplitude > maximum	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2727-13	Pressure Control Solenoid E Control Circuit / Open - Circuit open	Control circuit open circuit	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2727-14	Pressure Control Solenoid E Control Circuit / Open - Circuit short to ground or open	Control circuit high resistance Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission control
P2729-11	Pressure Control Solenoid E Control Circuit Low - Circuit short to ground	Control circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2730-12	Pressure Control Solenoid E Control Circuit High - Circuit short to battery	Control circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2759-22	Torque Converter Clutch Pressure Control Solenoid Electrical - Signal amplitude > maximum	Pressure control solenoid fault	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2761-14	Torque Converter Clutch Pressure Control Solenoid Control Circuit / Open - Circuit short to ground or open	Pressure control solenoid circuit high resistance	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2762-21	Torque Converter Clutch Pressure Control Solenoid Control Circuit Range / Perf - Signal amplitude < minimum	Pressure control solenoid circuit current too low	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2763-12	Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Circuit short to battery	Pressure control solenoid circuit short circuit to power	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
P2764-11	Torque Converter Clutch Pressure Control Solenoid Control Circuit Low - Circuit short to ground	Pressure control solenoid circuit short circuit to ground	Check for other DTCs and rectify as necessary. Check the Transmission Control Module connector and the power/ground circuits to the Transmission Control Module. Clear the DTC and retest. If the problem persists, renew the module. Refer to the warranty policies and procedures before renewing a Transmission Control Module
U0001-88	High Speed CAN Communication CAN Bus - bus off	Bus off	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network
U0100-82	Lost Communication With ECM/PCM "A" - alive/sequence counter incorrect/not updated	Alive counter error	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Engine Control Module and Transmission Control Module
U0100-83	Lost Communication With ECM/PCM "A" - value of signal protection calculation incorrect	Checksum error	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Engine Control Module and Transmission Control Module
U0100-87	Lost Communication With ECM/PCM "A" - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Engine Control Module and Transmission Control Module
U0102-87	Lost Communication with Transfer Case Control Module - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Transfer Case Control Module and Transmission Control Module
U0103-87	Lost Communications with Gear Shift Module A - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Gear Shift Module and Transmission Control Module
U0122-82	Lost Communication With Vehicle Dynamics Control Module - alive/sequence counter incorrect/not updated	Alive counter error	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Anti-lock Braking System Module and Transmission Control Module
U0122-83	Lost Communication With Vehicle Dynamics Control Module - value of signal protection calculation incorrect	Checksum error	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Anti-lock Braking System Module and Transmission Control Module
U0122-87	Lost Communication With Vehicle Dynamics Control Module - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Anti-lock Braking System Module and Transmission Control Module
U0126-87	Lost Communication With Steering Angle Sensor Module - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Steering Angle Sensor and Transmission Control Module
U0128-87	Lost Communication With Park Brake Control Module - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Parking Brake Module and Transmission Control Module
U0155-82	Lost Communication With Instrument Panel Cluster (IPC) Control Module - alive/sequence counter incorrect/not updated	Alive counter error	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Instrument Cluster and Transmission Control Module
U0155-83	Lost Communication With Instrument Panel Cluster (IPC) Control Module - value of signal protection calculation incorrect	Checksum error	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Instrument Cluster and Transmission Control Module
U0155-87	Lost Communication With Instrument Panel Cluster (IPC) Control Module - missing message	Missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Instrument Cluster and Transmission Control Module
U0300-55	Internal Control Module Software Incompatibility - not configured	Module is not configured	Check for other modules reporting CAN Bus off or lost communication faults. If other modules report problems, check the software version in the Central Junction Box using the manufacturers approved diagnostic system. If no other modules report problems, check the software version in the Transmission Control Module. Update as necessary
U0401-86	Invalid Data Received from ECM/PCM A - Signal invalid	Signal invalid	Check for engine management system (EMS/PCM) DTCs. Refer to the relevant section in the workshop manual. Check the correct software version in the Engine Control Module using the manufacturers approved diagnostic system. Update as necessary
U0416-86	Invalid Data Received From Vehicle Dynamics Control Module - Signal invalid	Signal invalid	Check for other Anti-lock Braking System related DTCs. Check for other EMS related DTC faults (brake signal related). Check the Anti-lock Braking System control module installation/configuration and for correct software version using the manufacturers approved diagnostic system. Refer to the lost communication statement at the start of the Network Communications section in the workshop manual
U2023-86	Control Module Network Signal Calibration Data - Signal invalid	Engine torque information Fault received from external node	Check for engine management system (EMS/PCM) DTCs. Refer to the relevant section in the workshop manual. Check the control module for correct software version using the manufacturers approved diagnostic system
U3000-4A	Control Module - incorrect component installed	Incorrect component installed Mismatch between configuration data and read configuration	Check for other modules reporting CAN Bus off or lost communication faults. If other modules report problems, check the software version in the Central Junction Box using the manufacturers approved diagnostic system. If no other modules report problems, check the software version in the Transmission Control Module. Update as necessary
U3000-81	Control Module - invalid serial data received	Invalid serial data received	Check for other modules reporting CAN Bus off or lost communication faults. If other modules report problems, check the software version in the Central Junction Box using the manufacturers approved diagnostic system. If no other modules report problems, check the software version in the Transmission Control Module. Update as necessary