DTC: Restraints Control Module (RCM): DTC's

DTC	Description	Possible Cause	Action
B0001-11	Driver Frontal Stage 1 Deployment Control - circuit short to ground	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver Airbag Ignitor (Stage 1) circuit short to ground	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 1) circuit for short to ground Check for intermittent shorts to ground within the clockspring by rotating the steering column during the checks
B0001-12	Driver Frontal Stage 1 Deployment Control - circuit short to battery	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver Airbag Ignitor (Stage 1) circuit short to power	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 1) circuit for short to power Check for intermittent shorts to power within the clockspring by rotating the steering column during the checks
B0001-1A	Driver Frontal Stage 1 Deployment Control - circuit resistance below threshold	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver Airbag Ignitor (Stage 1) circuit resistance below threshold	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 1) circuit for short circuit (Check connector security at clockspring and airbag) Check for intermittent short circuits within the clockspring by rotating the steering column during the checks
B0001-1B	Driver Frontal Stage 1 Deployment Control - circuit resistance above threshold	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver Airbag Ignitor (Stage 1) high circuit resistance	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 1) circuit for high resistance or open circuit Check for intermittent open circuit, high resistance faults within the clockspring by rotating the steering column during the checks
B0001-64	Driver Frontal Stage 1 Deployment Control - signal plausibility failure	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver Airbag Ignitor (Stage 1) signal plausibility failure	Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0001-95	Driver Frontal Stage 1 Deployment Control - incorrect assembly	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver Airbag Ignitor (Stage 1) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 1) circuit for faults Check for intermittent short circuits within the clockspring by rotating the steering column during the checks
B0002-11	Driver Frontal Stage 2 Deployment Control - circuit short to ground	NOTE: Circuit reference DR AIRBAG F2 / DR AIRBAG R2 Driver Airbag Ignitor (Stage 2) circuit short to ground	Refer to the electrical circuit diagrams and test Driver Airbag Ignitor (Stage 2) circuit for short to ground Check for intermittent shorts to ground within the clockspring by rotating the steering column during the checks
B0002-12	Driver Frontal Stage 2 Deployment Control - circuit short to battery	Driver Airbag Ignitor (Stage 2) circuit short to power	Refer to the electrical circuit diagrams and test Driver Airbag Ignitor (Stage 2) circuit for short to power Check for intermittent shorts to power within the clockspring by rotating the steering column during the checks
B0002-1A	Driver Frontal Stage 2 Deployment Control - circuit resistance below threshold	NOTE: Circuit reference DR AIRBAG F2 / DR AIRBAG R2 Driver Airbag Ignitor (Stage 2) circuit resistance below threshold	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 2) circuit for short circuit (Check connector security at clockspring and airbag) Check for intermittent short circuits within the clockspring by rotating the steering column during the checks
B0002-1B	Driver Frontal Stage 2 Deployment Control - circuit resistance above threshold	NOTE: Circuit reference DR AIRBAG F2 / DR AIRBAG R2 Driver Airbag Ignitor (Stage 2) high circuit resistance	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 2) circuit for high resistance or open circuit Check for intermittent open circuit, high resistance faults within the clockspring by rotating the steering column during the checks
B0002-64	Driver Frontal Stage 2 Deployment Control - signal plausibility failure	NOTE: Circuit reference DR AIRBAG F2 / DR AIRBAG R2 Driver Airbag Ignitor (Stage 2) signal plausibility failure	Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0002-95	Driver Frontal Stage 2 Deployment Control - incorrect assembly	NOTE: Circuit reference DR AIRBAG F2 / DR AIRBAG R2 Driver Airbag Ignitor (Stage 2) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Driver Airbag Ignitor (Stage 2) circuit for faults Check for intermittent short circuits within the clockspring by rotating the steering column during the checks
B0010-11	Passenger Frontal Stage 1 Deployment Control - circuit short to ground	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Front Passenger Airbag Ignitor (Stage 1) circuit short to ground	Refer to the electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 1) circuit for short to ground
B0010-12	Passenger Frontal Stage 1 Deployment Control - circuit short to battery	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Front Passenger Airbag Ignitor (Stage 1) circuit short to power	Refer to the electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 1) circuit for short to power
B0010-1A	Passenger Frontal Stage 1 Deployment Control - circuit resistance below threshold	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Front Passenger Airbag Ignitor (Stage 1) circuit resistance below threshold	Refer to electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 1) circuit for short circuit (Check connectors for security)
B0010-1B	Passenger Frontal Stage 1 Deployment Control - circuit resistance above threshold	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Front Passenger Airbag Ignitor (Stage 1) high circuit resistance	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Refer to electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 1) circuit for high resistance or open circuit
B0010-64	Passenger Frontal Stage 1 Deployment Control - signal plausibility failure	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Front Passenger Airbag Ignitor (Stage 1) signal plausibility failure	Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0010-95	Passenger Frontal Stage 1 Deployment Control - incorrect assembly	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Front Passenger Airbag Ignitor (Stage 1) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 1) circuit for faults
B0011-11	Passenger Frontal Stage 2 Deployment Control - circuit short to ground	NOTE: Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Front Passenger Airbag Ignitor (Stage 2) circuit short to ground	Refer to the electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 2) circuit for short to ground
B0011-12	Passenger Frontal Stage 2 Deployment Control - circuit short to battery	NOTE: Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Front Passenger Airbag Ignitor (Stage 2) circuit short to power	Refer to the electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 2) circuit for short to power
B0011-1A	Passenger Frontal Stage 2 Deployment Control - circuit resistance below threshold	NOTE: Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Front Passenger Airbag Ignitor (Stage 2) circuit resistance below threshold	Refer to electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 2) circuit for short circuit (Check connectors for security)
B0011-1B	Passenger Frontal Stage 2 Deployment Control - circuit resistance above threshold	NOTE: Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Front Passenger Airbag Ignitor (Stage 2) high circuit resistance	Refer to electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 2) circuit for high resistance or open circuit
B0011-64	Passenger Frontal Stage 2 Deployment Control - signal plausibility failure	NOTE: Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Front Passenger Airbag Ignitor (Stage 2) signal plausibility failure	Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0011-95	Passenger Frontal Stage 2 Deployment Control - incorrect assembly	NOTE: Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Front Passenger Airbag Ignitor (Stage 2) Incorrect assembly short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Front Passenger Airbag Ignitor (Stage 2) circuit for faults
B0020-11	Left Side Air Bag Deployment Control - circuit short to ground	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Left Side Airbag Ignitor circuit short to ground	Refer to the electrical circuit diagrams and test Driver (LHD) / Passenger (RHD) Side Airbag Ignitor circuit for short to ground
B0020-12	Left Side Air Bag Deployment Control - circuit short to battery	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Left Side Airbag Ignitor circuit short to power	Refer to the electrical circuit diagrams and test Driver (LHD) / Passenger (RHD)Side Airbag Ignitor circuit for short to power
B0020-1A	Left Side Air Bag Deployment Control - circuit resistance below threshold	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Left Side Airbag Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and test Driver (LHD) / Passenger (RHD) Side Airbag Ignitor circuit for short circuit (Check connectors for security)
B0020-1B	Left Side Air Bag Deployment Control - circuit resistance above threshold	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Left Side Airbag Ignitor high circuit resistance	Refer to electrical circuit diagrams and test Driver (LHD) / Passenger (RHD) Side Airbag Ignitor circuit for high resistance or open circuit
B0020-64	Left Side Air Bag Deployment Control - signal plausibility failure	Signal plausibility failure	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0020-95	Left Side Airbag Deployment Control - incorrect assembly	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Driver (LHD) / Passenger (RHD) Side Airbag Ignitor circuit for faults
B0021-11	Left Curtain Deployment Control 1 - circuit short to ground	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Left hand Curtain Ignitor circuit short to ground	Refer to the electrical circuit diagrams and test Left Side Curtain Ignitor circuit for short to ground
B0021-12	Left Curtain Deployment Control 1 - circuit short to battery	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Left hand Curtain Ignitor circuit short to power	Refer to the electrical circuit diagrams and test Left Side Curtain Ignitor circuit for short to power
B0021-1A	Left Curtain Deployment Control 1 - circuit resistance below threshold	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Left hand Curtain Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and test Left Side Curtain Ignitor circuit for short circuit (Check connectors for security)
B0021-1B	Left Curtain Deployment Control 1 - circuit resistance above threshold	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Left hand Curtain Ignitor high circuit resistance, open circuit	Refer to electrical circuit diagrams and test Left Side Curtain Ignitor circuit for high resistance or open circuit
B0021-64	Left Curtain Deployment Control 1 - signal plausibility failure	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Left hand Curtain Ignitor configuration error	Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0021-95	Left Curtain Deployment Control 1 - incorrect assembly	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Left Side Curtain Ignitor circuit for faults
B0022-11	Left Curtain Deployment Control 2 - circuit short to ground	Left hand Curtain Ignitor circuit short to ground	NOTE: Applicable to seven seat vehicles. Refer to the electrical circuit diagrams and test Left Side Curtain (Row 3) Ignitor circuit for short to ground
B0022-12	Left Curtain Deployment Control 2 - circuit short to battery	Left hand Curtain Ignitor circuit short to power	NOTE: Applicable to seven seat vehicles. Refer to the electrical circuit diagrams and test Left Side Curtain (Row 3) Ignitor circuit for short to power
B0022-1A	Left Curtain Deployment Control 2 - circuit resistance below threshold	Left hand Curtain Ignitor circuit resistance below threshold	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and test Left Side Curtain (Row 3) Ignitor circuit for short circuit (Check connectors for security)
B0022-1B	Left Curtain Deployment Control 2 - circuit resistance above threshold	Left hand Curtain Ignitor high circuit resistance, open circuit	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and test Left Side Curtain (Row 3) Ignitor circuit for high resistance or open circuit
B0022-64	Left Curtain Deployment Control 2 - signal plausibility failure	Left hand Curtain Ignitor configuration error	NOTE: Applicable to seven seat vehicles. Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0022-95	Left Curtain Deployment Control 2 - incorrect assembly	Incorrect assembly - short circuit between two different circuits (at least two faults)	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and test Left Side Curtain (Row 3) Ignitor circuit for faults
B0028-11	Right Side Air Bag Deployment Control - circuit short to ground	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 Right side air bag circuit - short to ground	Refer to the electrical circuit diagrams and test Right Side Airbag Ignitor circuit for short to ground
B0028-12	Right Side Air Bag Deployment Control - circuit short to battery	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 Right side air bag circuit - short to power	Refer to the electrical circuit diagrams and test Right Side Airbag Ignitor circuit for short to power
B0028-1A	Right Side Air Bag Deployment Control - circuit resistance below threshold	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 Circuit resistance below threshold	Refer to electrical circuit diagrams and test Right Side Airbag Ignitor circuit for short circuit (Check connectors for security)
B0028-1B	Right Side Air Bag Deployment Control - circuit resistance above threshold	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 High Circuit Resistance	Refer to electrical circuit diagrams and test Right Side Airbag Ignitor circuit for high resistance or open circuit
B0028-64	Right Side Air Bag Deployment Control - signal plausibility failure	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 Signal plausibility failure	Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0028-95	Right Side Airbag Deployment Control - incorrect assembly	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Right Side Airbag Ignitor circuit for faults
B0029-11	Right Curtain Deployment Control 1 - circuit short to ground	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Right Curtain Ignitor circuit short to ground	Refer to the electrical circuit diagrams and check Right Curtain Ignitor circuit for short to ground
B0029-12	Right Curtain Deployment Control 1 - circuit short to battery	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Right Curtain Ignitor circuit short to power	Refer to the electrical circuit diagrams and check Right Curtain Ignitor circuit for short to power
B0029-1A	Right Curtain Deployment Control 1 - circuit resistance below threshold	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Right Curtain Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and check Right Curtain Ignitor circuit for short circuit (Check connectors for security)
B0029-1B	Right Curtain Deployment Control 1 - circuit resistance above threshold	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Right Curtain Ignitor high circuit resistance	Refer to electrical circuit diagrams and check Right Curtain Ignitor circuit for high resistance or open circuit
B0029-64	Right Curtain Deployment Control 1 - signal plausibility failure	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Right Curtain Ignitor configuration error	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0029-95	Right Curtain Deployment Control 1 - incorrect assembly	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Right Curtain Ignitor circuit for faults
B002A-11	Right Curtain Deployment Control 2 - circuit short to ground	Right Curtain Ignitor circuit short to ground	NOTE: Applicable to seven seat vehicles. Refer to the electrical circuit diagrams and test Right Side Curtain (Row 3) Ignitor circuit for short to ground
B002A-12	Right Curtain Deployment Control 2 - circuit short to battery	Right Curtain Ignitor circuit short to power	NOTE: Applicable to seven seat vehicles. Refer to the electrical circuit diagrams and test Right Side Curtain (Row 3) Ignitor circuit for short to power
B002A-1A	Right Curtain Deployment Control 2 - circuit resistance below threshold	Right Curtain Ignitor circuit resistance below threshold	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and test Right Side Curtain (Row 3) Ignitor circuit for short circuit (Check connectors for security)
B002A-1B	Right Curtain Deployment Control 2 - circuit resistance above threshold	Right Curtain Ignitor high circuit resistance	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and test Right Side Curtain (Row 3) Ignitor circuit for high resistance or open circuit
B002A-64	Right Curtain Deployment Control 2 - signal plausibility failure	Right Curtain Ignitor configuration error	NOTE: Applicable to seven seat vehicles. Configuration error- This output has been switched off but the Airbag is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B002A-95	Right Curtain Deployment Control 2 - incorrect assembly	Incorrect assembly - short circuit between two different circuits (at least two faults)	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and test Right Side Curtain (Row 3) Ignitor circuit for faults
B0050-11	Driver Seatbelt Sensor - circuit short to ground	NOTE: Circuit reference BUCKLE SWITCH-DR Driver Seatbelt Switch circuit - short to ground	Refer to the electrical circuit diagrams and test Driver Seatbelt Switch circuit for short to ground
B0050-12	Driver Seatbelt Sensor - circuit short to battery	NOTE: Circuit reference BUCKLE SWITCH-DR Driver Seatbelt Switch circuit - short to power	Refer to the electrical circuit diagrams and test Driver Seatbelt Switch circuit for short to power
B0050-1D	Driver Seatbelt Sensor - circuit current out of range	NOTE: Circuit reference BUCKLE SWITCH-DR Circuit current out of range	Refer to the electrical circuit diagrams and test Driver Seatbelt Switch circuit for fault
B0050-64	Driver Seatbelt Sensor - signal plausibility failure	NOTE: Circuit reference BUCKLE SWITCH-DR Signal plausibility failure	Configuration error- This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0090-11	Left Frontal Restraints Sensor - circuit short to ground	NOTE: Circuit reference LH CRASH SENS F / LH CRASH SENS R LH Front Crash Sensor circuit - short to ground	Refer to the electrical circuit diagrams and test LH Front Crash Sensor circuit for short to ground
B0090-12	Left Frontal Restraints Sensor - circuit short to battery	NOTE: Circuit reference LH CRASH SENS F / LH CRASH SENS R LH Front Crash Sensor circuit - short to power	Refer to the electrical circuit diagrams and test LH Front Crash Sensor circuit for short to power
B0090-64	Left Frontal Restraints Sensor - signal plausibility failure	NOTE: Circuit reference LH CRASH SENS F / LH CRASH SENS R Signal plausibility failure	Configuration error- This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0090-81	Left Frontal Restraints Sensor - invalid serial data received	NOTE: Circuit reference LH CRASH SENS F / LH CRASH SENS R LH Front Crash Sensor - open circuit Sensor fault	Refer to the electrical circuit diagrams and test LH Front Crash Sensor circuit for open circuit fault. Install a new sensor as necessary
B0090-92	Left Frontal Restraints Sensor - performance or incorrect operation	NOTE: Circuit reference LH CRASH SENS F / LH CRASH SENS R Performance or incorrect operation	Check component fixings for security. If secure suspect LH Front Crash Sensor internal fault
B0090-96	Left Frontal Restraints Sensor - component internal failure	NOTE: Circuit reference LH CRASH SENS F / LH CRASH SENS R Component internal failure	Suspect LH Front Crash Sensor internal fault
B0091-11	Left Side Restraints Sensor 1 - circuit short to ground	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Left hand Side Crash Sensor 1 circuit short to ground	Refer to the electrical circuit diagrams and check left hand Side Crash 1 (Door) Sensor circuit for short to ground
B0091-12	Left Side Restraints Sensor 1 - circuit short to battery	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Left hand Side Crash Sensor 1 circuit short to power	Refer to the electrical circuit diagrams and check left hand Side Crash Sensor 1 (Door) circuit for short to power
B0091-64	Left Side Restraints Sensor 1 - signal plausibility failure	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Left hand Side Crash Sensor 1 configuration error	Configuration error - This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0091-81	Left Side Restraints Sensor 1 - invalid serial data received	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Left hand Side Crash Sensor 1 circuit open circuit Left hand Side Crash Sensor 1 failure	Refer to the electrical circuit diagrams and check left hand Side Crash Sensor 1(Door) circuit for open circuit fault. Check and install a new Left Side Restraints Sensor 1 (Door) as required. Refer to the warranty policy and procedures manual if a module is suspect
B0091-92	Left Side Restraints Sensor 1 - performance or incorrect operation	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Left hand Side Crash Sensor 1 component internal failure	Check and install a new left hand Side Restraints Sensor 1 (Door) as required. Refer to the warranty policy and procedures manual if a module is suspect
B0091-96	Left Side Restraints Sensor 1 - component internal failure	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Left hand Side Crash Sensor 1 component internal failure	Check and install a new left hand Side Restraints Sensor 1 (Door) as required. Refer to the warranty policy and procedures manual if a module is suspect
B0092-11	Left Side Restraints Sensor 2 - circuit short to ground	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 LH Side Crash Sensor circuit - short to ground	Refer to the electrical circuit diagrams and test LH Side Crash (B Pillar) Sensor circuit for short to ground
B0092-12	Left Side Restraints Sensor 2 - circuit short to battery	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 LH Side Crash Sensor circuit - short to power	Refer to the electrical circuit diagrams and test LH Side Crash Sensor (B Pillar) circuit for short to power
B0092-64	Left Side Restraints Sensor 2 - signal plausibility failure	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 LH Side Crash Sensor Signal plausibility failure	Configuration error - This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0092-81	Left Side Restraints Sensor 2 - invalid serial data received	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 LH Side Crash Sensor circuit - open circuit Sensor fault	Refer to the electrical circuit diagrams and test LH Side Crash Sensor circuit for open circuit fault. Install a new sensor as necessary
B0092-92	Left Side Restraints Sensor 2 - performance or incorrect operation	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Performance or incorrect operation	Suspect LH Side Crash (B Pillar) Sensor internal fault
B0092-96	Left Side Restraints Sensor 2 - component internal failure	NOTE: Circuit reference LH SIDE SENS F1 / LH SIDE SENS R1 Component internal failure	Suspect LH Side Crash Sensor (B Pillar) internal fault
B0093-11	Left Side Restraints Sensor 3 - circuit short to ground	NOTE: Circuit reference LH SIDE SENS F2 / LH SIDE SENS R2 Left hand Rear Side Crash Sensor 3 circuit short to ground	Refer to the electrical circuit diagrams and check left hand Rear Side Crash Sensor 3 circuit for short to ground
B0093-12	Left Side Restraints Sensor 3 - circuit short to battery	NOTE: Circuit reference LH SIDE SENS F2 / LH SIDE SENS R2 Left hand Rear Side Crash Sensor 3 circuit short to power	Refer to the electrical circuit diagrams and check left hand Rear Side Crash Sensor 3 circuit for short to power
B0093-64	Left Side Restraints Sensor 3 - signal plausibility failure	NOTE: Circuit reference LH SIDE SENS F2 / LH SIDE SENS R2 Left hand Rear Side Crash Sensor 3 configuration error	Configuration error - This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0093-81	Left Side Restraints Sensor 3 - invalid serial data received	NOTE: Circuit reference LH SIDE SENS F2 / LH SIDE SENS R2 Left hand Rear Side Crash Sensor 3 circuit - open circuit Left hand Rear Side Restraints Sensor 3 failure	Refer to the electrical circuit diagrams and check left hand Rear Side Crash Sensor 3 circuit for open circuit fault. Check and install a new left hand Rear Side Restraints Sensor 3 as required
B0093-92	Left Side Restraints Sensor 3 - performance or incorrect operation	NOTE: Circuit reference LH SIDE SENS F2 / LH SIDE SENS R2 Left hand Rear Side Crash Sensor 3 component internal failure	Check and install a new left hand Rear Side Restraints Sensor 3 as required. Refer to the warranty policy and procedures manual if a module is suspect
B0093-96	Left Side Restraints Sensor 3 - component internal failure	NOTE: Circuit reference LH SIDE SENS F2 / LH SIDE SENS R2 Left hand Rear Side Restraints Sensor 3 internal failure	Suspect left hand Rear Side Crash Sensor 3 internal fault. Check and install a new left hand Rear Side Restraints Sensor 3 as required. Refer to the warranty policy and procedures manual if a module is suspect
B0095-11	Right Frontal Restraints Sensor - circuit short to ground	NOTE: Circuit reference RH CRASH SENS F / RH CRASH SENS R RH Front Crash Sensor circuit - short to ground	Refer to the electrical circuit diagrams and test RH Front Crash Sensor circuit for short to ground
B0095-12	Right Frontal Restraints Sensor - circuit short to battery	NOTE: Circuit reference RH CRASH SENS F / RH CRASH SENS R RH Front Crash Sensor circuit - short to power	Refer to the electrical circuit diagrams and test RH Front Crash Sensor circuit for short to power
B0095-64	Right Frontal Restraints Sensor - signal plausibility failure	NOTE: Circuit reference RH CRASH SENS F / RH CRASH SENS R Signal plausibility failure	Configuration error - This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0095-81	Right Frontal Restraints Sensor - invalid serial data received	NOTE: Circuit reference RH CRASH SENS F / RH CRASH SENS R RH Front Crash Sensor - open circuit Sensor fault	Refer to the electrical circuit diagrams and test RH Front Crash Sensor circuit for open circuit fault. Install a new sensor as necessary
B0095-92	Right Frontal Restraints Sensor - performance or incorrect operation	NOTE: Circuit reference RH CRASH SENS F / RH CRASH SENS R Performance or incorrect operation	Check component fixings for security. If secure suspect RH Front Crash Sensor internal fault
B0095-96	Right Frontal Restraints Sensor - component internal failure	NOTE: Circuit reference RH CRASH SENS F / RH CRASH SENS R Component internal failure	Suspect RH Front Crash Sensor internal fault
B0096-11	Right Side Restraints Sensor 1 - circuit short to ground	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right hand Side Crash Sensor 1 circuit short to ground	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor (Door) circuit for short to ground
B0096-12	Right Side Restraints Sensor 1 - circuit short to battery	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right hand Side Crash Sensor 1 circuit short to power	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor (Door) circuit for short to power
B0096-64	Right Side Restraints Sensor 1 - signal plausibility failure	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right hand Side Crash Sensor 1 configuration error	Configuration error - This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0096-81	Right Side Restraints Sensor 1 - invalid serial data received	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right hand Side Crash Sensor 1 circuit open circuit Right Side Restraints Sensor 1 failure	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor circuit for open circuit fault. Check and install a new Right Side Restraints Sensor 1 (Door) as required. Refer to the warranty policy and procedures manual if a module is suspect
B0096-92	Right Side Restraints Sensor 1 - performance or incorrect operation	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right hand Side Crash Sensor 1 component internal failure	Check and install a new Right Side Restraints Sensor 1 (Door) as required. Refer to the warranty policy and procedures manual if a module is suspect
B0096-96	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right Side Restraints Sensor 1 - component internal failure	Right Side Crash Sensor 1 internal failure	Suspect right hand Side Crash Sensor (Door) internal fault. Check and install a new Right Side Restraints Sensor 1 as required. Refer to the warranty policy and procedures manual if a module is suspect
B0097-11	Right Side Restraints Sensor 2 - circuit short to ground	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 RH Side Crash Sensor circuit - short to ground	Refer to the electrical circuit diagrams and test RH Side Crash Sensor (B Pillar) circuit for short to ground
B0097-12	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right Side Restraints Sensor 2 - circuit short to battery	RH Side Crash Sensor circuit - short to power	Refer to the electrical circuit diagrams and test RH Side Crash Sensor (B Pillar) circuit for short to power
B0097-64	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right Side Restraints Sensor 2 - signal plausibility failure	RH Side Crash Sensor Signal plausibility failure	Configuration error- This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0097-81	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Right Side Restraints Sensor 2 - invalid serial data received	RH Side Crash Sensor circuit - open circuit Sensor fault	Refer to the electrical circuit diagrams and test RH Side Crash Sensor circuit for open circuit fault. Install a new sensor as necessary
B0097-92	Right Side Restraints Sensor 2 - performance or incorrect operation	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Performance or incorrect operation	Suspect RH Side Crash Sensor (B Pillar) internal fault
B0097-96	Right Side Restraints Sensor 2 - component internal failure	NOTE: Circuit reference RH SIDE SENS F1 / RH SIDE SENS R1 Component internal failure	Suspect RH Side Crash Sensor (B Pillar) internal fault
B0098-11	Right Side Restraints Sensor 3 - circuit short to ground	NOTE: Circuit reference RH SIDE SENS F2 / RH SIDE SENS R2 Right hand Rear Side Crash Sensor 3 circuit short to ground	Refer to the electrical circuit diagrams and check right hand Rear Side Crash Sensor circuit for short to ground
B0098-12	Right Side Restraints Sensor 3 - circuit short to battery	NOTE: Circuit reference RH SIDE SENS F2 / RH SIDE SENS R2 Right hand Rear Side Crash Sensor 3 circuit short to power	Refer to the electrical circuit diagrams and check right hand Rear Side Crash Sensor circuit for short to power
B0098-64	Right Side Restraints Sensor 3 - signal plausibility failure	NOTE: Circuit reference RH SIDE SENS F2 / RH SIDE SENS R2 Right hand Rear Side Crash Sensor 3 configuration error	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B0098-81	Right Side Restraints Sensor 3 - invalid serial data received	NOTE: Circuit reference RH SIDE SENS F2 / RH SIDE SENS R2 Right hand Rear Side Crash Sensor 3 circuit open circuit Right Side Restraints Sensor 3 failure	Refer to the electrical circuit diagrams and check right hand Rear Side Crash Sensor circuit for open circuit fault. Check and install a new Right Side Restraints Sensor 3 as required. Refer to the warranty policy and procedures manual if a module is suspect
B0098-92	Right Side Restraints Sensor 3 - performance or incorrect operation	NOTE: Circuit reference RH SIDE SENS F2 / RH SIDE SENS R2 Right Side Restraints Sensor 3 component internal failure	Check and install a new Right Side Restraints Sensor 3 as required. Refer to the warranty policy and procedures manual if a module is suspect
B0098-96	Right Side Restraints Sensor 3 - component internal failure	NOTE: Circuit reference RH SIDE SENS F2 / RH SIDE SENS R2 Right hand Rear Side Restraints Sensor 3 internal failure	Suspect right hand Rear Side Crash Sensor internal fault. Check and install a new Right Rear Side Restraints Sensor 3 as required. Refer to the warranty policy and procedures manual if a module is suspect
B00A0-49	Occupant Classification System - internal electronic failure	Occupant classification system module internal fault	Check Occupant classification system module for stored DTCs
B00A0-64	Occupant Classification System - signal plausibility failure	Signal plausibility failure	For Federal specification vehicles: Configuration error - This input has been switched off but the sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system. For non-Federal specification vehicles: This input has been switched off and the sensor is not installed. 1) This fault may be caused by an extended engine crank. Check for symptoms of poor engine starting or depleted battery charge levels. 2) Check the stowed unused safety belt tension sensor connector located on the passenger side rear heel board for any water ingress/dampness. Dry out, clean and prevent any further water ingress
B00A0-88	Occupant Classification System - bus off	CAN Bus Circuit Fault	Refer to the electrical circuit diagrams and check, CAN Bus circuit to Occupant classification system module for fault
B00A0-92	Occupant Classification System - performance or incorrect operation	Occupant classification system module internal fault	Check Occupant classification system module for stored DTCs
B00B5-11	Driver Seat Track Position Restraints Sensor - circuit short to ground	NOTE: Circuit reference DR SEAT TRACK POS F Driver seat position sensor circuit - short to ground	Refer to the electrical circuit diagrams and test Driver Seat Position Sensor circuit for short to ground
B00B5-15	Driver Seat Track Position Restraints Sensor - circuit short to battery or open	NOTE: Circuit reference DR SEAT TRACK POS F Driver seat position sensor circuit - short to power or open circuit	Refer to the electrical circuit diagrams and test Driver Seat Position Sensor circuit for short to power or open circuit
B00B5-1D	Driver Seat Track Position Restraints Sensor - circuit current out of range	NOTE: Circuit reference DR SEAT TRACK POS F Circuit current out of range	Refer to the electrical circuit diagrams and test Driver Seat Position Sensor circuit for fault
B00B5-64	Driver Seat Track Position Restraints Sensor - signal plausibility failure	NOTE: Circuit reference DR SEAT TRACK POS F Signal plausibility failure	Configuration error- This Input has been switched off but the Sensor is actually installed. Re-configure the Restraints control module using the manufacturer approved diagnostic system
B00C0-96	Passenger Seat Occupant Classification Sensor "A" - component internal failure	Occupant classification system module internal fault	Check Occupant classification system module for stored DTCs
B00D2-68	Restraint System Malfunction Indicator 1 - event information	Events information	Suspect Instrument Cluster Internal fault Check for stored DTCs
B00D2-87	Restraint System Malfunction Indicator 1 - missing message	Missing message from Instrument Cluster	Check CAN Bus circuit to Instrument Cluster for circuit fault
B00D5-14	Restraint System Passenger Disable Indicator - circuit short to ground or open	Passenger Airbag Disable (PAD) Lamp circuit short to ground or open	Refer to the electrical circuit diagrams and test PAD Lamp circuit for short to ground or open (PAD Lamp located on the Integrated Control Panel)
B00D5-55	Restraint System Passenger Disable Indicator - not configured	Module Not Configured	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B00DF-00	Passenger Restraints Disable Switch - no sub type information	Passenger Restraints Disable Switch stuck Passenger Restraints Disable Switch internal failure	Check and install a new Passenger Restraints Disable Switch as required. Refer to the warranty policy and procedures manual if a module is suspect
B00DF-54	Passenger Restraints Disable Switch - missing calibration	Passenger Restraints Disable Switch missing calibration	Using the manufacturer approved diagnostic system, calibrate the Passenger Restraints Disable Switch
B00DF-64	Passenger Restraints Disable Switch - signal plausibility failure	Passenger Restraints Disable Switch configuration error	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1211-11	Driver Seatbelt Retractor Pretensioner Deployment Control - circuit short to ground	Driver seatbelt retractor pretensioner deployment control circuit short to ground	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit short to ground
B1211-12	Driver Seatbelt Retractor Pretensioner Deployment Control - circuit short to battery	Driver seatbelt retractor pretensioner deployment control circuit short to power	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit short to power
B1211-1A	Driver Seatbelt Retractor Pretensioner Deployment Control - circuit resistance below threshold	Driver seatbelt retractor pretensioner deployment control circuit resistance below threshold	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit for circuit shorted to each other
B1211-1B	Driver Seatbelt Retractor Pretensioner Deployment Control - circuit resistance above threshold	Driver seatbelt retractor pretensioner deployment control circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit open circuit, high resistance
B1211-64	Driver Seatbelt Retractor Pretensioner Deployment Control - signal plausibility failure	Driver seatbelt retractor pretensioner deployment control configuration error	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1211-95	Driver Seatbelt Retractor Pretensioner Deployment Control - incorrect assembly	Driver seatbelt retractor pretensioner deployment control short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit for faults
B1212-11	Driver Seatbelt Buckle Pretensioner Deployment Control - circuit short to ground	NOTE: Circuit reference DR PRETEN F1 / DR PRETEN R1 Driver seatbelt buckle pretensioner deployment control circuit short to ground	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit short to ground
B1212-12	Driver Seatbelt Buckle Pretensioner Deployment Control - circuit short to battery	NOTE: Circuit reference DR PRETEN F1 / DR PRETEN R1 Driver seatbelt buckle pretensioner deployment control circuit short to power	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit short to power
B1212-1A	Driver Seatbelt Buckle Pretensioner Deployment Control - circuit resistance below threshold	NOTE: Circuit reference DR PRETEN F1 / DR PRETEN R1 Driver seatbelt buckle pretensioner deployment control circuit resistance below threshold	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit for circuit shorted to each other
B1212-1B	Driver Seatbelt Buckle Pretensioner Deployment Control - circuit resistance above threshold	NOTE: Circuit reference DR PRETEN F1 / DR PRETEN R1 Driver seatbelt buckle pretensioner deployment control circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit open circuit, high resistance
B1212-64	Driver Seatbelt Buckle Pretensioner Deployment Control - signal plausibility failure	NOTE: Circuit reference DR PRETEN F1 / DR PRETEN R1 Driver seatbelt retractor pretensioner deployment control configuration error	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1212-95	Driver Seatbelt Buckle Pretensioner Deployment Control - incorrect assembly	NOTE: Circuit reference DR PRETEN F1 / DR PRETEN R1 Driver seatbelt buckle pretensioner deployment control short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit for faults
B1213-11	Passenger Seatbelt Buckle Pretensioner Deployment Control - circuit short to ground	NOTE: Circuit reference PASS PRETEN F1 / PASS PRETEN R1 Passenger seatbelt buckle pretensioner deployment control circuit short to ground	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit short to ground
B1213-12	Passenger Seatbelt Buckle Pretensioner Deployment Control - circuit short to battery	NOTE: Circuit reference PASS PRETEN F1 / PASS PRETEN R1 Passenger seatbelt buckle pretensioner deployment control circuit short to power	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit short to power
B1213-1A	Passenger Seatbelt Buckle Pretensioner Deployment Control - circuit resistance below threshold	NOTE: Circuit reference PASS PRETEN F1 / PASS PRETEN R1 Passenger seatbelt buckle pretensioner deployment control circuit resistance below threshold	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit for circuit shorted to each other
B1213-1B	Passenger Seatbelt Buckle Pretensioner Deployment Control - circuit resistance above threshold	NOTE: Circuit reference PASS PRETEN F1 / PASS PRETEN R1 Passenger seatbelt buckle pretensioner deployment control circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit open circuit, high resistance
B1213-64	Passenger Seatbelt Buckle Pretensioner Deployment Control - signal plausibility failure	NOTE: Circuit reference PASS PRETEN F1 / PASS PRETEN R1 Passenger seatbelt retractor pretensioner deployment control configuration error	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1213-95	Passenger Seatbelt Buckle Pretensioner Deployment Control - incorrect assembly	NOTE: Circuit reference PASS PRETEN F1 / PASS PRETEN R1 Passenger seatbelt buckle pretensioner deployment control short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit for faults
B1A00-16	Control Module - circuit voltage below threshold	System voltage low at ECU (supply voltage less than 9 volts)	Refer to the electrical circuit diagrams and check, power and ground circuit for fault
B1A00-17	Control Module - circuit voltage above threshold	System voltage high (supply voltage supply greater than 16 volts)	Check Engine control module for stored DTCs, Suspect charging system fault. Refer to the electrical circuit diagrams and check, power and ground circuit for fault
B1A00-49	Control Module - internal electronic failure	Restraints control module internal electronic failure	Suspect Restraints control module internal fault. Check and install a new Restraints control module as required. Refer to the warranty policy and procedures manual if a module is suspect
B1A17-95	Driver Stage 1 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference DR AIRBAG F1 / DR AIRBAG R1 Driver airbag (stage 1) incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check left hand side Air Bag circuit for faults
B1A19-95	Driver Stage 2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference DR AIRBAG F2 / DR AIRBAG R2 Driver airbag (stage 2) incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check right hand side curtain Air Bag (row 1&2) circuit for faults
B1A21-95	Passenger Stage 1 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference PASS AIRBAG F1 / PASS AIRBAG R1 Passenger airbag (stage 1) incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check left hand side curtain Air Bag (row 1&2) circuit for faults
B1A23-95	Passenger Stage 2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Circuit reference PASS AIRBAG F2 / PASS AIRBAG R2 Passenger airbag (stage 2) incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Passenger Air bag circuit for faults
B1A29-95	Left Side Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference LH SIDE A/BAG F1 / LH SIDE A/BAG R1 Left Side Airbag Squib short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check left hand side Air Bag circuit for faults
B1A31-95	Right Side Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference RH SIDE A/BAG F1 / RH SIDE A/BAG R1 Right side airbag incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check right hand side Air Bag circuit for faults
B1A33-95	Left Curtain Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference LH SIDE CUR F1 / LH SIDE CUR R1 Left side air curtain incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check left hand side curtain Air Bag circuit for faults
B1A35-95	Right Curtain Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	NOTE: Circuit reference RH SIDE CUR F1 / RH SIDE CUR R1 Right side air curtain incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check right hand side curtain Air Bag circuit for faults
B1A37-95	Left Curtain #2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Left Curtain #2 Airbag Squib short circuit between two different circuits (at least two faults)	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and check left hand side curtain Air Bag (row 3) circuit for faults
B1A39-95	Right Curtain #2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Right Curtain #2 Airbag Squib short circuit between two different circuits (at least two faults)	NOTE: Applicable to seven seat vehicles. Refer to electrical circuit diagrams and check right hand side curtain Air Bag (row 3) circuit for faults
B1A40-11	Left Side (pelvic) 2 - circuit short to ground	Only logged in the event of incorrect module configuration. Not used for 10MY	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A40-12	Left Side (pelvic) 2 - circuit short to battery	Only logged in the event of incorrect module configuration. Not used for 10MY	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A40-1A	Left Side (pelvic) 2 - circuit resistance below threshold	Only logged in the event of incorrect module configuration. Not used for 10MY	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A40-1B	Left Side (pelvic) 2 - circuit resistance above threshold	Only logged in the event of incorrect module configuration. Not used for 10MY	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A40-64	Left Side (pelvic) 2 - signal plausibility failure	Only logged in the event of incorrect module configuration. Not used for 10MY	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A40-95	Left Side (pelvic) 2 - incorrect assembly	Only logged in the event of incorrect module configuration. Not used for 10MY	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A41-95	Left Side (pelvic) 2 Short circuit To Ignition Loop - incorrect assembly	Left Side (pelvic) 2 incorrect assembly. Short circuit between two different circuits (at least two faults)	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1A55-14	Crash Record Output - circuit short to ground or open	NOTE: Circuit reference CRASH OUTPUT Crash Record Output circuit short to ground or open	Refer to the electrical circuit diagrams and test Crash Record Output circuit for short to ground or open circuit. If this has occurred after a software download then disconnect the battery for 1 minute
B1A55-64	Crash Record Output - signal plausibility failure	NOTE: Circuit reference CRASH OUTPUT Signal plausibility failure	Re-configure the Restraints control module using the manufacturer approved diagnostic system
B1D74-11	Passenger Airbag Cutoff Enable Switch - circuit short to ground	Passenger Airbag Enable Switch circuit short circuit to ground	Refer to the electrical circuit diagrams and check Passenger Airbag Enable Switch circuit for short circuit to ground
B1D74-12	Passenger Airbag Cutoff Enable Switch - circuit short to battery	Passenger Airbag Enable Switch circuit short circuit to power	Refer to the electrical circuit diagrams and check Passenger Airbag Enable Switch circuit for short circuit to power
B1D74-13	Passenger Airbag Cutoff Enable Switch - circuit open	Passenger Airbag Enable Switch circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check Passenger Airbag Enable Switch circuit for open circuit, high resistance
B1D75-11	Passenger Airbag Cutoff Disable Switch - circuit short to ground	Passenger Airbag Disable Switch circuit short circuit to ground	Refer to the electrical circuit diagrams and check Passenger Airbag Disable Switch circuit for short circuit to ground
B1D75-12	Passenger Airbag Cutoff Disable Switch - circuit short to battery	Passenger Airbag Disable Switch circuit short circuit to power	Refer to the electrical circuit diagrams and check Passenger Airbag Disable Switch circuit for short circuit to power
B1D75-13	Passenger Airbag Cutoff Disable Switch - circuit open	Passenger Airbag Disable Switch open circuit, high resistance	Refer to the electrical circuit diagrams and check Passenger Airbag Disable Switch circuit for open circuit, high resistance
U0001-88	High Speed CAN Communication Bus - bus off	CAN Bus Circuit fault	Refer to the electrical circuit diagrams and check, CAN Bus circuit for fault
U0122-87	Lost Communication With Vehicle Dynamics Control Module - missing message	Lost Communication With Vehicle Dynamics Control Module	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Restraints control module and Vehicle Dynamics Control Module
U0300-55	Internal Control Module Software Incompatibility - not configured	Mis-match between vehicle and Restraints control module software levels	Re-configure the Restraints control module with the latest level software using the manufacturer approved diagnostic system
U1A02-66	Permanent Memory Store Full - signal has too many transitions / events	Wiring harness fault Restraint Control Module internal fault	Restraint Control Module memory full - refer to the new module installation note at the top of the DTC index (Not warrantable change)
U1A03-87	Car Configuration Parameter - missing message	Missing message	Lost communication with Body control module. Check Body control module for stored DTCs. Refer to the electrical circuit diagrams and check, CAN Bus circuit to Body Control Module for fault
U1A14-55	CAN Initialization Failure - not configured	Not configured	Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U201A-4A	Control Module Main Calibration Data - incorrect component installed	Incorrect component installed	Re-configure the Restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U201A-51	Control Module Main Calibration Data - not programmed	Not programmed	Re-configure the Restraints control module with the latest level software using the manufacturer approved diagnostic system
U201B-4A	Control Module Calibration Data #2 - incorrect component installed	Incorrect component installed	Re-configure the Restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U201B-51	Control Module Calibration Data #2 - not programmed	Not programmed	Re-configure the Restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U201C-4A	Control Module Calibration Data #3 - incorrect component installed	Incorrect component installed	Re-configure the Restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U201C-51	Control Module Calibration Data #3 - not programmed	Not programmed	Re-configure the Restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U3000-49	Control Module - internal electronic failure	Internal electronic failure	Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect
U3002-81	Vehicle Identification Number - invalid serial data received	Vehicle/component mis-match. Corrupt VIN data being transmitted, module previously installed to other vehicle	Re-configure the Restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Suspect Restraints control module internal fault. Refer to the warranty policy and procedures manual if a module is suspect