LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2013 >> LR4 Base >> Repair and Diagnosis (Single Page) >> General Information >> DTC Index >> DTC Index & General Information (2 Of 3) >> Description & Operation >> Diagnostic Trouble Code (DTC) Index - (V8 5.0L Petrol, DTC: Engine Control Module (Pcm)) >> Engine Control Module (Pcm) 5.0L V8 >> DTC's

Engine Control Module (Pcm) 5.0L V8: DTC's

DTC Description Possible Causes Action
B10A2-31 Crash Input - No signal
NOTE: - Circuit SRS_SIGNAL -
  • Loss of communication between restraints control module and engine control module
  • Refer to the electrical circuit diagrams and check restraints control module pulse width modulated SRS signal line circuit, hard wired connection between engine control module and restraints control module for short circuit to ground, short circuit to power, open circuit. Repair circuit as required, clear the DTC and retest
B10AC-81 Cruise Control Switch - Invalid serial data received
  • The engine control module has received an invalid command from the steering wheel switch pack
  • Clear the DTC and press all the steering wheel switches, re-check for DTCs. Refer to the electrical circuit diagrams and check the speed control switch circuit for open circuit, short circuit to power, short circuit to ground, disconnected
  • Check and install a new steering wheel module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B10AC-82 Cruise Control Switch - Alive / sequence counter incorrect / not updated
  • Cruise buttons alive counter is not incrementing. Which suggests that the LIN bus is faulty
  • Steering wheel module is not connected
  • Steering wheel module failure
  • Refer to the electrical circuit diagrams and check the speed control switch circuit for open circuit, short circuit to power, short circuit to ground, disconnected
  • Refer to the electrical circuit diagrams and check the LIN bus between steering wheel module and the CAN gateway
  • Check and install a new steering wheel module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B10AC-83 Cruise Control Switch - Value of signal protection calculation incorrect
  • Cruise buttons checksum incorrect, incorrect cruise switches fitted to vehicle
  • Check and install new cruise switches as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B10AC-96 Cruise Control Switch - Component internal failure
  • Speed control switch circuit, open circuit, short circuit to power, short circuit to ground, disconnected
  • Speed control switch failure
  • Steering wheel module failure
  • Check for related DTCs in other central junction boxes
  • Refer to the electrical circuit diagrams and check the speed control switch circuit for open circuit, short circuit to power, short circuit to ground, disconnected
  • Check and install a new speed control switch as required. Check and install a new steering wheel module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B10FF-68 Ignition Control - Event information
  • Spark plug(s) fault
  • Wiring harness fault
  • Ignition coil(s) fault
  • Refer to repair manual and check spark plug(s) for condition and security. Replace any defective components as required
  • Refer to electrical wiring diagrams and check ignition coil circuit for intermittent open circuit, short circuit to power, short circuit to ground
  • Check and install a new coil(s) as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B11DB-01 Battery Monitoring Module - General electrical failure
NOTE: - Circuit BATTERY -
  • Charging system fault
  • Battery monitoring signal line circuit fault
  • Vehicle battery fault
  • Refer to electrical wiring diagrams and check charging system for faults. Perform any repairs required
  • Refer to the electrical wiring diagrams and check the battery monitoring system module circuit for open circuit, short circuit to ground, short circuit to power
  • Refer to the workshop manual and the battery care manual, inspect the vehicle battery and ensure it is fully charged and serviceable before performing further tests
B11DB-87 Battery Monitoring Module - Missing message
NOTE: - Circuit BATTERY -
  • Battery signal line circuit fault
  • Refer to the electrical wiring diagrams and check the battery monitoring system module circuit for open circuit, short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check the LIN circuit for short circuit to ground, short circuit to power, open circuit
B1206-68 Crash Occurred - Event information
NOTE: - Circuit SRS_SIGNAL -
  • Engine control module has detected the vehicle has crashed - event information DTC only
  • Refer to the electrical circuit diagrams and check the engine control module to restraints control module circuit for short circuit to ground, short circuit to power, open circuit. Repair circuit as required, clear the DTC and retest
C0031-00 Left Front Wheel Speed Sensor - No sub type information
  • Invalid data received from anti-lock braking system module - left front wheel speed signal fault
  • Check anti-lock braking system module for related DTCs and refer to relevant DTC index
C0034-00 Right Front Wheel Speed Sensor - No sub type information
  • Invalid data received from anti-lock braking system module - right front wheel speed signal fault
  • Check anti-lock braking system module for related DTCs and refer to relevant DTC index
C0037-00 Left Rear Wheel Speed Sensor - No sub type information
  • Invalid data received from anti-lock braking system module - left rear wheel speed signal fault
  • Check anti-lock braking system module for related DTCs and refer to relevant DTC index
C003A-00 Right Rear Wheel Speed Sensor - No sub type information
  • Invalid data received from anti-lock braking system module - right rear wheel speed signal fault
  • Check anti-lock braking system module for related DTCs and refer to relevant DTC index
P0010-13 Intake (A) Camshaft Position Actuator (Bank 1) - Circuit open
NOTE: - Circuit VFS_IN_A -
  • Intake (A) camshaft position actuator (Bank 1) open circuit
  • Engine control module interface harness open circuit
  • Refer to the electrical circuit diagrams and check intake (A) camshaft position actuator (Bank 1) circuit for open circuit
  • Refer to the electrical circuit diagrams and check engine control module interface harness for open circuit
P0011-00 Intake (A) Camshaft Position Timing - Over-Advanced (Bank 1) - No sub type information
NOTE: - Circuit VFS_IN_A -
  • Intake (A) camshaft position actuator (Bank 1) open circuit
  • Engine control module interface harness open circuit
  • Refer to the electrical circuit diagrams and check intake (A) camshaft position actuator (Bank 1) circuit for open circuit
  • Refer to the electrical circuit diagrams and check engine control module interface harness for open circuit
P0013-13 Exhaust (B) Camshaft Position Actuator (Bank 1) - Circuit open
NOTE: - Circuit VFS_EX_A -
  • Exhaust (B) camshaft position actuator (Bank 1) open circuit
  • Engine control module interface harness open circuit
  • Refer to the electrical circuit diagrams and check exhaust (B) camshaft position actuator (Bank 1) circuit for open circuit
  • Refer to the electrical circuit diagrams and check engine control module interface harness for open circuit
P0015-00 Exhaust (B) Camshaft Position Timing - Over-Retarded (Bank 1) - No sub type information
NOTE: - Circuit VFS_EX_A -
  • Exhaust (B) camshaft position actuator (Bank 1) open circuit, short circuit to ground, short circuit to power
  • Check for related DTC P0365-00. Refer to the electrical circuit diagrams and check exhaust (B) camshaft position actuator (Bank 1) for open circuit, short circuit to ground, short circuit to power
P0016-00 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A - No sub type information
NOTE: - Circuit VFS_EX_A -
  • The relative positions of the crankshaft position sensor and cam timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
  • Variable valve timing forced fully advanced
  • Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly
P0017-00 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B - No sub type information
NOTE: - Circuit VFS_EX_A -
  • The relative positions of the crankshaft position sensor and camshaft timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
  • Variable valve timing forced fully advanced
  • Check for related DTC P0365-00. Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly
  • Refer to the electrical circuit diagrams and check exhaust (B) camshaft position actuator (Bank 1) for open circuit, short circuit to ground, short circuit to power
P0018-00 Crankshaft Position - Camshaft Position Correlation - Bank 2 Sensor A - No sub type information
NOTE: - Circuit VFS_IN_B -
  • The relative positions of the crankshaft position sensor and camshaft timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
  • Variable valve timing forced fully advanced
  • Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly
P0019-00 Crankshaft Position - Camshaft Position Correlation - Bank 2 Sensor B - No sub type information
NOTE: - Circuit VFS_EX_B -
  • The relative positions of the crankshaft position sensor and camshaft timing plate teeth are not correct
  • Engine timing incorrect
  • Timing chain installed incorrectly
  • Variable valve timing forced fully advanced
  • Check engine timing. Check camshaft sensor timing plate is installed correctly. Check timing chain is installed correctly
P001A-13 Intake (A) Cam Profile Control Circuit (Bank 1) - Circuit open
NOTE: - Circuit CPS_A -
  • Camshaft profile switching solenoid bank 1 open circuit
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 for open circuit
P001B-11 Intake (A) Cam Profile Control Circuit Low (Bank 1) - Circuit short to ground
NOTE: - Circuit CPS_A -
  • Camshaft profile switching solenoid bank 1 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 circuit for short circuit to ground
P001C-12 Intake (A) Cam Profile Control Circuit High (Bank 1) - Circuit short to battery
NOTE: - Circuit CPS_A -
  • Camshaft profile switching solenoid bank 1 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 circuit for short circuit to power
P001D-13 Intake (A) Cam Profile Control Circuit (Bank 2) - Circuit open
NOTE: - Circuit CPS_B -
  • Camshaft profile switching solenoid bank 2 open circuit
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 for open circuit
P001E-11 Intake (A) Cam Profile Control Circuit Low (Bank 2) - Circuit short to ground
NOTE: - Circuit CPS_B -
  • Camshaft profile switching solenoid bank 2 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 circuit for short circuit to ground
P001F-12 Intake (A) Cam Profile Control Circuit High (Bank 2) - Circuit short to battery
NOTE: - Circuit CPS_B -
  • Camshaft profile switching solenoid bank 2 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 circuit for short circuit to power
P0020-13 Intake (A) Camshaft Position Actuator (Bank 2) - Circuit open
NOTE: - Circuit VFS_IN_B -
  • Intake valve solenoid 2 open circuit
  • Refer to the electrical circuit diagrams and check intake valve solenoid 2 for open circuit
P0023-13 Exhaust (B) Camshaft Position Actuator (Bank 2) - Circuit open
NOTE: - Circuit VFS_EX_B -
  • Exhaust (B) Camshaft Position actuator (Bank 2) circuit, open circuit
  • Refer to the electrical circuit diagrams and check exhaust (B) camshaft position actuator (Bank 2) circuit for open circuit
P0026-72 Intake Valve Control Solenoid Circuit Range/Performance (Bank 1) - Actuator stuck open
NOTE: - Circuit VFS_IN_A -
  • Intake valve solenoid 1 angle less than target
  • Intake valve solenoid 1 slow or not operating
  • Check operation of intake valve solenoid 1. Check and install a new intake valve solenoid 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0026-77 Intake Valve Control Solenoid Circuit Range/Performance (Bank 1) - Commanded position not reachable
NOTE: - Circuit VFS_IN_A -
  • Intake valve solenoid 1 angle greater than target
  • Intake valve solenoid 1 not returning to target in time
  • Intake valve solenoid 1 stuck advanced
  • Check operation of intake valve solenoid 1. Check and install a new intake valve solenoid 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0027-72 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 1) - Actuator stuck open
NOTE: - Circuit VFS_EX_A -
  • Exhaust valve solenoid 1 angle less than target
  • Exhaust valve solenoid 1 slow or not operating
  • Check operation of exhaust valve solenoid 1. Check and install a new exhaust valve solenoid 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0027-77 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 1) - Commanded position not reachable
NOTE: - Circuit VFS_EX_A -
  • Exhaust valve solenoid 1 angle greater than target
  • Exhaust valve solenoid 1 not returning to target in time
  • Exhaust valve solenoid 1 stuck advanced
  • Check operation of exhaust valve solenoid 1. Check and install a new exhaust valve solenoid 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0028-72 Intake Valve Control Solenoid Circuit Range/Performance (Bank 2) - Actuator stuck open
NOTE: - Circuit VFS_IN_B -
  • Intake valve solenoid 2 angle less than target
  • Intake valve solenoid 2 slow or not operating
  • Check operation of intake valve solenoid 2. Check and install a new intake valve solenoid 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0028-77 Intake Valve Control Solenoid Circuit Range/Performance (Bank 2) - Commanded position not reachable
NOTE: - Circuit VFS_IN_B -
  • Intake valve solenoid 2 angle greater than target
  • Intake valve solenoid 2 not returning to target in time
  • Intake valve solenoid 2 stuck advanced
  • Check operation of intake valve solenoid 2. Check and install a new intake valve solenoid 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0029-72 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 2) - Actuator stuck open
NOTE: - Circuit VFS_EX_B -
  • Exhaust valve solenoid 2 angle less than target
  • Exhaust valve solenoid 2 slow or not operating
  • Check operation of exhaust valve solenoid 2. Check and install a new exhaust valve solenoid 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0029-77 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 2) - Commanded position not reachable
NOTE: - Circuit VFS_EX_B -
  • Exhaust valve solenoid 2 angle greater than target
  • Exhaust valve solenoid 2 not returning to target in time
  • Exhaust valve solenoid 2 stuck advanced
  • Check operation of exhaust valve solenoid 2. Check and install a new exhaust valve solenoid 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0031-11 HO2S Heater Control Circuit Low (Bank 1, Sensor 1) - Circuit short to ground
NOTE: - Circuit HTR_CTRL_A_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER A -
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit short circuit to ground
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1)
  • Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit for short circuit to ground
P0031-13 HO2S Heater Control Circuit Low (Bank 1, Sensor 1) - Circuit open
NOTE: - Circuit HTR_CTRL_A_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER A -
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit, open circuit
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1)
  • Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit for open circuit
P0032-12 HO2S Heater Control Circuit High (Bank 1, Sensor 1) - Circuit short to battery
NOTE: - Circuit HTR_CTRL_A_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER A -
  • Pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit short circuit to power
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1)
  • Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-odd heater control circuit (Bank 1, Sensor 1) circuit for short circuit to power
P0036-00 HO2S Heater Control Circuit (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HTR_HEGO_A -
  • Catalyst oxygen sensor heater circuit control fuse failure
  • Post catalyst oxygen sensor-odd heater control circuit short circuit to ground, short circuit to power, open circuit
  • Catalyst oxygen sensor heater circuit control relay circuit short circuit to ground, short circuit to power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-odd failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 2 (0x03A2)
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor fuse for open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P003C-00 A Camshaft Profile Control Performance /Stuck Off (Bank 1) - No sub type information
NOTE: - Circuit CPS_A -
  • Oil supply blockage to camshaft profile switching solenoid
  • Catalyst oxygen sensor failure, giving false flag
  • Camshaft profile switching solenoid bank 1 circuit fault
  • Camshaft profile switching solenoid bank 1 fault
  • Check for the presence of oil at the camshaft profile switching solenoid
  • Check for catalyst oxygen sensor related DTCs
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 1 circuit for short circuit to power, short circuit to ground, open circuit
  • Check and install a new camshaft profile switching solenoid bank 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
  • Clear DTC and road test the vehicle. If fault remains contact dealer technical support before carrying out any further work
P003E-00 A Camshaft Profile Control Performance/ Stuck Off (Bank 2) - No sub type information
NOTE: - Circuit CPS_B -
  • Oil supply blockage to camshaft profile switching solenoid
  • Catalyst oxygen sensor failure, giving false flag
  • Camshaft profile switching solenoid bank 2 circuit fault
  • Camshaft profile switching solenoid bank 2 fault
  • Check for the presence of oil at the camshaft profile switching solenoid
  • Check for catalyst oxygen sensor related DTCs
  • Refer to the electrical circuit diagrams and check camshaft profile switching solenoid bank 2 circuit for short circuit to power, short circuit to ground, open circuit
  • Check and install a new camshaft profile switching solenoid bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
  • Clear DTC and road test the vehicle. If fault remains contact dealer technical support before carrying out any further work
P0051-11 HO2S Heater Control Circuit Low (Bank 2, Sensor 1) - Circuit short to ground
NOTE: - Circuit HTR_CTRL_B_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER B -
  • Pre catalyst oxygen sensor-even heater control circuit (Bank 2, Sensor 1) circuit short circuit to ground
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 1 (0x03A4)
  • Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-even heater control circuit (Bank 2, Sensor 1) circuit for short circuit to ground
P0051-13 HO2S Heater Control Circuit Low (Bank 2, Sensor 1) - Circuit open
NOTE: - Circuit HTR_CTRL_B_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER B -
  • Pre catalyst oxygen sensor-even heater control circuit (Bank 2, Sensor 1) circuit, open circuit
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 1 (0x03A4)
  • Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-even heater control circuit (Bank 2, Sensor 1) circuit for open circuit
P0052-12 HO2S Heater Control Circuit High (Bank 2, Sensor 1) - Circuit short to battery
NOTE: - Circuit HTR_CTRL_B_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER B -
  • Pre catalyst oxygen sensor-even heater control circuit (Bank 2, Sensor 1) circuit short circuit to power
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 1 (0x03A4)
  • Refer to the electrical circuit diagrams and check pre catalyst oxygen sensor-even heater control circuit (Bank 2, Sensor 1) circuit for short circuit to power
P0054-00 HO2S Heater Resistance (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HTR_CTRL_A_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER A -
  • Catalyst oxygen sensor heater circuit control fuse failure
  • Post catalyst oxygen sensor-odd heater control circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Catalyst oxygen sensor heater circuit control relay circuit short circuit to ground, short circuit to power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-odd failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 1 (0x03A1)
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor fuse for open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-odd sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0056-00 HO2S Heater Control Circuit (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HTR_HEGO_B -
  • Post catalyst oxygen sensor-even heater control circuit short circuit to ground, short circuit to power, open circuit
  • Catalyst oxygen sensor heater circuit control relay circuit short circuit to ground, short circuit to power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-even failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 2 (0x03A5)
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-even sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0060-00 HO2S Heater Resistance (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HTR_CTRL_B_UPSTREAM -
NOTE: LR - Circuit UHEGO HEATER B -
  • Catalyst oxygen sensor heater circuit control fuse failure
  • Post catalyst oxygen sensor-even heater control circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Catalyst oxygen sensor heater circuit control relay circuit short circuit to ground, short circuit to power, open circuit
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor-even failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 2 Sensor 2 (0x03A5)
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-even sensor fuse for open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor-even sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install a new post catalyst oxygen sensor-even as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0069-29 MAP - Barometric Pressure Correlation - Signal invalid
  • Manifold absolute pressure sensor failure
  • Engine control module failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Barometric Pressure Sensor Voltage (0x035A). Check for related manifold absolute pressure sensor DTCs
  • Refer to the electrical circuit diagrams and check manifold absolute pressure sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install new manifold absolute pressure sensor as required. Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0071-21 Ambient Air Temperature Sensor Range/Performance - Signal amplitude < minimum
NOTE: Jaguar - Circuit AMBIENT_TEMP_SENSOR -
NOTE: LR - Circuit TAMB TEMP -
  • Ambient air temperature sensor circuit short circuit to ground, short circuit to power, open circuit
  • Temperature and manifold absolute pressure sensor circuit short circuit to ground, short circuit to power, open circuit
  • Ambient air temperature sensor failure
  • Temperature and manifold absolute pressure sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Ambient Air Temperature Sensor Voltage (0x03BA)
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check temperature and manifold absolute pressure sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new ambient air temperature sensor as required. Check and install a new temperature and manifold absolute pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0071-22 Ambient Air Temperature Sensor Range/Performance - Signal amplitude > maximum
NOTE: - Circuit AMBIENT_TEMP_SENSOR -
NOTE: LR - Circuit TAMB TEMP -
  • Ambient air temperature sensor circuit short circuit to ground, short circuit to power, open circuit
  • Temperature and manifold absolute pressure sensor circuit short circuit to ground, short circuit to power, open circuit
  • Ambient air temperature sensor failure
  • Temperature and manifold absolute pressure sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Ambient Air Temperature Sensor Voltage (0x03BA)
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check temperature and manifold absolute pressure sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new ambient air temperature sensor as required. Check and install a new temperature and manifold absolute pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0072-00 Ambient Air Temperature Sensor Circuit Low - No sub type information
NOTE: - Circuit AMBIENT_TEMP_SENSOR -
NOTE: LR - Circuit TAMB TEMP -
  • Ambient air temperature sensor circuit short circuit to ground, open circuit, high resistance
  • Ambient air temperature sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Ambient Air Temperature Sensor Voltage (0x03BA)
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new ambient air temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0073-00 Ambient Air Temperature Sensor Circuit High - No sub type information
NOTE: - Circuit AMBIENT_TEMP_SENSOR -
NOTE: LR - Circuit TAMB TEMP -
  • Ambient air temperature sensor ground circuit high resistance, open circuit
  • Ambient air temperature sensor signal circuit short circuit to power
  • Ambient air temperature sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signals Ambient Air Temperature Sensor Voltage (0x03BA)
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, high resistance, short circuit to power. Check connector terminals for corrosion or damage
  • Check and install a new ambient air temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P007B-23 Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1) - Signal stuck low
NOTE: - Circuit TMAP_TEMP_SENSOR -
  • Charge air cooler temperature sensor circuit poor / intermittent connection
  • Charge air cooler temperature sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Charge Air Temperature Voltage (0x03EE)
  • Refer to the electrical circuit diagrams and check charge air cooler temperature sensor circuit for poor, intermittent connection
  • Check and install a new charge air cooler temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P007B-24 Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1) - Signal stuck high
NOTE: - Circuit TMAP_TEMP_SENSOR -
  • Charge air cooler temperature sensor circuit short circuit to ground, open circuit
  • Charge air cooler temperature sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Charge Air Temperature Voltage (0x03EE)
  • Refer to the electrical circuit diagrams and check charge air cooler temperature sensor circuit for short circuit to ground, open circuit
  • Check and install a new charge air cooler temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P007B-29 Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1) - Signal invalid
NOTE: - Circuit TMAP_TEMP_SENSOR -
  • Charge air cooler temperature sensor circuit short circuit to ground, open circuit, short circuit to power
  • Charge air cooler temperature sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Charge Air Temperature Voltage (0x03EE)
  • Refer to the electrical circuit diagrams and check charge air cooler temperature sensor circuit for short circuit to ground, open circuit, short circuit to power
  • Check and install a new charge air cooler temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0087-00 Fuel Rail/System Pressure - Too Low - No sub type information
NOTE: - Circuit FUEL_HIGH_PRESS_SENSOR -
  • Fuel rail pressure sensor circuit short circuit to ground, open circuit, high resistance
  • Fuel rail pressure sensor failure
  • Fuel lines leaking or restricted
  • Fuel pump failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377)
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short circuit to ground, open circuit, high resistance
  • Check for fuel pump related DTCs. Check fuel lines for leakage or restriction
  • Check and install new fuel rail pressure sensor as required. Check and install a new fuel pump as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0088-00 Fuel Rail/System Pressure - Too High - No sub type information
NOTE: - Circuit FUEL_HIGH_PRESS_SENSOR -
  • Fuel rail pressure sensor circuit short to each other, high resistance, short circuit to power
  • Fuel rail pressure sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377)
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short to each other, high resistance, short circuit to power
  • Check and install new fuel rail pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P008A-00 Low Pressure Fuel System Pressure - Too Low - No sub type information
NOTE: - Circuit LOW_PRESS_FUEL_PRESS_SENSOR -
  • Low pressure fuel sensor circuit failure, short circuit to ground, short circuit to power, open circuit
  • Fuel pump driver module circuit short circuit to ground, short circuit to power, open circuit
  • Low pressure fuel
  • Fuel pump driver module failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376)
  • Check fuel system for leakage
  • Refer to the electrical circuit diagrams and check low pressure fuel sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check fuel pump driver module circuit short circuit to ground, short circuit to power, open circuit
  • Check and install a new low pressure fuel sensor as required. Check and install a new fuel pump driver module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P008B-00 Low Pressure Fuel System Pressure - Too High - No sub type information
NOTE: - Circuit LOW_PRESS_FUEL_PRESS_SENSOR -
  • Low pressure fuel sensor circuit short circuit to ground, short circuit to power, open circuit
  • Fuel pump driver module circuit short circuit to ground, short circuit to power, open circuit
  • Blockage or restriction in low pressure fuel line
  • Low pressure fuel sensor failure
  • Fuel pump driver module failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376)
  • Refer to the electrical circuit diagrams and check low pressure fuel sensor circuit for short circuit to ground, short circuit to power, open circuit. Check for blockage or restriction in low pressure fuel line
  • Refer to the electrical circuit diagrams and check fuel pump driver module circuit short circuit to ground, short circuit to power, open circuit
  • Check and install a new low pressure fuel sensor as required. Check and install a new fuel pump driver module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P00AB-23 Intake Air Temperature Sensor 1 Circuit Range/Performance (Bank 2) - Signal stuck low
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_B -
  • Intake air temperature sensor bank 2 circuit short circuit to ground, open circuit
  • Intake air temperature sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312)
  • Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short circuit to ground, open circuit
  • Check and install a new intake air temperature sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P00AB-24 Intake Air Temperature Sensor 1 Circuit Range/Performance (Bank 2) - Signal stuck high
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_B -
  • Intake air temperature sensor bank 2 circuit short circuit to power
  • Intake air temperature sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312)
  • Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short circuit to power
  • Check and install a new intake air temperature sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P00AB-29 Intake Air Temperature Sensor 1 Circuit Range/Performance (Bank 2) - Signal invalid
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_B -
  • Intake air temperature sensor bank 2 circuit short circuit to ground, open circuit, short circuit to power
  • Intake air temperature sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312)
  • Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for open circuit, short circuit to ground, short circuit to power
  • Check and install a new intake air temperature sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P00AC-00 Intake Air Temperature Sensor 1 Circuit Low (Bank 2) - No sub type information
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_B -
  • Intake air temperature sensor bank 2 sensing circuit short circuit to ground, high resistance, disconnected
  • Intake air temperature sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312)
  • Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short circuit to ground, open circuit, high resistance, disconnected connector
  • Check and install a new intake air temperature sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P00AD-00 Intake Air Temperature Sensor 1 Circuit High (Bank 2) - No sub type information
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_B -
  • Intake air temperature sensor bank 2 sensing circuit short ground, short circuit to power, open circuit, high resistance
  • Intake air temperature sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Intake Air Temperature Sensor Bank 2 (0x0312)
  • Refer to the electrical circuit diagrams and check intake air temperature sensor bank 2 circuit for short ground, short circuit to power, open circuit, high resistance. Check for backed out or damaged connector pins
  • Check and install a new intake air temperature sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P00C6-00 Fuel Rail Pressure Too Low - Engine Cranking - No sub type information
  • No fuel at pump
  • Injector stuck open
  • Fuel pressure sensor signal stuck
  • Fuel pump failure
  • Check fuel supply to both pumps (if engine runs then supply is not suspect). If engine does not run perform fuel prime routine. Use fuel pump diagnostic routine to determine if one pump has failed, if so replace pump. If a fuel injector is stuck open the exhaust will smell of fuel and fuelling adaptions may indicate rich shift. Perform checks for as DTC P0191-00
  • Check and install a new fuel pump as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0101-00 Mass or Volume Air Flow A Circuit Range/Performance - No sub type information
NOTE: - Circuit MAF_SENSOR_A -
NOTE: Customer likely to report hesitation
  • Blocked air cleaner element(s)
  • Leakage from air intake system
  • Blocked engine breather
  • Blockage in air intake system
  • Carbon build-up on throttle blade
  • Blocked catalysts
  • Blocked injectors
  • MAF/IAT sensor bank 1 circuit - high resistance, intermittent short circuit to ground, high resistance
  • MAF/IAT sensor bank 1 failure
  • Check air cleaner element is free from restriction
  • Check for leak from air intake system, rectify as required
  • Ensure the engine breather system is correctly installed and in serviceable condition
  • Make sure throttle blade is clean of carbon
  • Check for blocked catalysts
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor bank 1 sensor circuit for intermittent short circuit to ground, high resistance
  • Check for blocked injectors
  • Check and install a new MAF/IAT sensor bank 1 sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0102-00 Mass or Volume Air Flow A Circuit Low - No sub type information
NOTE: - Circuit MAF_SENSOR_A -
NOTE: Customer likely to report hesitation
  • Mass air flow sensor bank 1 circuit high resistance, open circuit
  • Mass air flow sensor bank 1 failure
  • Refer to the electrical circuit diagrams and check mass air flow sensor bank 1 circuit for high resistance, open circuit
  • Check and install a new mass air flow sensor bank 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0103-00 Mass or Volume Air Flow A Circuit High - No sub type information
NOTE: - Circuit MAF_SENSOR_A -
NOTE: Customer likely to report hesitation
  • Mass air flow sensor bank 1 circuit high resistance, open circuit, short circuit to ground, short circuit to power
  • Blocked air cleaner element(s)
  • Blockage in air intake system
  • Mass air flow sensor bank 1 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor, Bank 1 (0x0314)
  • Check mass air flow sensor circuit fuse. If fuse fails, may see DTCs P0103, P010C and P250C
  • Refer to the electrical circuit diagrams and check mass air flow sensor bank 1 circuit for short circuit to power, high resistance
  • Check air cleaner element is free from restriction
  • Check air intake system for blockage
  • Check and install a new mass air flow sensor bank 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0106-00 Manifold Absolute Pressure/BARO Sensor Range/Performance - No sub type information
NOTE: - Circuit MAP_SENSOR -
  • Blocked air cleaner element(s)
  • Intake manifold air leak
  • Manifold absolute pressure sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Engine breather leak
  • Carbon build up on throttle plate
  • Exhaust system blocked
  • Manifold absolute pressure sensor failure
  • BARO sensor failure
  • Check air cleaner element is free from restriction
  • Check for leak from air intake system, rectify as required
  • Refer to the electrical circuit diagrams and check manifold absolute pressure sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Ensure the engine breather system is correctly installed and in serviceable condition
  • Make sure throttle blade is clean of carbon
  • Check for blocked exhaust
  • Check and install a new manifold absolute pressure sensor as required. Check for related BARO sensor DTC P0069-29. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0107-00 Manifold Absolute Pressure/BARO Sensor Low - No sub type information
NOTE: - Circuit MAP_SENSOR -
  • Manifold absolute pressure sensor circuit short circuit to ground, open circuit, high resistance
  • Manifold absolute pressure sensor failure
  • Refer to the electrical circuit diagrams and check manifold absolute pressure sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new manifold absolute pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0108-00 Manifold Absolute Pressure/BARO Sensor High - No sub type information
NOTE: - Circuit MAP_SENSOR -
  • Manifold absolute pressure sensor circuit short circuit to power, open circuit, high resistance
  • Manifold absolute pressure sensor failure
  • Refer to the electrical circuit diagrams and check manifold absolute pressure sensor circuit for short circuit to power, open circuit, high resistance
  • Check and install a new manifold absolute pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P010B-00 Mass or Volume Air Flow B Circuit Range/Performance - No sub type information
NOTE: - Circuit MAF_SENSOR_B -
NOTE: Customer likely to report hesitation
  • Blocked air cleaner element(s)
  • Leakage from air intake system
  • Blocked engine breather
  • Blockage in air intake system
  • Carbon build-up on throttle blade
  • Blocked catalysts
  • Blocked injectors
  • MAF/IAT sensor bank 2 circuit - high resistance, intermittent short circuit to ground, high resistance
  • MAF/IAT sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503). Check for related DTCs P0102 or P0103
  • Check air cleaner element is free from restriction
  • Check for leak from air intake system, rectify as required
  • Ensure the engine breather system is correctly installed and in serviceable condition
  • Make sure throttle blade is clean of carbon
  • Check for blocked catalysts
  • Check for blocked injectors
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor bank 2 sensor circuit for intermittent short circuit to ground, high resistance
  • Check and install a new MAF/IAT sensor bank 2 sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P010C-00 Mass or Volume Air Flow B Circuit Low - No sub type information
NOTE: - Circuit MAF_SENSOR_B -
NOTE: Customer likely to report hesitation
  • Mass air flow sensor bank 2 circuit high resistance, open circuit, short circuit to ground, short circuit to power
  • Mass air flow sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503)
  • Check mass air flow sensor circuit fuse. If fuse fails, may see DTCs P0103, P010C and P250C
  • Refer to the electrical circuit diagrams and check mass air flow sensor bank 2 circuit for high resistance, open circuit, short circuit to ground, short circuit to power
  • Check and install a new mass air flow sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P010D-00 Mass or Volume Air Flow B Circuit High - No sub type information
NOTE: - Circuit MAF_SENSOR_B -
NOTE: Customer likely to report hesitation
  • Mass air flow sensor bank 2 circuit high resistance, open circuit, short circuit to ground, short circuit to power
  • Blocked air cleaner element(s)
  • Blockage in air intake system
  • Mass air flow sensor bank 2 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503)
  • Check mass air flow sensor circuit fuse. If fuse fails, may see DTCs P0103, P010C and P250C
  • Check air cleaner element is free from restriction
  • Check for blockage in air intake system
  • Refer to the electrical circuit diagrams and check mass air flow sensor bank 2 circuit for high resistance, open circuit, short circuit to ground, short circuit to power
  • Check and install a new mass air flow sensor bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P010F-00 Mass or Volume Air Flow Sensor A/B Correlation - No sub type information
NOTE: Customer likely to report hesitation
  • Blocked air cleaner element(s)
  • Leakage from air intake system
  • Blocked engine breather
  • Blockage in air intake system
  • Carbon build-up on throttle blade
  • Blocked catalysts
  • MAF/IAT sensor bank 1 circuit - high resistance, intermittent short circuit to ground, high resistance
  • MAF/IAT sensor bank 1 failure
  • Check air cleaner element is free from restriction
  • Check for leak from air intake system, rectify as required
  • Ensure the engine breather system is correctly installed and in serviceable condition
  • Make sure throttle blade is clean of carbon. Check for blocked catalysts
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor bank 1 sensor circuit for intermittent short circuit to ground, high resistance
  • Check and install a new MAF/IAT sensor bank 1 sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0111-23 Intake Air Temperature Sensor 1 Circuit Range/Performance - Signal stuck low
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_A -
  • Intake air temperature sensor short circuit to ground, open circuit, high resistance
  • Intake air temperature sensor failure
  • Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new intake air temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0111-24 Intake Air Temperature Sensor 1 Circuit Range/Performance - Signal stuck high
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_A -
  • Intake air temperature sensor circuit short circuit to power, open circuit
  • Intake air temperature sensor failure
  • Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short circuit to power, open circuit
  • Check and install a new intake air temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0111-29 Intake Air Temperature Sensor 1 Circuit Range/Performance - Signal invalid
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_A -
  • Intake air temperature sensor circuit short circuit to ground, short circuit to power, open circuit
  • Intake air temperature sensor failure
  • Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new intake air temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0112-00 Intake Air Temperature Sensor 1 Circuit Low (Bank 1) - No sub type information
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_A -
  • Intake air temperature sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Intake air temperature sensor failure
  • Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Check and install a new intake air temperature sensor bank 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0113-00 Intake Air Temperature Sensor 1 Circuit High (Bank 1) - No sub type information
NOTE: - Circuit INLET_AIR_TEMP_SENSOR_A -
  • Intake air temperature sensor circuit short circuit to power, open circuit, high resistance
  • Intake air temperature sensor failure
  • Refer to the electrical circuit diagrams and check intake air temperature sensor circuit for short circuit to power, open circuit, high resistance
  • Check and install a new intake air temperature sensor bank 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0116-23 Engine Coolant Temperature Sensor 1 Circuit Range/Performance - Signal stuck low
NOTE: - Circuit COOLANT_TEMP_SENSOR -
  • Battery reset carried out when the engine was warm/hot
  • Engine coolant temperature sensor 1 sensing circuit intermittent high resistance
  • Engine coolant temperature sensor 1 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357)
  • Check for related DTC P2610- 87. Start the engine and switch off. Clear DTC and re-test
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for intermittent high resistance
  • Check and install a new engine coolant temperature sensor 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0116-24 Engine Coolant Temperature Sensor 1 Circuit Range/Performance - Signal stuck high
NOTE: - Circuit COOLANT_TEMP_SENSOR -
  • Engine coolant temperature sensor 1 sensing circuit intermittent high resistance
  • Engine coolant temperature sensor 1 failure
  • Battery reset carried out when the engine was warm/hot
  • Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357)
  • Check for related DTC P2610- 87. Start the engine and switch off. Clear DTC and re-test
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for intermittent high resistance
  • Check and install a new engine coolant temperature sensor 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0116-29 Engine Coolant Temperature Sensor 1 Circuit Range/Performance - Signal invalid
NOTE: - Circuit COOLANT_TEMP_SENSOR -
  • Low coolant level
  • Engine coolant temperature sensor 1 sensing circuit - intermittent high resistance
  • Engine coolant temperature sensor 1 failure
  • Possible airlock in cooling system
  • Fill cooling system to correct level and specification
  • Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357)
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for intermittent high resistance
  • Check and install new engine coolant temperature sensor 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
  • Bleed cooling system
P0117-16 Engine Coolant Temperature Sensor 1 Circuit Low - Circuit voltage below threshold
NOTE: - Circuit COOLANT_TEMP_SENSOR -
  • Engine coolant temperature sensor 1 circuit short circuit to ground
  • Engine coolant temperature sensor 1 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357)
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for short circuit to ground
  • Check and install a new Engine coolant temperature sensor 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0118-17 Engine Coolant Temperature Sensor 1 Circuit High - Circuit voltage above threshold
NOTE: - Circuit COOLANT_TEMP_SENSOR -
  • Engine coolant temperature sensor 1 circuit short circuit to power, open circuit, sensor disconnected
  • Engine coolant temperature sensor 1 failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Engine Coolant Temperature Sensor Voltage (0x0357)
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for short circuit to power, open circuit, sensor disconnected
  • Check and install new engine coolant temperature sensor 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0121-00 Throttle/Pedal Position Sensor A Circuit Range/Performance - No sub type information
  • Corrupt engine control module software flash
  • Engine control module power supply circuit open circuit, high resistance
  • Engine control module damage through water ingress, internal fault
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Refer to the electrical circuit diagrams and check engine control module power supply circuit for open circuit, high resistance
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0122-00 Throttle/Pedal Position Sensor A Circuit Low - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_1 -
  • Throttle position sensor 1 circuit short circuit to ground, open circuit
  • Throttle position sensor 1 failure
  • Refer to the electrical circuit diagrams and check throttle position sensor 1 circuit for short circuit to ground, open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0123-00 Throttle/Pedal Position Sensor A Circuit High - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_1 -
  • Throttle position sensor 1 circuit short circuit to ground, short circuit to power, open circuit
  • Throttle position sensor 1 failure
  • Refer to the electrical circuit diagrams and check throttle position sensor 1 circuit for short circuit to ground, short circuit to power, open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains suspect the electronic throttle unit
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0125-00 Insufficient Coolant Temp For Closed Loop Fuel Control - No sub type information
  • Coolant temperature sensor 1 circuit, open circuit, high resistance
  • Engine coolant temperature sensor 1 failure
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for open circuit, high resistance
  • Check and install a new engine coolant temperature sensor 1. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0126-26 Insufficient Coolant Temp For Stable Operation - Signal rate of change below threshold
  • Thermostat stuck open
  • Coolant temperature coolant sensor circuit, short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 1 circuit for short circuit to ground, short circuit to power, open circuit
  • Check for related coolant temperature coolant sensor faults. Check and install a new thermostat as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0128-00 Coolant Thermostat (Coolant Temp Below Thermostat Regulating Temperature) - No sub type information
  • Thermostat stuck open
  • Cooling fans running continuously or at a high duty
  • Check for related coolant temperature coolant sensor faults
  • Check cooling fans for correct operation. Repair as required
  • Check and install a new thermostat as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0131-00 O2 Circuit Low Voltage (Bank 1, Sensor 1) - No sub type information
  • Pre-catalyst oxygen sensor odd disconnected
  • Pre-catalyst oxygen sensor odd variable circuit, short circuit to ground
  • Pre-catalyst oxygen sensor odd variable circuit, open circuit
  • Pre-catalyst oxygen sensor odd heater fault
  • Pre-catalyst oxygen sensor odd failure
  • Check pre-catalyst oxygen sensor odd connector is connected
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd variable circuit for short circuit to ground, open circuit
  • Check pre-catalyst oxygen sensor odd heater circuit
  • Check and install a new pre-catalyst oxygen sensor odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0131-1A O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1) - Circuit resistance below threshold
NOTE: - Circuit UHEGO_A_VARIABLE -
  • Pre-catalyst oxygen sensor odd disconnected
  • Pre-catalyst oxygen sensor odd variable circuit, short circuit to ground
  • Pre-catalyst oxygen sensor odd variable circuit, open circuit
  • Pre-catalyst oxygen sensor odd heater fault
  • Pre-catalyst oxygen sensor odd failure
  • Check pre-catalyst oxygen sensor odd connector is connected
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd variable circuit for short circuit to ground, open circuit
  • Check pre-catalyst oxygen sensor odd heater circuit
  • Check and install a new pre-catalyst oxygen sensor odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0132-1B O2 Sensor Circuit High Voltage (Bank 1 Sensor 1) - Circuit resistance above threshold
NOTE: - Circuit UHEGO_A_VARIABLE -
  • Pre-catalyst oxygen sensor odd disconnected
  • Pre-catalyst oxygen sensor odd variable circuit, short circuit to power
  • Pre-catalyst oxygen sensor odd variable circuit, open circuit
  • Pre-catalyst oxygen sensor odd heater fault
  • Pre-catalyst oxygen sensor odd failure
  • Check pre-catalyst oxygen sensor odd connector is connected
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd variable circuit for short circuit to power, open circuit
  • Check pre-catalyst oxygen sensor odd heater circuit
  • Check and install a new pre-catalyst oxygen sensor odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0132-00 O2 Circuit High Voltage (Bank 1, Sensor 1) - No sub type information
  • Pre-catalyst oxygen sensor odd disconnected
  • Pre-catalyst oxygen sensor odd variable circuit, short circuit to power
  • Pre-catalyst oxygen sensor odd variable circuit, open circuit
  • Pre-catalyst oxygen sensor odd heater fault
  • Pre-catalyst oxygen sensor odd failure
  • Check pre-catalyst oxygen sensor odd connector is connected
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd variable circuit for short circuit to power, open circuit
  • Check pre-catalyst oxygen sensor odd heater circuit
  • Check and install a new pre-catalyst oxygen sensor odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0133-00 O2 Circuit Slow Response (Bank 1, Sensor 1) - No sub type information
NOTE: - Circuit UHEGO_A_VARIABLE -
  • Exhaust leak
  • Pre-catalyst oxygen sensor odd to engine control module wiring shield high resistance
  • Fuel control system fault
  • Pre-catalyst oxygen sensor odd failure
  • Check pre-catalyst oxygen sensor odd is correctly installed in exhaust manifold
  • Check for and rectify any exhaust leak between cylinder head and catalytic converter
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd to engine control module wiring shield for high resistance
  • Check fuel control system for failure
  • Check and install a new pre-catalyst oxygen sensor odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0134-00 O2 Circuit No Activity Detected (Bank 1, Sensor 1) - No sub type information
NOTE: - Circuit UHEGO_A_VARIABLE -
  • Pre-catalyst oxygen sensor odd circuit short circuit to ground, short circuit to power, open circuit
  • Pre-catalyst oxygen sensor odd failure
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor odd circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new pre-catalyst oxygen sensor odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0137-00 O2 Circuit Low Voltage (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_A -
  • Post catalyst oxygen sensor - odd, sensing circuit short circuit to ground, high resistance, open circuit
  • Damaged or blocked catalyst
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - odd, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short circuit to ground, high resistance, open circuit
  • Check for damaged or blocked catalyst
  • Check for air leak between catalyst and exhaust manifold
  • Check and install new post catalyst oxygen sensor - odd, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0138-00 O2 Circuit High Voltage (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_A -
  • Post catalyst oxygen sensor - odd, sensing circuit short circuit to power
  • Post catalyst oxygen sensor - odd, tip damaged, blocked, poisoned
  • Catalyst blocked
  • Post catalyst oxygen sensor - odd, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short circuit to power
  • Check post catalyst oxygen sensor - odd, tip for damage, blockage, poisoned, install a new sensor as required
  • Check for blocked catalyst
  • Check and install new catalyst as required. Check and install new post catalyst oxygen sensor - odd, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0139-00 O2 Circuit Slow Response (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_A -
  • Excessive oil consumption
  • Post catalyst oxygen sensor - odd, tip damaged, blocked, poisoned
  • Check for excessive oil consumption. Repair as required
  • Check for related DTCs. Check post catalyst oxygen sensor - odd, tip for damage, blockage, poisoned, install a new sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0140-00 O2 Circuit No Activity Detected (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_A -
  • Post catalyst oxygen sensor - odd, sensing circuit short circuit to ground, short circuit to power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - odd, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - odd, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short circuit to ground, short circuit to power, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check post catalyst oxygen sensor - odd, tip for damage, blockage, poisoned, install a new sensor as required
  • Check for excessive oil consumption. Repair as required
  • Check and install new post catalyst oxygen sensor - odd, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0141-00 O2 Heater Circuit (Bank 1, Sensor 2) - No sub type information
NOTE: - Circuit HTR_HEGO_A -
  • Post catalyst oxygen sensor - odd, sensing circuit short circuit to ground, short circuit to power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor - odd, failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Oxygen Sensor (O2S) Heater Duty Cycle Bank 1 Sensor 2 (0x03A2)
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short circuit to ground, short circuit to power, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install new post catalyst oxygen sensor - odd, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0148-65 Fuel Delivery Error - Signal has too few transitions / events
  • Injector(s) circuit, short circuit to ground, short circuit to power, high resistance
  • Injector(s) failure
  • Engine control module internal failure
  • Check for related injector DTCs
  • Refer to the electrical circuit diagrams and check injector(s) circuit for, short circuit to ground, short circuit to power, high resistance
  • Check and install a new injector(s) as required. Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0148-66 Fuel Delivery Error - Signal has too many transitions / events
  • Injector(s) circuit, short circuit to ground, short circuit to power, high resistance
  • Injector(s) failure
  • Engine control module internal failure
  • Check for related injector DTCs
  • Refer to the electrical circuit diagrams and check injector(s) circuit for, short circuit to ground, short circuit to power, high resistance
  • Check and install a new injector(s) as required. Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0149-32 Fuel Timing Error - Signal low time < minimum
  • Injector(s) circuit, short circuit to ground, short circuit to power, high resistance
  • Injector(s) failure
  • Engine control module internal failure
  • Check for related injector DTCs
  • Refer to the electrical circuit diagrams and check injector(s) circuit for, short circuit to ground, short circuit to power, high resistance
  • Check and install a new injector(s) as required. Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0149-35 Fuel Timing Error - Signal high time > maximum
  • Injector(s) circuit, short circuit to ground, short circuit to power, high resistance
  • Injector(s) failure
  • Engine control module internal failure
  • Check for related injector DTCs
  • Refer to the electrical circuit diagrams and check injector(s) circuit for, short circuit to ground, short circuit to power, high resistance
  • Check and install a new injector(s) as required. Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0151-1A O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1) - Circuit resistance below threshold
NOTE: - Circuit UHEGO_B_VARIABLE -
  • Pre-catalyst oxygen sensor - even circuit short circuit to ground
  • Pre-catalyst oxygen sensor - even failure
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor - even circuit for short circuit to ground
  • Check and install new pre catalyst oxygen sensor - even. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0152-1B O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1) - Circuit resistance above threshold
NOTE: - Circuit UHEGO_B_VARIABLE -
  • Pre-catalyst oxygen sensor - even circuit short circuit to power, disconnected
  • Pre-catalyst oxygen sensor - even failure
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor - even circuit for short circuit to power, disconnected
  • Check and install new pre catalyst oxygen sensor - even. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0153-00 O2 Circuit Slow Response (Bank 2, Sensor 1) - No sub type information
NOTE: - Circuit UHEGO_B_VARIABLE -
  • Exhaust leak
  • Pre-catalyst oxygen sensor even to engine control module wiring shield high resistance
  • Pre-catalyst oxygen sensor even to engine control module signal circuit short circuit to ground
  • Fuel control system fault
  • Pre-catalyst oxygen sensor even failure
  • Check pre-catalyst oxygen sensor even is correctly installed in exhaust manifold
  • Check for and rectify any exhaust leak between cylinder head and catalytic converter
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor even to engine control module wiring shield for high resistance
  • Refer to the electrical circuit diagrams and check Pre-catalyst oxygen sensor even to engine control module signal circuit for short circuit to ground
  • Check fuel control system for failure
  • Check and install a new pre-catalyst oxygen sensor even as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0154-00 O2 Circuit No Activity Detected (Bank 2, Sensor 1) - No sub type information
NOTE: - Circuit UHEGO_B_VARIABLE -
  • Pre-catalyst oxygen sensor even to engine control module wiring shield high resistance
  • Pre-catalyst oxygen sensor even to engine control module signal circuit short circuit to ground, high resistance, open circuit
  • Pre-catalyst oxygen sensor even failure
  • Check pre-catalyst oxygen sensor even is correctly installed in exhaust manifold
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor even to engine control module wiring shield for high resistance
  • Refer to the electrical circuit diagrams and check pre-catalyst oxygen sensor even to engine control module signal circuit for short circuit to ground, high resistance, open circuit
  • Check and install a new pre-catalyst oxygen sensor even as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0157-00 O2 Circuit Low Voltage (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_B -
  • Post catalyst oxygen sensor - even, sensing circuit short circuit to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned
  • Check and install new post catalyst oxygen sensor - even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0158-00 O2 Circuit High Voltage (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_B -
  • Post catalyst oxygen sensor - even, sensing circuit short circuit to power
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to power
  • Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned
  • Check and install new post catalyst oxygen sensor - even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0159-00 O2 Circuit Slow Response (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_B -
  • Excessive oil consumption
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
  • Check for excessive oil consumption, repair as required
  • Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned, install a new sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0160-00 O2 Circuit No Activity Detected (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HEGO_SENSOR_B -
  • Post catalyst oxygen sensor - even, sensing circuit short circuit to ground, short circuit to power, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Post catalyst oxygen sensor - even, tip damaged, blocked, poisoned
  • Post catalyst oxygen sensor - even, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, short circuit to power, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check post catalyst oxygen sensor - even, tip for damage, blockage, poisoned
  • Check and install new post catalyst oxygen sensor - even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0161-00 O2 Heater Circuit (Bank 2, Sensor 2) - No sub type information
NOTE: - Circuit HTR_HEGO_B -
  • Post catalyst oxygen sensor - even, sensing circuit short circuit to ground, short circuit to power, high resistance, open circuit
  • Post catalyst oxygen sensor - even, sensing circuit fuse failure
  • Catalyst oxygen sensor heater circuit control relay failure
  • Post catalyst oxygen sensor - even, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, short circuit to power, high resistance, open circuit
  • Refer to the electrical circuit diagrams and check Post catalyst oxygen sensor - even, sensing circuit fuse, replace as required
  • Refer to the electrical circuit diagrams and check catalyst oxygen sensor heater circuit control relay circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new catalyst oxygen sensor heater control relay, as required. Check and install new post catalyst oxygen sensor - even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0171-00 System Too Lean (Bank 1) - No sub type information
  • Air leak upstream of MAF/IAT sensor bank 1
  • MAF/IAT sensor bank 1 circuit failure
  • MAF/IAT sensor bank 1 failure
  • Pre-catalyst oxygen sensor odd circuit failure
  • Pre-catalyst oxygen sensor odd failure
  • Post-catalyst oxygen sensor odd circuit failure
  • Post-catalyst oxygen sensor odd failure
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor circuit, for short circuit to ground, short circuit power, high resistance, open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, short circuit power, high resistance, open circuit
  • Check for leak from air intake system
  • Check for additional MAF/IAT sensor bank 1 related DTCs and refer to relevant DTC index
  • Check for additional pre-catalyst oxygen sensor odd related DTCs and refer to relevant DTC index
  • Check for additional post-catalyst oxygen sensor odd related DTCs and refer to relevant DTC index
P0172-00 System Too Rich (Bank 1) - No sub type information
  • Restricted air cleaner
  • Leaking fuel injector(s)
  • MAF/IAT sensor bank 1 failure
  • Pre-catalyst oxygen sensor odd circuit failure
  • Pre-catalyst oxygen sensor odd failure
  • Post-catalyst oxygen sensor odd circuit failure
  • Post-catalyst oxygen sensor odd failure
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor circuit, for short circuit to ground, short circuit power, high resistance, open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, short circuit power, high resistance, open circuit
  • Check air cleaner element is free from restriction
  • Check for leaking injectors, install new injector(s) as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
  • Check for additional MAF/IAT sensor bank 1 related DTCs and refer to relevant DTC index
  • Check for additional pre-catalyst oxygen sensor odd related DTCs and refer to relevant DTC index
  • Check for additional post-catalyst oxygen sensor odd related DTCs and refer to relevant DTC index
P0174-00 System Too Lean (Bank 2) - No sub type information
  • Air leak upstream of MAF/IAT sensor bank 2
  • MAF/IAT sensor bank 2 circuit failure
  • MAF/IAT sensor bank 2 failure
  • Pre-catalyst oxygen sensor even circuit failure
  • Pre-catalyst oxygen sensor even failure
  • Post-catalyst oxygen sensor even circuit failure
  • Post-catalyst oxygen sensor even failure
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor circuit, for short circuit to ground, short circuit power, high resistance, open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, short circuit power, high resistance, open circuit
  • Check for leak from air intake system
  • Check for additional MAF/IAT sensor bank 2 related DTCs and refer to relevant DTC index
  • Check for additional pre-catalyst oxygen sensor even related DTCs and refer to relevant DTC index
  • Check for additional post-catalyst oxygen sensor even related DTCs and refer to relevant DTC index
P0175-00 System Too Rich (Bank 2) - No sub type information
  • Restricted air cleaner
  • Leaking fuel injector(s)
  • MAF/IAT sensor bank 2 circuit failure
  • MAF/IAT sensor bank 2 failure
  • Pre-catalyst oxygen sensor even circuit failure
  • Pre-catalyst oxygen sensor even failure
  • Post-catalyst oxygen sensor even circuit failure
  • Post-catalyst oxygen sensor even failure
  • Refer to the electrical circuit diagrams and check MAF/IAT sensor circuit, for short circuit to ground, short circuit power, high resistance, open circuit
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - even, sensing circuit for short circuit to ground, short circuit power, high resistance, open circuit
  • Check for leak from air intake system
  • Check for additional MAF/IAT sensor bank 2 related DTCs and refer to relevant DTC index
  • Check for additional pre-catalyst oxygen sensor even related DTCs and refer to relevant DTC index
  • Check for additional post-catalyst oxygen sensor even related DTCs and refer to relevant DTC index
P018B-29 Fuel Pressure Sensor B Circuit Range/Performance - Signal invalid
NOTE: - Circuit LOW_PRESS_FUEL_PRESS_SENSOR -
  • Fuel Filter or fuel system restriction
  • Fuel system leak
  • Fuel pump pressure sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Fuel pump pressure sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376)
  • Check for related fuel pump DTCs
  • Check the fuel system for restrictions or blockages
  • Refer to the electrical circuit diagrams and check fuel pump pressure sensor circuit for short circuit to power, open circuit, high resistance
  • Check and install a new fuel pump pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P018C-00 Fuel Pressure Sensor B Circuit Low - No sub type information
NOTE: - Circuit LOW_PRESS_FUEL_PRESS_SENSOR -
  • Fuel pump pressure sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Fuel pump pressure sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376)
  • Refer to the electrical circuit diagrams and check fuel pump pressure sensor circuit for short circuit to power, short circuit to ground, open circuit, high resistance
  • Check and install a new fuel pump pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P018D-00 Fuel Pressure Sensor B Circuit High - No sub type information
NOTE: - Circuit LOW_PRESS_FUEL_PRESS_SENSOR -
  • Fuel pump pressure sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Fuel pump pressure sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure - Low Range Sensor Voltage (0x0376)
  • Refer to the electrical circuit diagrams and check fuel pump pressure sensor circuit for short circuit to power, short circuit to ground, open circuit, high resistance
  • Check and install a new fuel pump pressure sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0191-00 Fuel Rail Pressure Sensor A Circuit Range/Performance - No sub type information
NOTE: - Circuit FUEL_HIGH_PRESS_SENSOR -
  • Fuel rail pressure sensor short circuit to ground, short circuit to power, open circuit, high resistance
  • Fuel rail pressure sensor A failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377)
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor A circuit for short circuit to power, short circuit to ground, high resistance, open circuit, terminal damage or corrosion
  • Check and install a new fuel rail pressure sensor A as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0192-00 Fuel Rail Pressure Sensor A Circuit Low - No sub type information
NOTE: - Circuit FUEL_HIGH_PRESS_SENSOR -
  • Fuel rail pressure sensor short circuit to ground, short circuit to power, open circuit, high resistance
  • Fuel rail pressure sensor A failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377)
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor A circuit for short circuit to power, short circuit to ground, high resistance, open circuit, terminal damage or corrosion
  • Check and install a new fuel rail pressure sensor A as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0193-00 Fuel Rail Pressure Sensor A Circuit High - No sub type information
NOTE: - Circuit FUEL_HIGH_PRESS_SENSOR -
  • Fuel rail pressure sensor short circuit to ground, short circuit to power, open circuit, high resistance
  • Fuel rail pressure sensor A failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Fuel Rail Pressure Sensor - High Range Sensor Voltage (0x0377)
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor A circuit for short circuit to power, short circuit to ground, high resistance, open circuit, terminal damage or corrosion
  • Check and install a new fuel rail pressure sensor A as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0196-23 Engine Oil Temperature Sensor Range/Performance - Signal stuck low
NOTE: - Circuit OIL_QUALITY_SENSOR -
  • Oil temperature - level sensor circuit short circuit to ground, high resistance
  • Oil temperature - level sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3)
  • Refer to the electrical circuit diagrams and check oil temperature - level sensor circuit for short circuit to ground, intermittent high resistance
  • Check and install new oil temperature - level sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0196-24 Engine Oil Temperature Sensor Range/Performance - Signal stuck high
NOTE: - Circuit OIL_QUALITY_SENSOR -
  • Oil temperature - level sensor circuit short circuit to power
  • Oil temperature - level sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3)
  • Refer to the electrical circuit diagrams and check oil temperature - level sensor circuit for intermittent short circuit to power
  • Check and install new oil temperature - level sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0200-04 Injector Circuit - System internal failures
  • Engine control module injector circuit power failure
  • Engine control module power supply open circuit
  • Engine control module ground supply open circuit
  • Refer to the electrical circuit diagrams and check engine control module injector power circuit for open circuit
  • Refer to the electrical circuit diagrams and check the power and ground connections to the module
  • Check for misfire DTCs, if present suspect the engine control module
P0200-49 Injector Circuit - Internal electronic failure
  • Engine control module failure
  • Check for misfire DTCs, if present suspect the engine control module
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0200-4B Injector Circuit - Over temperature
  • Engine control module failure
  • If combined with misfire codes for one or both injector sets, then no service rectification is proposed
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0201-13 Cylinder 1 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Fuel injector no. 1 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for open circuit, disconnected injector, high resistance
P0202-13 Cylinder 2 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Fuel injector no. 2 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for open circuit, disconnected injector, high resistance
P0203-13 Cylinder 3 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Fuel injector no. 3 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for open circuit, disconnected injector, high resistance
P0204-13 Cylinder 4 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Fuel injector no. 4 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for open circuit, disconnected injector, high resistance
P0205-13 Cylinder 5 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Fuel injector no. 5 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for open circuit, disconnected injector, high resistance
P0206-13 Cylinder 6 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Fuel injector no. 6 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for open circuit, disconnected injector, high resistance
P0207-13 Cylinder 7 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Fuel injector no. 7 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for open circuit, disconnected injector, high resistance
P0208-13 Cylinder 8 Injector Circuit / Open - Circuit open
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Fuel injector no. 8 circuit open circuit
  • Injector disconnected
  • Injector high resistance
  • Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for open circuit, disconnected injector, high resistance
P0222-00 Throttle/Pedal Position Sensor/Switch B Circuit Low - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_2 -
  • Throttle/pedal position sensor/switch B circuit open circuit, short circuit to ground
  • Throttle/pedal position sensor/switch B failure
  • Refer to the electrical circuit diagrams and check throttle/pedal position sensor/switch B circuit for open circuit, short circuit to ground
  • Check and install a new throttle/pedal position sensor/switch B as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0223-00 Throttle/Pedal Position Sensor/Switch B Circuit High - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_2 -
  • Throttle/pedal position sensor/switch B circuit open circuit, short circuit to power
  • Throttle/pedal position sensor/switch B failure
  • Refer to the electrical circuit diagrams and check throttle/pedal position sensor/switch B circuit for open circuit, short circuit to power
  • Check and install a new throttle/pedal position sensor/switch B as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0231-23 Fuel Pump Secondary Circuit Low - Signal stuck low
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_2NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2POS -
  • Fuel pump driver module signal circuit short circuit to ground, open circuit
  • Fuel pump driver module is not energized with the ignition on
  • Fuel pump driver module failure
  • Check for related DTCs P0232-24
  • Refer to the electrical circuit diagrams and check fuel pump driver module signal circuit for short circuit to ground, open circuit
  • Refer to the electrical circuit diagrams and check fuel pump driver module is energized with the ignition on. Repair as required
  • Check and install a new fuel pump driver module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0232-24 Fuel Pump Secondary Circuit Low - Signal stuck high
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_2NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2POS -
  • Fuel pump driver module signal circuit short circuit to ground, open circuit
  • Fuel pump driver module is not energized with the ignition on
  • Fuel pump driver module failure
  • Check for related DTCs P0231-23
  • Refer to the electrical circuit diagrams and check fuel pump driver module signal circuit for short circuit to ground, open circuit
  • Refer to the electrical circuit diagrams and check fuel pump driver module is energized with the ignition on. Repair as required
  • Check and install a new fuel pump driver module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0251-13 Injection Pump Fuel Metering Control A - Circuit open
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2NEG -
  • Fuel rail pressure sensor circuit, open circuit
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for open circuit
P0253-11 Injection Pump Fuel Metering Control A Low - Circuit short to ground
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2NEG -
  • Fuel rail pressure sensor circuit, short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short circuit to ground
P0254-12 Injection Pump Fuel Metering Control A High - Circuit short to battery
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2NEG -
  • Fuel rail pressure sensor circuit, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short circuit to power
P0256-13 Injection Pump Fuel Metering Control B - Circuit open
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2NEG -
  • Fuel rail pressure sensor circuit, open circuit
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for open circuit
P0258-11 Injection Pump Fuel Metering Control B Low - Circuit short to ground
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2NEG -
  • Fuel rail pressure sensor circuit, short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short circuit to ground
P0259-12 Injection Pump Fuel Metering Control B High - Circuit short to battery
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG - HIGH_PRESS_FUEL_PUMP_CTRL_2NEG -
  • Fuel rail pressure sensor circuit, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel rail pressure sensor circuit for short circuit to power
P025C-14 Fuel Pump Module Control Circuit Low - Circuit short to ground or open
NOTE: - Circuit FPDM control -
  • Fuel pump driver module control circuit, short circuit to ground, open circuit
  • Refer to the electrical circuit diagrams and check fuel pump driver module circuit short circuit to ground, open circuit
P025D-12 Fuel Pump Module Control Circuit High - Circuit short to battery
NOTE: - Circuit FPDM control -
  • Fuel pump driver module control circuit, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel pump driver module circuit short circuit to power
P0261-11 Cylinder 1 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Fuel injector no. 1 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short circuit to ground
P0261-12 Cylinder 1 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Fuel injector no. 1 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short circuit to power
P0262-01 Cylinder 1 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Fuel injector no. 1 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short circuit to ground, short circuit to power
P0262-12 Cylinder 1 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Fuel injector no. 1 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 1 circuit for short circuit to power
P0264-11 Cylinder 2 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Fuel injector no. 2 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short circuit to ground
P0264-12 Cylinder 2 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Fuel injector no. 2 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short circuit to power
P0265-01 Cylinder 2 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Fuel injector no. 2 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short circuit to ground, short circuit to power
P0265-12 Cylinder 2 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Fuel injector no. 2 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 2 circuit for short circuit to power
P0267-11 Cylinder 3 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Fuel injector no. 3 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short circuit to ground
P0267-12 Cylinder 3 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Fuel injector no. 3 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short circuit to power
P0268-01 Cylinder 3 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Fuel injector no. 3 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short circuit to ground, short circuit to power
P0268-12 Cylinder 3 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Fuel injector no. 3 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 3 circuit for short circuit to power
P0270-11 Cylinder 4 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Fuel injector no. 4 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short circuit to ground
P0270-12 Cylinder 4 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Fuel injector no. 4 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short circuit to power
P0271-01 Cylinder 4 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Fuel injector no. 4 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short circuit to ground, short circuit to power
P0271-12 Cylinder 4 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Fuel injector no. 4 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 4 circuit for short circuit to power
P0273-11 Cylinder 5 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Fuel injector no. 5 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short circuit to ground
P0273-12 Cylinder 5 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Fuel injector no. 5 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short circuit to power
P0274-01 Cylinder 5 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Fuel injector no. 5 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short circuit to ground, short circuit to power
P0274-12 Cylinder 5 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Fuel injector no. 5 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 5 circuit for short circuit to power
P0276-11 Cylinder 6 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Fuel injector no. 6 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short circuit to ground
P0276-12 Cylinder 6 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Fuel injector no. 6 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short circuit to power
P0277-01 Cylinder 6 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Fuel injector no. 6 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short circuit to ground, short circuit to power
P0277-12 Cylinder 6 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Fuel injector no. 6 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 6 circuit for short circuit to power
P0279-11 Cylinder 7 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Fuel injector no. 7 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short circuit to ground
P0279-12 Cylinder 7 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Fuel injector no. 7 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short circuit to power
P0280-01 Cylinder 7 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Fuel injector no. 7 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short circuit to ground, short circuit to power
P0280-12 Cylinder 7 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Fuel injector no. 7 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 7 circuit for short circuit to power
P0282-11 Cylinder 8 Injector Circuit Low - Circuit short to ground
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Fuel injector no. 8 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short circuit to ground
P0282-12 Cylinder 8 Injector Circuit Low - Circuit short to battery
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Fuel injector no. 8 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short circuit to power
P0283-01 Cylinder 8 Injector Circuit High - General electrical failure
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Fuel injector no. 8 circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short circuit to ground, short circuit to power
P0283-12 Cylinder 8 Injector Circuit High - Circuit short to battery
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Fuel injector no. 8 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check fuel injector no. 8 circuit for short circuit to power
P02EE-01 Cylinder 1 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Cylinder 1 injector low circuit short circuit to power
  • Cylinder 1 injector low circuit shorted to high circuit
  • Cylinder 1 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 1 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 1 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02EE-1C Cylinder 1 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_1A - INJECTOR_1A_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02EF-01 Cylinder 2 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Cylinder 2 injector low circuit short circuit to power
  • Cylinder 2 injector low circuit shorted to high circuit
  • Cylinder 2 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 2 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 2 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02EF-1C Cylinder 2 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_1B - INJECTOR_1B_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02F0-01 Cylinder 3 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Cylinder 3 injector low circuit short circuit to power
  • Cylinder 3 injector low circuit shorted to high circuit
  • Cylinder 3 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 3 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 3 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02F0-1C Cylinder 3 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_2A - INJECTOR_2A_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02F1-01 Cylinder 4 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Cylinder 4 injector low circuit short circuit to power
  • Cylinder 4 injector low circuit shorted to high circuit
  • Cylinder 4 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 4 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 4 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02F1-1C Cylinder 4 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_2B - INJECTOR_2B_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02F2-01 Cylinder 5 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Cylinder 5 injector low circuit short circuit to power
  • Cylinder 5 injector low circuit shorted to high circuit
  • Cylinder 5 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 5 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 5 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02F2-1C Cylinder 5 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_3A - INJECTOR_3A_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02F3-01 Cylinder 6 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Cylinder 6 injector low circuit short circuit to power
  • Cylinder 6 injector low circuit shorted to high circuit
  • Cylinder 6 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 6 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 6 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02F3-1C Cylinder 6 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_3B - INJECTOR_3B_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02F4-01 Cylinder 7 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Cylinder 7 injector low circuit short circuit to power
  • Cylinder 7 injector low circuit shorted to high circuit
  • Cylinder 7 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 7 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 7 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02F4-1C Cylinder 7 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_4A - INJECTOR_4A_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P02F5-01 Cylinder 8 Injector Circuit Range/Performance - General electrical failure
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Cylinder 8 injector low circuit short circuit to power
  • Cylinder 8 injector low circuit shorted to high circuit
  • Cylinder 8 injector failure
  • Refer to the electrical circuit diagrams and check cylinder 8 injector circuit for short circuit to power, short circuit together
  • Check and install a new cylinder 8 injector as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P02F5-1C Cylinder 8 Injector Circuit Range/Performance - Circuit voltage out of range
NOTE: - Circuit INJECTOR_4B - INJECTOR_4B_COMMON -
  • Engine control module failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
P0300-00 Random Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0301-00 Cylinder 1 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0302-00 Cylinder 2 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0303-00 Cylinder 3 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0304-00 Cylinder 4 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0305-00 Cylinder 5 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0306-00 Cylinder 6 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0307-00 Cylinder 7 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0308-00 Cylinder 8 Misfire Detected - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0313-00 Misfire Detected With Low Fuel - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0316-00 Misfire Detected On Startup (First 1000 Revolutions) - No sub type information
  • Poor fuel quality
  • Catalyst/exhaust system blockage
  • Spark plug(s) fouled or failed
  • Coil(s) failure
  • Injector(s) circuit short circuit to ground, short circuit to power, open circuit
  • Injector(s) failure
  • Fuel system excessively too lean or too rich
  • Camshaft position sensor failure
  • Using the manufacturer approved diagnostic system, check engine control module, for related DTCs and refer to the relevant DTC index
  • Check the fuel system for blockages, repair as required
  • Check the catalyst/exhaust system for blockage, repair as required
  • Check and install a new spark plug(s) as required
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check injector(s) circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new injector(s) as required
  • Check for air leaks within the intake system
  • Check and install a new camshaft position sensor as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0327-00 Knock Sensor 1 Circuit Low (Bank1) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_1A_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 front circuit short circuit to ground, open circuit
  • Knock sensor bank 1 front failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 1 front circuit for short circuit to ground, open circuit
  • Check and install a new knock sensor bank 1 front as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0328-00 Knock Sensor 1 Circuit High (Bank 1) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_1A_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 front circuit high resistance, short circuit to power
  • Knock sensor bank 1 front failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 1 front circuit for short circuit to power, high resistance
  • Check and install a new knock sensor bank 1 front as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P032C-00 Knock Sensor 3 Circuit Low (Bank1) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_2A_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 front circuit short circuit to ground
  • Knock sensor bank 2 front failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 2 front circuit for short circuit to ground
  • Check and install a new knock sensor bank 2 front as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P032D-00 Knock Sensor 3 Circuit High (Bank1) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_2A_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 front circuit high resistance, short circuit to power
  • Knock sensor bank 2 front failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 2 front circuit for short circuit to power, high resistance
  • Check and install a new knock sensor bank 2 front as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0332-00 Knock Sensor 2 Circuit Low (Bank2) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_1B_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 rear circuit short circuit to ground, open circuit
  • Knock sensor bank 1 rear failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 1 rear circuit for short circuit to ground, open circuit
  • Check and install a new knock sensor bank 1 rear as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0333-00 Knock Sensor 2 Circuit High (Bank 2) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_1B_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 1 rear circuit short circuit to power
  • Knock sensor bank 1 rear failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 1 rear circuit for short circuit to power
  • Check and install a new knock sensor bank 1 rear as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0335-02 Crankshaft Position Sensor A Circuit - General signal failure
NOTE: - Circuit CRANK_SENSOR -
  • Crankshaft position sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Crankshaft position sensor failure
  • Refer to the electrical circuit diagrams and check crankshaft position sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check and install new crankshaft position as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0335-31 Crankshaft Position Sensor A Circuit - No signal
NOTE: - Circuit CRANK_SENSOR -
  • Crankshaft position sensor circuit - short circuit to ground, short circuit to power, high resistance, disconnected
  • Crankshaft position sensor failure
  • Refer to the electrical circuit diagrams and check crankshaft position sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check and install new crankshaft position as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0336-00 Crankshaft Position Sensor A Circuit Range/Performance - No sub type information
NOTE: - Circuit CRANK_SENSOR -
  • Crankshaft position sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Crankshaft position sensor gap incorrect, foreign matter on sensor face, damaged teeth on rotor
  • Crankshaft position sensor failure
  • Refer to the electrical circuit diagrams and check crankshaft position sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check crankshaft position sensor for damage and check air gap (check at 90° intervals, should be no greater than 4.5mm)
  • Check and install new crankshaft position as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P033C-00 Knock Sensor 4 Circuit Low (Bank 2) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_2B_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 rear circuit short circuit to ground
  • Knock sensor bank 2 rear failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 2 rear circuit for short circuit to ground
  • Check and install a new knock sensor bank 2 rear as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P033D-00 Knock Sensor 4 Circuit High (Bank 2) - No sub type information
NOTE: - Circuit KNOCK_SENSOR_2B_POS -
  • Poor sensor contact with the cylinder block
  • Knock sensor bank 2 rear circuit high resistance, short circuit to power
  • Knock sensor bank 2 rear failure
  • Ensure a good electrical contact with the cylinder block
  • Refer to the electrical circuit diagrams and check knock sensor bank 2 rear circuit for short circuit to power, high resistance
  • Check and install a new knock sensor bank 2 rear as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0340-02 Camshaft Position Sensor A Circuit (Bank 1 or single sensor) - General signal failure
NOTE: - Circuit CAM_IN_SENSOR_A -
  • Camshaft position sensor bank 1 inlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 1 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 inlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 inlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 1 inlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 1 inlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0340-31 Camshaft Position Sensor A Circuit (Bank 1 or single sensor) - No signal
NOTE: - Circuit CAM_IN_SENSOR_A -
  • Camshaft position sensor bank 1 inlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 1 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 inlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 inlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 1 inlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 1 inlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0341-00 Camshaft Position Sensor A Circuit Range/Performance (Bank 1 or single sensor) - No sub type information
NOTE: - Circuit CAM_IN_SENSOR_A -
  • Camshaft position sensor bank 1 inlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 1 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 inlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 inlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 1 inlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 1 inlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0345-02 Camshaft Position Sensor A Circuit (Bank 2) - General signal failure
NOTE: - Circuit CAM_IN_SENSOR_B -
  • Camshaft position sensor bank 2 inlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 2 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 2 inlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 inlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 2 inlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 2 inlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0345-31 Camshaft Position Sensor A Circuit (Bank 2) - No signal
NOTE: - Circuit CAM_IN_SENSOR_B -
  • Camshaft position sensor bank 2 inlet sensor circuit - short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 2 inlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 2 inlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 inlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 2 inlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 2 inlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0346-00 Camshaft Position Sensor A Circuit Range/Performance (Bank 2) - No sub type information
NOTE: - Circuit CAM_IN_SENSOR_B -
  • Camshaft position sensor bank 2 inlet sensor circuit - short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 2 inlet sensor gap incorrect, foreign matter on sensor face, target rotor run-out
  • Camshaft position sensor bank 2 inlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 inlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 2 inlet sensor for correct installation and damage
  • Check target rotor for run out, repair as required
  • Check and install a new camshaft position sensor bank 2 inlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0351-13 Ignition Coil A Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_1A -
  • Ignition coil 1 open circuit
  • Ignition coil 1 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 1 circuit for open circuit, disconnected ignition coil, high resistance
P0352-13 Ignition Coil B Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_1B -
  • Ignition coil 2 open circuit
  • Ignition coil 2 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 2 circuit for open circuit, disconnected ignition coil, high resistance
P0353-13 Ignition Coil C Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_2A -
  • Ignition coil 3 open circuit
  • Ignition coil 3 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 3 circuit for open circuit, disconnected ignition coil, high resistance
P0354-13 Ignition Coil D Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_2B -
  • Ignition coil 4 open circuit
  • Ignition coil 4 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 4 circuit for open circuit, disconnected ignition coil, high resistance
P0355-13 Ignition Coil E Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_3A -
  • Ignition coil 5 open circuit
  • Ignition coil 5 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 5 circuit for open circuit, disconnected ignition coil, high resistance
P0356-13 Ignition Coil F Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_3B -
  • Ignition coil 6 open circuit
  • Ignition coil 6 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 6 circuit for open circuit, disconnected ignition coil, high resistance
P0357-13 Ignition Coil G Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_4A -
  • Ignition coil 7 open circuit
  • Ignition coil 7 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 7 circuit for open circuit, disconnected ignition coil, high resistance
P0358-13 Ignition Coil H Primary/Secondary Circuit - Circuit open
NOTE: - Circuit IGNITION_4B -
  • Ignition coil 8 open circuit
  • Ignition coil 8 disconnected
  • Ignition coil high resistance
  • Refer to the electrical circuit diagrams and check ignition coil 8 circuit for open circuit, disconnected ignition coil, high resistance
P0365-02 Camshaft Position Sensor B Circuit (Bank 1) - General signal failure
NOTE: - Circuit CAM_EX_SENSOR_A -
  • Camshaft position sensor bank 1 outlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 1 outlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 1 outlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 outlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 1 outlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 1 outlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0366-00 Camshaft Position Sensor B Circuit Range/Performance (Bank 1) - No sub type information
NOTE: - Circuit CAM_EX_SENSOR_A -
  • Camshaft position sensor bank 1 outlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 1 outlet sensor gap incorrect, foreign matter on sensor face, target rotor run-out
  • Camshaft position sensor bank 1 outlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 1 outlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 1 outlet sensor for correct installation and damage
  • Check target run-out, repair as required
  • Check and install a new camshaft position sensor bank 1 outlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0390-02 Camshaft Position Sensor B Circuit (Bank 2) - General signal failure
NOTE: - Circuit CAM_EX_SENSOR_B -
  • Camshaft position sensor bank 2 outlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 2 outlet sensor gap incorrect, foreign matter on sensor face, damaged rotor
  • Camshaft position sensor bank 2 outlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 outlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 2 outlet sensor for correct installation and damage
  • Check and install a new camshaft position sensor bank 2 outlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0391-00 Camshaft Position Sensor B Circuit Range/Performance (Bank 2) - No sub type information
NOTE: - Circuit CAM_EX_SENSOR_B -
  • Camshaft position sensor bank 2 outlet sensor circuit short circuit to ground, short circuit to power, high resistance, disconnected
  • Camshaft position sensor bank 2 outlet sensor gap incorrect, foreign matter on sensor face, damaged rotor, rotor run-out
  • Camshaft position sensor bank 2 outlet sensor failure
  • Refer to the electrical circuit diagrams and check camshaft position sensor bank 2 outlet sensor circuit for short circuit to ground, short circuit to power, high resistance, disconnected
  • Check camshaft position sensor bank 2 outlet sensor for correct installation and damage
  • Check target rotor, repair as required
  • Check and install a new camshaft position sensor bank 2 outlet as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0420-00 Catalyst System Efficiency Below Threshold (Bank 1) - No sub type information
  • Catalytic converter failuredue to overheating damage caused by misfire and/or lean combustion
  • Catalytic converter failuredue to poisoning caused by excessive oil consumption and/or contaminated fuel
  • Using the manufacturer approved diagnostic system, check for misfire/lean combustion related DTCs and refer to the relevant DTC index
  • Check the oil and fuel condition/level
  • Check the catalytic converter for damage
  • Check and install a new catalytic converter bank 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0430-00 Catalyst System Efficiency Below Threshold (Bank 2) - No sub type information
  • Catalytic converter failuredue to overheating damage caused by misfire and/or lean combustion
  • Catalytic converter failuredue to poisoning caused by excessive oil consumption and/or contaminated fuel
  • Using the manufacturer approved diagnostic system, check for misfire/lean combustion related DTCs and refer to the relevant DTC index
  • Check the oil and fuel condition/level
  • Check the catalytic converter for damage
  • Check and install a new catalytic converter bank 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0441-00 Evaporative Emission System Incorrect Purge Flow - No sub type information
NOTE: - Circuit PURGE_VALVE -
  • Evaporative emission system hoses, pipes or connection failure
  • Purge control valve circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Purge control valve failure
  • Check all evaporative emission system hoses, pipes and connection are serviceable, repair/replace as required
  • Refer to the electrical circuit diagrams and check purge control valve circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new purge control valve as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0442-00 Evaporative Emission System Leak Detected (small leak)- No sub type information
  • Fuel filler cap not sealing/missing
  • Diagnostic module tank leakage connector not sealed
  • Purge valve dirty
  • Evaporative emission system leak
  • Fuel tank, filler neck leak
  • Diagnostic module tank leakage module failure
  • Check fuel tank filler cap for sealing/missing. Check and install a new fuel tank filler cap as required
  • Check evaporative emission system for leak using appropriate smoke/leak tester
  • Carry out a purge valve self test to clean the purge valve
  • Check fuel tank and filler neck for leakage, replace as required
  • Check and install a new diagnostic module tank leakage module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0444-13 Evaporative Emission System Purge Control Valve Circuit Open - Circuit open
NOTE: - Circuit PURGE_VALVE -
  • Purge control valve open circuit, high resistance, disconnected
  • Refer to the electrical circuit diagrams and check purge control valve circuit for open circuit, disconnected purge valve, high resistance
P0447-00 Evaporative Emission System Vent Control Circuit Open - No sub type information
NOTE: - Circuit COV -
NOTE: LR - Circuit CHANGE OVER VALVE -
  • Diagnostic module tank leakage module circuit open circuit
  • Diagnostic module tank leakage module circuit fuse blown / not secure in holder
  • Diagnostic module tank leakage module failure
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage module circuit for open circuit
  • Check diagnostic module tank leakage module fuse and replace as required
  • Check and install a new diagnostic module tank leakage module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0448-00 Evaporative Emission System Vent Control Circuit Shorted - No sub type information
NOTE: - Circuit COV -
NOTE: LR - Circuit CHANGE OVER VALVE -
  • Diagnostic module tank leakage module circuit, short circuit to ground, short circuit to power, open circuit
  • Diagnostic module tank leakage module failure
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage module circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new diagnostic module tank leakage module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0456-00 Evaporative Emission System Leak Detected (very small leak) - No sub type information
  • Fuel filler cap not sealing/missing
  • Diagnostic module tank leakage connector not sealed
  • Purge valve dirty
  • Evaporative emission system leak
  • Fuel tank, filler neck leak
  • Diagnostic module tank leakage module failure
  • Check fuel tank filler cap for sealing/missing. Check and install a new fuel tank filler cap as required
  • Check evaporative emission system for leak using appropriate smoke/leak tester
  • Carry out a purge valve self test to clean the purge valve
  • Check fuel tank and filler neck for leakage, replace as required
  • Check and install a new diagnostic module tank leakage module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0458-11 Evaporative Emission System Purge Control Valve Circuit High - Circuit short to ground
NOTE: - Circuit PURGE_VALVE -
  • Evaporative emission system purge control valve circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check evaporative emission system purge control valve circuit for short circuit to ground
P0459-12 Evaporative Emission System Purge Control Valve Circuit High - Circuit short to battery
NOTE: - Circuit PURGE_VALVE -
  • Evaporative emission system purge control valve circuit short circuit to power
  • Refer to the electrical circuit diagrams and check evaporative emission system purge control valve circuit for short circuit to power
P0461-29 Fuel Level Sensor A Circuit Range/Performance - Signal invalid
  • Fuel level sensor circuit open circuit, short circuit to ground, short circuit to power
  • Fuel level sensor stuck
  • Fuel level sensor failure
  • Refer to the electrical circuit diagrams and check fuel level sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check for stuck level sensor
  • Check and install a new fuel level sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0461-2F Fuel Level Sensor A Circuit Range/Performance - Signal erratic
  • Fuel level sensor circuit short circuit to ground, short circuit to power, open circuit
  • Fuel level sensor track damaged
  • Fuel level sensor failure
  • Refer to the electrical circuit diagrams and check fuel level sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check level sensor track for damage
  • Check and install a new fuel level sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0480-13 Fan 1 Control Circuit - Circuit open
NOTE: - Circuit VISCOUS FAN CTRL -
  • Viscous fan control circuit, open circuit
  • Refer to the electrical circuit diagrams and check viscous fan control circuit for open circuit
P0483-00 Fan Performance - No sub type information
NOTE: - Circuit VISCOUS FAN CTRL -
  • Viscous fan control circuit, short circuit to ground, short circuit to power, open circuit
  • Viscous fan unit hydraulic fluid leakage
  • Refer to the electrical circuit diagrams and check viscous fan control circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new viscous fan unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0493-00 Fan Overspeed (clutch locked) - No sub type information
NOTE: - Circuit VISCOUS FAN CTRL -
  • Viscous fan control circuit, short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check viscous fan control circuit for short circuit to ground, short circuit to power, open circuit
P0500-81 Vehicle Speed Sensor A - Invalid serial data received
  • Wheel speed sensor fault
  • Check anti-lock braking system module for related DTCs and refer to relevant DTC index
P0500-82 Vehicle Speed Sensor A - Alive / sequence counter incorrect / not updated
  • Anti-lock braking system module not on bus
  • Check anti-lock braking system module and engine control module for related DTCs and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check anti-lock braking system module circuit for short circuit to ground, short circuit to power, open circuit
P0500-83 Vehicle Speed Sensor A - Value of signal protection calculation incorrect
  • Incorrect level of anti-lock braking system module software
  • Incorrect level of engine control module software
  • Clear DTC and re-test
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the anti-lock braking system module
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
P0500-85 Vehicle Speed Sensor A - Signal above allowable range
  • Anti-lock braking system module has reported a speed above 300 km/h
  • Check anti-lock braking system module for related DTCs and refer to relevant DTC index
P0501-62 Vehicle Speed Sensor A Range/Performance - Signal compare failure
  • Vehicle speed from the anti-lock braking system module does not match the calculated vehicle speed from the engine control module
  • Check engine control module for related vehicle speed DTCs and refer to relevant DTC index
  • Check anti-lock braking system module and transmission control module for related DTCs and refer to relevant DTC index
  • Check the vehicle tire sizes are correct
P0504-00 Brake Switch A / B Correlation - No sub type information
  • No brake pressure signal available from anti-lock braking module
  • Brake switch 1 and Brake switch 2 sense circuit short circuit to ground, short circuit to power, open circuit
  • Brake switch 1 failure
  • Check Anti-Lock braking module for related DTCs and refer to relevant DTC index
  • Check for brake fluid leaks
  • Refer to the electrical circuit diagrams and check anti-lock braking system module circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check brake switch circuit for short circuit to ground, short circuit to power, open circuit
  • Check and install a new brake switch 1 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0504-64 Brake Switch A / B Correlation - Signal plausibility failure
NOTE: - Circuit BRAKE_SW - BRAKE_SW_2 -
  • Brake fluid leak
  • Brake switch incorrectly installed/adjusted
  • Brake switch 1 sense circuit short circuit to Brake switch 2 sense
  • Brake switch failure
  • Check for brake fluid leaks
  • Refer to the electrical circuit diagrams and check brake switch 1 circuit for short circuit to brake switch 2
  • Check brake switch is correctly installed and adjusted
  • Check and install a new brake switch as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0506-00 Idle Air Control System RPM Lower Than Expected - No sub type information
  • Air intake restriction
  • Front end accessory drive overload (defective/seized component)
  • Ensure the air intake system is free from restriction
  • Check the front end accessory drive belt and components for failure, repair as required
P0506-24 Idle Air Control System RPM Lower Than Expected - Signal stuck high
  • Air intake restriction
  • Air intake system air leak between MAF/IAT sensor and throttle
  • Intake air leak between throttle and manifold
  • Engine crankcase breather leak
  • Front end accessory drive overload (defective/seized component)
  • Ensure the air intake system is free from restriction
  • Check for air leak between MAF/IAT sensor and throttle
  • Check for air leak between throttle and inlet manifold
  • Check for engine breather system leak
  • Check the front end accessory drive belt and components for failure
P0507-00 Idle Air Control System RPM Higher Than Expected - No sub type information
  • Air intake system air leak between MAF/IAT sensor and throttle
  • Intake air leak between throttle and manifold
  • Engine crankcase breather leak
  • Check for air leak between MAF/IAT sensor and throttle
  • Check for air leak between throttle and inlet manifold
  • Check for engine breather system leak
P0507-23 Idle Air Control System RPM Higher Than Expected - Signal stuck low
  • Air intake restriction
  • Air intake system air leak between MAF/IAT sensor and throttle
  • Intake air leak between throttle and manifold
  • Engine crankcase breather leak
  • Ensure the air intake system is free from restriction
  • Check for air leak between MAF/IAT sensor and throttle
  • Check for air leak between throttle and inlet manifold
  • Check for engine breather system leak
P050B-23 Cold Start Ignition Timing Performance - Signal stuck low
  • Ignition coil(s)faulty
  • Ignition coils circuit noise
  • Engine control module failure
  • Refer to the electrical circuit diagrams and check ignition coil circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check engine control module to ignition coil circuit for short circuit to power
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check ignition coils circuit for corrosion, high resistance
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P050B-24 Cold Start Ignition Timing Performance - Signal stuck high
  • Ignition coil(s)faulty
  • Ignition coils circuit noise
  • Engine control module failure
  • Refer to the electrical circuit diagrams and check ignition coil circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check engine control module to ignition coil circuit for short circuit to power
  • Check and install a new coil(s) as required
  • Refer to the electrical circuit diagrams and check ignition coils circuit for corrosion, high resistance
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P050E-00 Cold Start Engine Exhaust Temperature Too Low - No sub type information
  • Incorrect coolant temperature sensor installed
  • Coolant temperature sensor circuit short circuit to ground, open circuit
  • Coolant temperature sensor failure
  • Check the correct coolant temperature sensor is installed
  • Refer to the electrical circuit diagrams and check coolant temperature sensor circuit for short circuit to ground, open circuit
  • Check and install a new coolant temperature sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0512-12 Starter Request Circuit - Circuit short to battery
NOTE: - Circuit CRANK_REQUEST -
  • Crank request circuit between engine control module and central junction box short circuit to power
  • Refer to the electrical circuit diagrams and check crank request circuit between engine control module and central junction box for short circuit to power
P0512-14 Starter Request Circuit - Circuit short to ground or open
NOTE: - Circuit CRANK_REQUEST -
  • Crank request circuit between engine control module and central junction box short circuit to ground, open circuit
  • Refer to the electrical circuit diagrams and check crank request circuit between engine control module and central junction box for short circuit to ground, open circuit
P0513-00 Incorrect Immobilizer Key - No sub type information
  • Security key invalid
  • Controller area network data corruption
  • Low battery voltage
  • Check for CAN network interference/engine control module related error
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Check the vehicle charging system for faults, repair as required
P0526-16 Fan Speed Sensor Circuit - Circuit voltage below threshold
NOTE: - Circuit VISCOUS FAN SPEED -
  • Viscous fan circuit, short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check viscous fan circuit for short circuit to ground, short circuit to power, open circuit
P0526-17 Fan Speed Sensor Circuit - Circuit voltage above threshold
NOTE: - Circuit VISCOUS FAN SPEED -
  • Viscous fan circuit, short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check viscous fan circuit for short circuit to ground, short circuit to power, open circuit
P052A-00 Cold Start Intake (A) Camshaft Position Timing Over-Advanced (Bank 1) - No sub type information
NOTE: - Circuit CAM_IN_SENSOR_A -
  • Engine oil pressure too low
  • Intake valve solenoid 1 circuit short circuit to ground, open circuit, high resistance
  • Intake valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check intake valve solenoid 1 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new intake valve solenoid 1 sensor as required
  • Check service history / mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P052B-00 Cold Start Intake (A) Camshaft Position Timing Over-Retarded (Bank 1) - No sub type information
NOTE: - Circuit CAM_IN_SENSOR_A -
  • Engine oil pressure too low
  • Intake valve solenoid 1 circuit short circuit to ground, open circuit, high resistance
  • Intake valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check intake valve solenoid 1 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new intake valve solenoid 1 sensor as required
  • Check service history / mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P052C-00 Cold Start Intake (A) Camshaft Position Timing Over-Advanced (Bank 2) - No sub type information
NOTE: - Circuit CAM_IN_SENSOR_B -
  • Engine oil pressure too low
  • Intake valve solenoid 2 circuit short circuit to ground, open circuit, high resistance
  • Intake valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check intake valve solenoid 2 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new intake valve solenoid 2 sensor as required
  • Check service history /mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P052D-00 Cold Start Intake (A) Camshaft Position Timing Over-Retarded (Bank 2) - No sub type information
NOTE: - Circuit CAM_IN_SENSOR_B -
  • Engine oil pressure too low
  • Intake valve solenoid 2 circuit short circuit to ground, open circuit, high resistance
  • Intake valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check intake valve solenoid 2 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new intake valve solenoid 2 sensor as required
  • Check service history /mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P054A-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Advanced (Bank 1) - No sub type information
NOTE: - Circuit CAM_EX_SENSOR_A -
  • Engine oil pressure too low
  • Exhaust valve solenoid 1 circuit short circuit to ground, open circuit, high resistance
  • Exhaust valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new exhaust valve solenoid 1 sensor as required
  • Check service history /mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P054B-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Retarded (Bank 1) - No sub type information
NOTE: - Circuit CAM_EX_SENSOR_A -
  • Engine oil pressure too low
  • Exhaust valve solenoid 1 circuit short circuit to ground, open circuit, high resistance
  • Exhaust valve solenoid 1 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new exhaust valve solenoid 1 sensor as required
  • Check service history /mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P054C-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Advanced (Bank 2) - No sub type information
NOTE: - Circuit CAM_EX_SENSOR_B -
  • Engine oil pressure too low
  • Exhaust valve solenoid 2 circuit short circuit to ground, open circuit, high resistance
  • Exhaust valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new exhaust valve solenoid 2 sensor as required
  • Check service history /mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P054D-00 Cold Start Exhaust (B) Camshaft Position Timing Over-Retarded (Bank 2) - No sub type information
NOTE: - Circuit CAM_EX_SENSOR_B -
  • Engine oil pressure too low
  • Exhaust valve solenoid 2 circuit short circuit to ground, open circuit, high resistance
  • Exhaust valve solenoid 2 failure
  • Timing chains stretched beyond allowable limits
  • Check engine oil level and top up as required
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 sensor circuit for short circuit to ground, open circuit, high resistance
  • Check and install a new exhaust valve solenoid 2 sensor as required
  • Check service history /mileage
  • Check and install new timing chains as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0560-13 System Voltage - Circuit open
NOTE: - Circuit BATTERY -
  • Engine control module power supply circuit, open circuit
  • Engine control module battery monitor disconnected
  • Refer to the electrical circuit diagrams and check engine control module power supply circuit for open circuit
  • Refer to the electrical circuit diagrams and check engine control module battery monitor circuit for open circuit
P0562-00 System Voltage Low - No sub type information
NOTE: - Circuit BATTERY -
  • Battery circuit high resistance
  • Generator circuit open circuit, high resistance
  • Generator failure
  • Refer to the electrical circuit diagrams and check battery circuit for high resistance
  • Refer to the electrical circuit diagrams and check generator circuit for open circuit, high resistance
  • Check and install a new generator as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0563-00 System Voltage High - No sub type information
NOTE: - Circuit BATTERY -
  • Battery circuit high resistance
  • Generator over charging
  • Refer to the electrical circuit diagrams and check battery circuit for high resistance
  • Check and install a new generator as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0572-17 Brake Switch A Circuit Low - Circuit voltage above threshold
NOTE: - Circuit BRAKE_SW -
  • Brake switch 2 sense circuit short circuit to ground
  • Brake switch incorrectly installed/adjusted
  • Customer is driving with foot resting on brake pedal
  • Brake switch 2 failure
  • Refer to the electrical circuit diagrams and check brake switch 2 circuit for short circuit to ground
  • Check brake switch is correctly installed and adjusted
  • Ensure customer is not driving with foot resting on brake pedal
  • Check and install a new brake switch as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0573-16 Brake Switch A Circuit High - Circuit voltage below threshold
NOTE: - Circuit BRAKE_SW -
  • Brake switch 1 sense circuit short circuit to ground
  • Brake switch 2 sense circuit open circuit
  • Brake switch incorrectly installed/adjusted
  • Customer is driving with foot resting on brake pedal
  • Brake switch 2 failure
  • Refer to the electrical circuit diagrams and check brake switch 1 circuit for open circuit
  • Refer to the electrical circuit diagrams and check brake switch 2 circuit for open circuit
  • Check brake switch is correctly installed and adjusted
  • Ensure customer is not driving with foot resting on brake pedal
  • Check and install a new brake switch as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0578-00 Cruise Control Multi-Function Input A Circuit Stuck - No sub type information
  • Speed control circuit, output signal stuck
  • Speed control switch stuck
  • Refer to the electrical circuit diagrams and check speed control switch circuit for short circuit to ground
  • Check for stuck speed control switch, install a new switch pack as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P057B-87 Brake Pedal Position Sensor Circuit Range/Performance - Missing message
  • Brake pressure signal missing from anti-lock braking system control module
  • Check the anti-lock braking system control module for related DTCs and refer to the relevant DTC index
P0590-00 Cruise Control Multi-Function Input B Circuit Stuck - No sub type information
  • Active speed limiter switch stuck
  • Check for active speed limiter DTCs within gear shift module
  • Check and install a new gear shift module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0600-49 Serial Communication Link - Internal electronic failure
  • Corrupt engine control module software
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0601-43 Internal Control Module Memory Check Sum Error - Special memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0601-45 Internal Control Module Memory Check Sum Error - Program memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0604-42 Internal Control Module Random Access Memory (RAM) Error - General memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0604-43 Internal Control Module Random Access Memory (RAM) Error - Special memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0604-44 Internal Control Module Random Access Memory (RAM) Error - Data memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-00 Internal Control Module Read Only Memory (ROM) Error - No sub type information
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-29 Internal Control Module Read Only Memory (ROM) Error - Signal invalid
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-42 Internal Control Module Read Only Memory (ROM) Error - General memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-44 Internal Control Module Read Only Memory (ROM) Error - Data memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-46 Internal Control Module Read Only Memory (ROM) Error - Calibration / parameter memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-48 Internal Control Module Read Only Memory (ROM) Error - Supervision software failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0605-64 Internal Control Module Read Only Memory (ROM) Error - Signal plausibility failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-01 Control Module Processor - General electrical failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-04 Control Module Processor - System internal failures
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-05 Control Module Processor - System programming failures
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-41 Control Module Processor - General checksum failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-42 Control Module Processor - General memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-43 Control Module Processor - Special memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-44 Control Module Processor - Data memory failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-47 Control Module Processor - Watchdog / safety micro controller failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-48 Control Module Processor - Supervision software failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0606-49 Control Module Processor - Internal electronic failure
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0607-00 Control Module Performance - No sub type information
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0610-43 Control Module Vehicle Options Error - Special memory failure
  • Corrupt engine control module software flash
  • Corrupt rear junction box software flash
  • Corrupt central junction box software flash
  • Clear the DTC and re-test
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Re-configure the rear junction box using the manufacturer approved diagnostic system
  • Re-configure the central junction box using the manufacturer approved diagnostic system
P0615-13 Starter Relay Circuit - Circuit open
NOTE: - Circuit STARTER_RELAY_NEG -
  • Starter relay control circuit open circuit
  • Starter relay failure
  • Refer to the electrical circuit diagrams and check starter relay control circuit for open circuit
  • Check and install a new starter relay as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0616-11 Starter Relay Circuit Low - Circuit short to ground
NOTE: - Circuit STARTER_RELAY_NEG -
  • Starter relay control circuit short circuit to ground
  • Starter relay failure
  • Refer to the electrical circuit diagrams and check starter relay control circuit for short circuit to ground
  • Check and install a new starter relay as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0617-12 Starter Relay Circuit High - Circuit short to battery
NOTE: - Circuit STARTER_RELAY_NEG -
  • Starter relay control circuit short circuit to power
  • Starter relay failure
  • Refer to the electrical circuit diagrams and check starter relay control circuit for short circuit to power
  • Check and install a new starter relay as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P061A-00 Internal Control Module Torque Performance - No sub type information
  • Manifold air flow sensor(s) failure
  • Electronic throttle unit failure
  • Check for related DTCs
  • Check manifold air flow sensors are reading correctly
  • Check and install a new manifold air flow sensor(s) as required
  • Check throttle position sensors are reading the same position
  • Check throttle body is clear of any deposits
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P061A-04 Internal Control Module Torque Performance - System internal failures
  • Manifold air flow sensor(s) failure
  • Electronic throttle unit failure
  • Check for related DTCs
  • Check manifold air flow sensors are reading correctly
  • Check and install a new manifold air flow sensor(s) as required
  • Check throttle position sensors are reading the same position
  • Check throttle body is clear of any deposits
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P061A-29 Internal Control Module Torque Performance - Signal invalid
  • Intake system air leak
  • Manifold air flow sensor(s) failure
  • Throttle position sensors are reading incorrectly
  • Electronic throttle unit failure
  • Atmospheric pressure sensor failure
  • Check for related DTCs
  • Check intake air system for leaks
  • Check manifold air flow sensors are reading correctly
  • Check and install a new air flow sensor(s) as required
  • Check throttle position sensors are reading the same position
  • Check throttle body is clear of any deposits
  • Check and install a new electronic throttle unit as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P061A-64 Internal Control Module Torque Performance - Signal plausibility failure
  • Intake system air leak
  • Manifold air flow sensor(s) failure
  • Check for related DTCs
  • Check intake air system for leaks and is correctly installed
  • Check manifold air flow sensors are reading correctly
  • Check and install a new manifold air flow sensor(s) as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P061B-62 Internal Control Module Torque Calculation Performance - Signal compare failure
  • Intake system air leak
  • Engine breather system leak
  • Manifold air flow sensor failure
  • Electronic throttle unit failure
  • Throttle position sensors are reading incorrectly
  • Atmospheric pressure sensor failure
  • Check intake air system for leaks
  • Check engine breather system for leaks
  • Check throttle position sensors are reading the same position
  • Check and install a new manifold air flow sensor as required
  • Check and install a new electronic throttle unit as required
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0620-01 Generator Control Circuit - General electrical failure
NOTE: - Circuit LIN_A -
  • Generator B+ or battery terminal disconnected/poor connection
  • Charging circuit short, open circuit
  • Generator failure
  • Check for good/clean contact at generator B+ and battery terminal connectors
  • Refer to the electrical circuit diagrams and check charging circuit for short circuit, open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
  • If DTC remains, check and install a new generator as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0627-00 Fuel Pump A Control Circuit / Open - No sub type information
NOTE: - Circuit HIGH_PRESS_FUEL_PUMP_CTRL_1NEG
  • High pressure fuel pump 1 circuit to fuel pump driver module short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the electrical circuit diagrams and check high pressure fuel pump 1 circuit for short circuit to ground, short circuit to power, open circuit, high resistance
P062A-00 Fuel Pump A Control Circuit Range/Performance - No sub type information
  • Invalid fuel pump duty requested by the engine control module
  • Refer to the electrical circuit diagrams and check the fuel pump driver module circuit for short circuit to ground, short circuit to power, open circuit, high resistance
P0630-00 VIN Not Programmed or Incompatible - ECM/PCM - No sub type information
  • Car configuration file to CAN VIN mismatch
  • New engine control module fitted and incorrectly configured
  • New central junction box fitted and incorrectly configured
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module, clear DTC and re-test
  • Re-configure the central junction box using the manufacturer approved diagnostic system, clear DTC and re-test
P0634-22 PCM / ECM/ TCM Internal Temperature Too High - Signal amplitude > maximum
  • Engine control module internal temperature too high
  • Clear the DTC. With the ignition off, wait 10 minutes and re-check DTC
  • Check the engine control module does not have additional external covering or obstructions which may cause overheating
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0634-4B PCM / ECM / TCM Internal Temperature A Too High - Over temperature
  • Engine control module internal temperature too high
  • Clear the DTC. With the ignition off, wait 10 minutes and re-check DTC
  • Check the engine control module does not have additional external covering or obstructions which may cause overheating
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0642-00 Sensor Reference Voltage A Circuit Low - No sub type information
NOTE: - Circuit SENSOR_5V_SUPPLY -
  • Short circuit to power of a 5V output pin, either in the harness, or a connector
  • Internal short circuit in a faulty component
  • Refer to the electrical circuit diagrams and check 5V supply circuit for short circuit to ground open circuit, high resistance, terminal damage or corrosion
  • Check engine control module for sensor related DTCs and refer to the relevant DTC index
P0643-00 Sensor Reference Voltage A Circuit High - No sub type information
NOTE: - Circuit SENSOR_5V_SUPPLY -
  • Short circuit to ground of a 5V output pin, either in the harness, or a connector
  • Internal short circuit in a faulty component
  • Refer to the electrical circuit diagrams and check 5V supply circuit for short circuit to power open circuit, high resistance, terminal damage or corrosion
  • Check engine control module for sensor related DTCs and refer to the relevant DTC index
P065B-16 Generator Control Circuit Range/Performance - Circuit voltage below threshold
NOTE: - Circuit LIN_A -
  • Generator B+ or battery terminal disconnected/poor connection
  • Charging circuit short, open circuit
  • Generator failure
  • Battery failure
  • Check for good/clean contact at generator B+ and battery terminal connectors
  • Refer to the electrical circuit diagrams and check charging circuit for short circuit, open circuit
  • Ensure the battery is in a fully charged and serviceable condition. Refer to the battery care manual and the relevant sections of the workshop manual
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains, check and install a new generator as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P065B-17 Generator Control Circuit Range/Performance - Circuit voltage above threshold
NOTE: - Circuit LIN_A -
  • Charging circuit short circuit to power
  • Generator failure
  • Battery failure
  • Check for good/clean contact at generator B+ and battery terminal connectors
  • Refer to the electrical circuit diagrams and check charging circuit for short circuit, open circuit
  • Ensure the battery is in a fully charged and serviceable condition. Refer to the battery care manual and the relevant sections of the workshop manual
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system. If DTC remains, check and install a new generator as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P065C-00 Generator Mechanical Performance - No sub type information
NOTE: - Circuit LIN_A -
  • Poor front end accessory belt tension
  • Generator pulley loose/failure
  • Generator failure
  • Check front end accessory belt for condition/contamination and correct tension
  • Check generator pulley for failure
  • Clear DTC and repeat automated diagnostic procedure using manufacturer approved diagnostic system
  • If DTC remains check and install a new generator as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0660-13 Intake Manifold Tuning Valve Control Circuit Low - Bank 1 - Circuit open
NOTE: - Circuit IMTV -
NOTE: LR - Circuit MANIFOLD TUNING VALVE -
  • Intake manifold tuning valve circuit open circuit
  • Refer to the electrical circuit diagrams and check intake manifold tuning valve circuit for open circuit
P0661-11 Intake Manifold Tuning Valve Control Circuit Low - Bank 1 - Circuit short to ground
NOTE: - Circuit IMTV -
NOTE: LR - Circuit MANIFOLD TUNING VALVE -
  • Intake manifold tuning valve circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check intake manifold tuning valve circuit for short circuit to ground
P0662-12 Intake Manifold Tuning Valve Control Circuit Low - Bank 1 - Circuit short to battery
NOTE: - Circuit IMTV -
NOTE: LR - Circuit MANIFOLD TUNING VALVE -
  • Intake manifold tuning valve circuit short circuit to power
  • Refer to the electrical circuit diagrams and check manifold tuning valve circuit for short circuit to power
P0668-00 PCM / ECM / TCM Internal Temperature Sensor A Circuit Low - No sub type information
  • Engine control module internal temperature sensor failure
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0669-00 PCM / ECM / TCM Internal Temperature Sensor A Circuit High - No sub type information
  • Engine control module internal temperature sensor failure
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0687-73 ECM/PCM Power Relay Control Circuit High - Actuator stuck closed
NOTE: - Circuit EMS_MAIN_RLY -
  • Engine control module relay circuit short circuit to power
  • Engine control module relay failure
  • Refer to the electrical circuit diagrams and check engine control module relay circuit for short circuit to power
  • Check and install a new engine control module relay as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0691-11 Fan 1 Control Circuit Low - Circuit short to ground
NOTE: LR - Circuit VISCOUS FAN CTRL -
  • Viscous fan circuit, short circuit to ground
  • Viscous fan control module failure
  • Refer to the electrical circuit diagrams and check viscous fan circuit for short circuit to ground
  • Check and install a new viscous fan as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0692-12 Fan 1 Control Circuit High - Circuit short to battery
NOTE: LR - Circuit VISCOUS FAN CTRL -
  • Viscous fan circuit, short circuit to power
  • Viscous fan control module failure
  • Refer to the electrical circuit diagrams and check viscous fan circuit for short circuit to power
  • Check and install a new viscous fan as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0721-85 Output Shaft Speed Sensor Circuit Range/Performance - Signal above allowable range
  • Transmission control module has reported a fault in the shaft speed signal
  • Check transmission control module for related DTCs and refer to relevant DTC index
P0721-86 Output Shaft Speed Sensor Circuit Range/Performance - Signal invalid
  • Transmission control module has taken to 8 seconds or longer to change range
  • Check transmission control module for related DTCs and refer to relevant DTC index
P0724-17 Brake Switch B Circuit High - Circuit voltage above threshold
NOTE: - Circuit BRAKE_SW -
  • Brake switch 1 sense circuit short circuit to power
  • Brake switch incorrectly installed/adjusted
  • Customer is driving with foot resting on brake pedal
  • Brake switch 1 failure
  • Refer to the electrical circuit diagrams and check brake switch 1 circuit for short circuit to power
  • Check brake switch is correctly installed and adjusted
  • Ensure customer is not driving with foot resting on brake pedal
  • Check and install a new brake switch as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P0850-86 Park / Neutral Switch Input Circuit - Signal invalid
NOTE: - Circuit PN_SW -
  • Intermittent fault on Park/Neutral signal from gear shift module
  • CAN network failure between gear shift module and engine control module
  • Check gear shift module for related DTCs and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check Park/Neutral switch input circuit for short circuit to ground, short circuit to power, open circuit
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P0850-8F Park / Neutral Switch Input Circuit - Erratic
NOTE: - Circuit PN_SW -
  • Intermittent fault on Park/Neutral signal from gear shift module
  • CAN network failure between gear shift module and engine control module
  • Check gear shift module for related DTCs and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check Park/Neutral switch input circuit for short circuit to ground, short circuit to power, open circuit
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P0851-14 Park / Neutral Switch Input Circuit Low - Circuit short to ground or open
NOTE: - Circuit PN_SW -
  • Park/Neutral switch input circuit short circuit to ground, open circuit
  • Refer to the electrical circuit diagrams and check park/neutral switch input circuit for short circuit to ground, open circuit
P0852-12 Park / Neutral Switch Input Circuit Low - Circuit short to battery
NOTE: - Circuit PN_SW -
  • Park/Neutral switch input circuit short circuit to power
  • Refer to the electrical circuit diagrams and check park/neutral switch input circuit for short circuit to power
P0A1A-87 Generator Control Module - Missing message
NOTE: - Circuit LIN_A -
  • Generator to engine control module LIN circuit open circuit
  • Check for good/clean contact at generator and engine control module LIN circuit connectors/pins
  • Refer to the electrical circuit diagrams and check generator circuit for open circuit
  • Check for engine control module hardware DTCs and refer to relevant DTC index
  • Clear DTCs and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
P0A1A-88 Generator Control Module - Bus off
NOTE: - Circuit LIN_A -
  • Generator to engine control module LIN circuit open circuit
  • Check for good/clean contact at generator and engine control module LIN circuit connectors/pins
  • Refer to the electrical circuit diagrams and check generator circuit for open circuit
  • Check for engine control module hardware DTCs and refer to relevant DTC index
  • Clear DTCs and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
P0A3B-00 Generator Over Temperature - No sub type information
  • Cooling fan not operating
  • Coolant level low
  • Check for correct cooling fan operation
  • Check coolant level. Clear DTC and re-test
P0A3B-68 Generator Over Temperature - Event information
  • Cooling fan not operating
  • Coolant level low
  • Check for correct cooling fan operation
  • Check coolant level. Clear DTC and re-test
P115D-00 Mass Air Flow Circuit Offset - No sub type information
NOTE: - Circuit MAF_SENSOR_A - MAF_SENSOR_B -
    NOTE: Customer likely to report hesitation.
  • Air cleaner blocked
  • Air intake leak
  • Engine breather blocked
  • Air intake blockage
  • Carbon build up on throttle blade
  • Mass air flow sensor circuit, high resistance
  • Blocked catalyst(s)
  • Mass air flow sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Mass Air Flow Sensor 2 Voltage (0x0503)
  • Check air cleaner for blockage
  • Check air intake system for leaks
  • Check engine breather system for blockages
  • Check for carbon build up on throttle blade
  • Check for related mass air flow DTCs P0102 or P0103
  • Refer to the electrical circuit diagrams and check mass air flow sensor circuit for high resistance
  • Check and install a new mass air flow sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P1315-00 Persistent Misfire - No sub type information
  • Engine control module to ignition coil primary circuit fault (cylinder misfire detected DTC also flagged)
  • Fuel injector circuit fault(s) (injector DTCs also flagged)
  • Fuel delivery pressure low
  • Spark plug failure/fouled/incorrect gap
  • Ignition coil failure
  • Cylinder compression low
  • Exhaust system blockage
  • Check for cylinder mis-fire, ignition and injector DTCs and refer to the DTC index
  • Refer to the electrical circuit diagrams and check ignition coil circuit for short circuit to ground, short circuit to power, open circuit
  • Check for fuel system failure
  • Check and install a new spark plug(s) as required
  • Check and install a new ignition coil as required
  • Carry out cylinder compression tests
  • Check exhaust system for blockage
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P1316-00 Injector Driver Module Codes Detected - No sub type information
  • Engine control module to ignition coil primary circuit fault (cylinder misfire detected DTC also flagged)
  • Fuel injector circuit fault(s) (injector DTCs also flagged)
  • Fuel delivery pressure low
  • Spark plug failure/fouled/incorrect gap
  • Ignition coil failure
  • Cylinder compression low
  • Exhaust system blockage
  • Check for cylinder mis-fire, ignition and injector DTCs and refer to the DTC index
  • Refer to the electrical circuit diagrams and check ignition coil circuit for short circuit to ground, short circuit to power, open circuit
  • Check for fuel system failure
  • Check and install a new spark plug(s) as required
  • Check and install a new ignition coil as required
  • Carry out cylinder compression tests
  • Check exhaust system for blockage
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P1593-64 Cruise Control Monitor Fault - Signal plausibility failure
  • Speed control monitor fault. The engine control module performs a independent check of the cruise status
  • Using the manufacturer approved diagnostic system check and up-date the car configuration file as required. Clear the DTC and retest. If the problem persists, contact dealer technical support
P1603-00 EEPROM Malfunction - No sub type information
  • Corrupt engine control module software flash
  • Engine control module power supply fault
  • Engine control module damage through water ingress
  • Using the manufacturer approved diagnostic system check and install latest relevant level of software to the engine control module
  • Refer to the electrical circuit diagrams and check engine control module power supply circuit for open circuit
  • Check engine control module for signs of water ingress
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2088-11 A Camshaft Position Actuator Control Circuit Low Bank 1 - Circuit short to ground
NOTE: - Circuit VFS_IN_A -
  • Intake valve solenoid 1 short circuit to ground
  • Refer to the electrical circuit diagrams and check intake valve solenoid 1 for short circuit to ground
P2089-12 A Camshaft Position Actuator Control Circuit High Bank 1 - Circuit short to battery
NOTE: - Circuit VFS_IN_A -
  • Intake valve solenoid 1 short circuit to power
  • Refer to the electrical circuit diagrams and check intake valve solenoid 1 for short circuit to power
P2090-11 B Camshaft Position Actuator Control Circuit Low Bank 1 - Circuit short to ground
NOTE: - Circuit VFS_EX_A -
  • Exhaust valve solenoid 1 short circuit to ground
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 for short circuit to ground
P2091-12 B Camshaft Position Actuator Control Circuit High Bank 1 - Circuit short to battery
NOTE: - Circuit VFS_EX_A -
  • Exhaust valve solenoid 1 short circuit to power
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 1 for short circuit to power
P2092-11 A Camshaft Position Actuator Control Circuit Low Bank 2 - Circuit short to ground
NOTE: - Circuit VFS_IN_B -
  • Intake valve solenoid 2 short circuit to ground
  • Refer to the electrical circuit diagrams and check intake valve solenoid 2 for short circuit to ground
P2093-12 A Camshaft Position Actuator Control Circuit High Bank 2 - Circuit short to battery
NOTE: - Circuit VFS_IN_B -
  • Intake valve solenoid 2 short circuit to power
  • Refer to the electrical circuit diagrams and check intake valve solenoid 2 for short circuit to power
P2094-11 B Camshaft Position Actuator Control Circuit Low Bank 2 - Circuit short to ground
NOTE: - Circuit VFS_EX_B -
  • Exhaust valve solenoid 2 short circuit to ground
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 for short circuit to ground
P2095-12 B Camshaft Position Actuator Control Circuit High Bank 2 - Circuit short to battery
NOTE: - Circuit VFS_EX_B -
  • Exhaust valve solenoid 2 short circuit to power
  • Refer to the electrical circuit diagrams and check exhaust valve solenoid 2 for short circuit to power
P2096-00 Post Catalyst Fuel Trim System Too Lean Bank 1 - No sub type information
NOTE: - Circuit HEGO_SENSOR_A -
  • Post catalyst oxygen sensor odd, sensing circuit short circuit to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor odd, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short circuit to ground, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check for air leak between the two oxygen sensors
  • Check and install new post catalyst oxygen sensor odd, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2097-00 Post Catalyst Fuel Trim System Too Rich Bank 1 - No sub type information
NOTE: - Circuit HEGO_SENSOR_A -
  • Post catalyst oxygen sensor odd, sensing circuit short circuit to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor odd, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor - odd, sensing circuit for short circuit to ground, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check for air leak between the two oxygen sensors
  • Check and install new post catalyst oxygen sensor odd, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2098-00 Post Catalyst Fuel Trim System Too Lean Bank 2 - No sub type information
NOTE: - Circuit HEGO_SENSOR_B -
  • Post catalyst oxygen sensor even, sensing circuit short circuit to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor even, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor even, sensing circuit for short circuit to ground, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check for air leak between the two oxygen sensors
  • Check and install new post catalyst oxygen sensor even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2099-00 Post Catalyst Fuel Trim System Too Rich Bank 2 - No sub type information
NOTE: - Circuit HEGO_SENSOR_B -
  • Post catalyst oxygen sensor even, sensing circuit short circuit to ground, high resistance, open circuit
  • Air leak between catalyst and exhaust manifold
  • Air leak between the two oxygen sensors
  • Post catalyst oxygen sensor even, failure
  • Refer to the electrical circuit diagrams and check post catalyst oxygen sensor even, sensing circuit for short circuit to ground, high resistance, open circuit
  • Check for air leak between catalyst and exhaust manifold
  • Check for air leak between the two oxygen sensors
  • Check and install new post catalyst oxygen sensor even, as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2105-00 Throttle Actuator Control System - Forced Engine Shutdown - No sub type information
NOTE: - Circuit THROTTLE_MOTOR_NEG - THROTTLE_MOTOR_POS -
  • Engine speed or torque limitation has been activated as a result of engine control module, throttle pedal position sensor, or torque faults
  • Check for any DTCs relating to engine control module, throttle pedal position sensor, or torque faults and refer to the DTC index
P2118-19 Throttle Actuator Control Motor Current Range/Performance - Circuit current above threshold
NOTE: - Circuit THROTTLE_MOTOR_NEG - THROTTLE_MOTOR_POS -
  • Throttle motor control circuit short circuit to ground, short circuit to power, high resistance
  • Engine control module ground circuit fault
  • Carbon build-up on throttle blade
  • Electronic throttle unit failure
  • Refer to the electrical circuit diagrams and check electronic throttle unit circuit for short circuit to ground, short circuit to power, high resistance
  • Refer to the electrical circuit diagrams and check engine control module ground circuit for faults
  • Make sure throttle blade is clean of carbon
  • Check the system is operating correctly and the DTC does not return
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2119-00 Throttle Actuator Control Throttle Body Range/Performance - No sub type information
NOTE: - Circuit THROTTLE_MOTOR_NEG - THROTTLE_MOTOR_POS -
  • Carbon build-up on throttle blade
  • Engine control module ground circuit fault
  • Electronic throttle unit return spring faulty
  • Electronic throttle unit limp home spring faulty
  • Make sure throttle blade is clean of carbon
  • Refer to the electrical circuit diagrams and check engine control module ground circuit for faults
  • Check the system is operating correctly and the DTC does not return
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2119-29 Throttle Actuator Control Throttle Body Range/Performance - Signal invalid
NOTE: - Circuit THROTTLE_MOTOR_NEG - THROTTLE_MOTOR_POS -
  • Stuck / sticking throttle blade
  • Electronic throttle unit failure
  • Ensure throttle blade is free of any carbon build-up / other obstructions
  • Check the system is operating correctly and the DTC does not return
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2119-64 Throttle Actuator Control Throttle Body Range/Performance - Signal plausibility failure
NOTE: - Circuit THROTTLE_MOTOR_NEG - THROTTLE_MOTOR_POS -
  • Stuck / sticking throttle blade
  • Electronic throttle unit failure
  • Ensure throttle blade is free of any carbon build-up / other obstructions
  • Check the system is operating correctly and the DTC does not return
  • Check and install a new electronic throttle unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2122-00 Throttle/Pedal Position Sensor/Switch D Circuit Low - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_1 -
  • Accelerator pedal position sensor 1 circuit short circuit to ground, open circuit
  • Accelerator pedal position sensor 1, VREF circuit open circuit
  • Accelerator pedal position sensor 1 failure
  • Refer to the electrical circuit diagrams and check accelerator pedal unit, accelerator pedal position sensor 1 circuit for short circuit to ground, open circuit
  • Check accelerator pedal unit, VREF circuit for open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
  • If DTC remains, check and install a new accelerator pedal unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2123-00 Throttle/Pedal Position Sensor/Switch D Circuit High - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_1 -
  • Accelerator pedal position sensor 1 circuit short circuit to power
  • Accelerator pedal position sensor 1, VREF circuit open circuit
  • Accelerator pedal position sensor 1 failure
  • Refer to the electrical circuit diagrams and check accelerator pedal unit, accelerator pedal position sensor 1 circuit for short circuit to power
  • Check accelerator pedal unit, VREF circuit for open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
  • If DTC remains, check and install a new accelerator pedal unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2127-00 Throttle/Pedal Position Sensor/Switch E Circuit Low - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_2 -
  • Accelerator pedal position sensor 2 circuit short circuit to ground, open circuit
  • Accelerator pedal position sensor 2, VREF circuit open circuit
  • Accelerator pedal position sensor 2 failure
  • Refer to the electrical circuit diagrams and check accelerator pedal unit, accelerator pedal position sensor 2 circuit for short circuit to ground, open circuit
  • Check accelerator pedal unit, VREF circuit for open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
  • If DTC remains, check and install a new accelerator pedal unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2128-00 Throttle/Pedal Position Sensor/Switch E Circuit High - No sub type information
NOTE: - Circuit THROTTLE_POSITION_SENSOR_2 -
  • Accelerator pedal position sensor 2 circuit short circuit to power
  • Accelerator pedal position sensor 2, VREF circuit open circuit
  • Accelerator pedal position sensor 2 failure
  • Refer to the electrical circuit diagrams and check accelerator pedal unit, accelerator pedal position sensor 2 circuit for short circuit to power
  • Check accelerator pedal unit, VREF circuit for open circuit
  • Clear DTC and repeat automated diagnostic procedure using the manufacturer approved diagnostic system
  • If DTC remains, check and install a new accelerator pedal unit as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2135-00 Throttle/Pedal Position Sensor/Switch A / B Voltage Correlation - No sub type information
  • Throttle pedal position sensor circuit 1 and 2 short circuit to ground, short circuit to power, open circuit
 Refer to the electrical circuit diagrams and check throttle pedal position sensor circuit 1 and 2 for short circuit to ground, short circuit to power, open circuit
P2135-09 Throttle/Pedal Position Sensor/Switch A / B Voltage Correlation - Component Failures
  • Throttle pedal position sensor circuit 1 and 2 short circuit to ground, short circuit to power, open circuit
 Refer to the electrical circuit diagrams and check throttle pedal position sensor circuit 1 and 2 for short circuit to ground, short circuit to power, open circuit
P2138-64 Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation - No sub type information
  • Accelerator pedal position sensor circuit 1 and 2 short circuit to ground, short circuit to power, open circuit
 Refer to the electrical circuit diagrams and check accelerator pedal position sensor circuit 1 and 2 for short circuit to ground, short circuit to power, open circuit
P2183-23 Engine Coolant Temperature Sensor 2 Circuit Range/Performance - Signal stuck low
NOTE: - Circuit COOLANT_TEMP_SENSOR_2 -
  • Engine coolant temperature sensor 2 circuit high resistance, open circuit
  • Engine coolant temperature sensor 2 failure
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for high resistance, open circuit
  • Check and install a new engine coolant temperature sensor 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2183-24 Engine Coolant Temperature Sensor 2 Circuit Range/Performance - Signal stuck high
NOTE: - Circuit COOLANT_TEMP_SENSOR_2 -
  • Engine coolant temperature sensor 2 circuit short circuit to power
  • Engine coolant temperature sensor 2 failure
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for short circuit to power
  • Check and install a new engine coolant temperature sensor 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2183-29 Engine Coolant Temperature Sensor 2 Circuit Range/Performance - Signal invalid
NOTE: - Circuit COOLANT_TEMP_SENSOR_2 -
  • Engine coolant temperature sensor 2 circuit high resistance, open circuit, short circuit to ground, short circuit to power
  • Engine coolant temperature sensor 2 failure
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for high resistance, open circuit, short circuit to ground, short circuit to power
  • Check and install a new engine coolant temperature sensor 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2184-16 Engine Coolant Temperature Sensor 2 Circuit Low - Circuit voltage below threshold
NOTE: - Circuit COOLANT_TEMP_SENSOR_2 -
  • Engine coolant temperature sensor 2 circuit high resistance, open circuit, short circuit to ground
  • Engine coolant temperature sensor 2 failure
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for high resistance, open circuit, short circuit to ground
  • Check and install a new engine coolant temperature sensor 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2185-17 Engine Coolant Temperature Sensor 2 Circuit High - Circuit voltage above threshold
NOTE: - Circuit COOLANT_TEMP_SENSOR_2 -
  • Ignition turned on with an ambient temperature of below -40c
  • Engine coolant temperature sensor 2 circuit short circuit to power
  • Engine coolant temperature sensor 2 failure
  • Clear the DTC and re-test
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor 2 circuit for short circuit to power
  • Check and install a new engine coolant temperature sensor 2 as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P219A-00 Bank 1 Air-Fuel Ratio Imbalance - No sub type information
NOTE: Post catalyst oxygen sensor-odd & Pre catalyst oxygen sensor-odd
  • Other oxygen sensor related DTCs
  • Air leak in the exhaust system between post catalyst oxygen sensor-odd and catalyst
  • Air leak in the exhaust system between catalyst and exhaust manifold flange
  • Air leak in the exhaust system between pre catalyst oxygen sensor-odd and post catalyst oxygen sensor-odd
  • Air leak around pre catalyst oxygen sensor-odd
  • Air leaks within the intake system
  • Air leak around fuel injector(s) bank 1
  • Air leak around spark plug(s) bank 1
  • Low fuel pressure, fuel injector(s) leak, fuel system leak bank 1
  • camshaft position actuator sticking
  • Airpath blockage between throttle butterfly and inlet poppet valve
  • Post catalyst oxygen sensor-odd failure
  • Cylinder head gasket failure
  • Using the manufacturer approved diagnostic system check the engine control module for oxygen sensor related DTCs and refer to the relevant DTC index. Record any available freeze frame data
  • Check for air leaks in the exhaust system between post catalyst oxygen sensor-odd and catalyst
  • Check for air leaks in the exhaust system between catalyst and exhaust manifold flange
  • Check for air leaks in the exhaust system between pre catalyst oxygen sensor-odd and post catalyst oxygen sensor-odd
  • Check for air leaks around pre catalyst oxygen sensor-odd
  • Check for air leaks within the intake system
  • Check for air leak around fuel injector(s) bank 1
  • Check for air leak around spark plug(s) bank 1
  • Check for low fuel pressure, fuel injector(s) leak, fuel system leak bank 1
  • Check for camshaft position actuator sticking
  • Check for airpath blockage between throttle butterfly and inlet poppet valve
  • Carry out cylinder compression check. Record the results
  • Check and install a post catalyst oxygen sensor-odd as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
  • Using the manufacturer approved diagnostic system clear DTC and retest
P219B-00 Bank 2 Air-Fuel Ratio Imbalance - No sub type information
NOTE: Post catalyst oxygen sensor-even & Pre catalyst oxygen sensor-even
  • Other oxygen sensor related DTCs
  • Air leak in the exhaust system between post catalyst oxygen sensor-even and catalyst
  • Air leak in the exhaust system between catalyst and exhaust manifold flange
  • Air leak in the exhaust system between pre catalyst oxygen sensor-even and post catalyst oxygen sensor-even
  • Air leak around pre catalyst oxygen sensor-even
  • Air leaks within the intake system
  • Air leak around fuel injector(s) bank 2
  • Air leak around spark plug(s) bank 2
  • Low fuel pressure, fuel injector(s) leak, fuel system leak bank 2
  • camshaft position actuator sticking
  • Airpath blockage between throttle butterfly and inlet poppet valve
  • Post catalyst oxygen sensor-even failure
  • Cylinder head gasket failure
  • Using the manufacturer approved diagnostic system check the engine control module for oxygen sensor related DTCs and refer to the relevant DTC index. Record any available freeze frame data
  • Check for air leaks in the exhaust system between post catalyst oxygen sensor-even and catalyst
  • Check for air leaks in the exhaust system between catalyst and exhaust manifold flange
  • Check for air leaks in the exhaust system between pre catalyst oxygen sensor-even and post catalyst oxygen sensor-even
  • Check for air leaks around pre catalyst oxygen sensor-even
  • Check for air leaks within the intake system
  • Check for air leak around fuel injector(s) bank 2
  • Check for air leak around spark plug(s) bank 2
  • Check for low fuel pressure, fuel injector(s) leak, fuel system leak bank 2
  • Check for camshaft position actuator sticking
  • Check for airpath blockage between throttle butterfly and inlet poppet valve
  • Carry out cylinder compression check. Record the results
  • Check and install a post catalyst oxygen sensor-even as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
  • Using the manufacturer approved diagnostic system clear DTC and retest
P2228-00 Barometric Pressure Circuit Low - No sub type information
  • Barometric pressure sensor failure (internal engine control module failure)
  • Using the manufacturer approved diagnostic system check datalogger signal, Barometric Pressure Sensor Voltage (0x035A)
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2229-00 Barometric Pressure Circuit Low - No sub type information
  • Barometric pressure sensor failure(internal engine control module failure)
  • Using the manufacturer approved diagnostic system check datalogger signal, Barometric Pressure Sensor Voltage (0x035A)
  • Check and install a new engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2279-00 Intake Air System Leak - No sub type information
  • Part load breather pipe disconnected
  • Brake vacuum pipe disconnected
  • Excessive intake air leak
  • Check for related DTCs
  • Check part load breather pipe for leaks or disconnected
  • Check brake vacuum pipe for leaks or disconnected
  • Check intake air system for leaks
P2300-11 Ignition Coil A Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_1A -
  • Ignition coil 1 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 1 circuit for short circuit to ground
P2301-12 Ignition Coil A Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_1A -
  • Ignition coil 1 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 1 circuit for short circuit to power
P2303-11 Ignition Coil B Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_1B -
  • Ignition coil 2 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 2 circuit for short circuit to ground
P2304-12 Ignition Coil B Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_1B -
  • Ignition coil 2 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 2 circuit for short circuit to power
P2306-11 Ignition Coil C Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_2A -
  • Ignition coil 3 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 3 circuit for short circuit to ground
P2307-12 Ignition Coil C Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_2A -
  • Ignition coil 3 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 3 circuit for short circuit to power
P2309-11 Ignition Coil D Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_2B -
  • Ignition coil 4 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 4 circuit for short circuit to ground
P2310-12 Ignition Coil D Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_2B -
  • Ignition coil 4 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 4 circuit for short circuit to power
P2312-11 Ignition Coil E Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_3A -
  • Ignition coil 5 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 5 circuit for short circuit to ground
P2313-12 Ignition Coil E Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_3A -
  • Ignition coil 5 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 5 circuit for short circuit to power
P2315-11 Ignition Coil F Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_3B -
  • Ignition coil 6 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 6 circuit for short circuit to ground
P2316-12 Ignition Coil F Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_3B -
  • Ignition coil 6 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 6 circuit for short circuit to power
P2318-11 Ignition Coil G Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_4A -
  • Ignition coil 7 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 7 circuit for short circuit to ground
P2319-12 Ignition Coil G Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_4A -
  • Ignition coil 7 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 7 circuit for short circuit to power
P2321-11 Ignition Coil H Primary Control Circuit Low - Circuit short to ground
NOTE: - Circuit IGNITION_4B -
  • Ignition coil 8 circuit short circuit to ground
  • Refer to the electrical circuit diagrams and check ignition coil 8 circuit for short circuit to ground
P2322-12 Ignition Coil H Primary Control Circuit High - Circuit short to battery
NOTE: - Circuit IGNITION_4B -
  • Ignition coil 8 circuit short circuit to power
  • Refer to the electrical circuit diagrams and check ignition coil 8 circuit for short circuit to power
P2401-00 Evaporative Emission System Leak Detection Pump Control Circuit Low - No sub type information
NOTE: - Circuit FUEL_LEAK_PUMP -
  • Diagnostic module tank leakage fuse failure
  • Diagnostic module tank leakage circuit short circuit to ground, open circuit
  • Diagnostic module tank leakage failure
  • Check diagnostic module tank leakage fuse for failure and security in holder
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage circuit for short circuit to ground, open circuit
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2402-00 Evaporative Emission System Leak Detection Pump Control Circuit High - No sub type information
NOTE: - Circuit FUEL_LEAK_PUMP -
  • Diagnostic module tank leakage circuit short circuit to power
  • Diagnostic module tank leakage failure
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage circuit for short circuit to power
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2404-29 Evaporative Emission System Leak Detection Pump Sense Circuit Range/Performance - Signal invalid
NOTE: - Circuit FUEL_LEAK_PUMP -
  • Diagnostic module tank leakage failure
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2404-2F Evaporative Emission System Leak Detection Pump Sense Circuit Range/Performance - Signal erratic
NOTE: - Circuit FUEL_LEAK_PUMP -
  • Diagnostic module tank leakage failure
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2405-00 Evaporative Emission System Leak Detection Pump Sense Circuit Low - No sub type information
NOTE: - Circuit FUEL_LEAK_PUMP -
  • Diagnostic module tank leakage circuit short circuit to ground, high resistance, open circuit
  • Diagnostic module tank leakage failure
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage circuit for short circuit to ground, high resistance, open circuit
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2406-00 Evaporative Emission System Leak Detection Pump Sense Circuit High - No sub type information
NOTE: - Circuit FUEL_LEAK_PUMP -
  • Blockage in diagnostic module tank leakage ventilation pipe
  • Diagnostic module tank leakage circuit, open circuit
  • Check for blockage in the Blockage in diagnostic module tank leakage ventilation pipe
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P240A-00 Evaporative Emission System Leak Detection Pump Heater Circuit / Open - No sub type information
NOTE: - Circuit PUMP_HEATER_CONTROL -
  • Diagnostic module tank leakage circuit, open circuit
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage heater circuit for open circuit
P240B-00 Evaporative Emission System Leak Detection Pump Heater Circuit Low - No sub type information
NOTE: - Circuit PUMP_HEATER_CONTROL -
  • Diagnostic module tank leakage heater circuit short circuit to ground, high resistance
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage heater circuit for short circuit to ground, high resistance
P240C-00 Evaporative Emission System Leak Detection Pump Heater Circuit High - No sub type information
NOTE: - Circuit PUMP_HEATER_CONTROL -
  • Diagnostic module tank leakage heater circuit short circuit to power
  • Refer to the electrical circuit diagrams and check diagnostic module tank leakage heater circuit for short circuit to power
P2450-00 Evaporative Emission Control System Switching Valve Performance/Stuck Open - No sub type information
NOTE: - Circuit COV -
NOTE: LR - Circuit CHANGE OVER VALVE -
  • Diagnostic module tank leakage failure
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2451-00 Evaporative Emission Control System Switching Valve Performance/Stuck Closed - No sub type information
NOTE: - Circuit COV -
NOTE: LR - Circuit CHANGE OVER VALVE -
  • Diagnostic module tank leakage failure
  • Check and install a new diagnostic module tank leakage as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P250C-23 Engine Oil Level Sensor Circuit Low - Signal stuck low
NOTE: - Circuit OIL_QUALITY_SENSOR -
  • Oil temperature level sensor circuit short circuit to ground
  • Oil temperature level sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3)
  • Refer to the electrical circuit diagrams and check oil temperature level sensor circuit for short circuit to ground
  • Check and install a new oil temperature level sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P250D-24 Engine Oil Level Sensor Circuit High - Signal stuck high
NOTE: - Circuit OIL_QUALITY_SENSOR -
  • Oil temperature level sensor circuit short circuit to power
  • Oil temperature level sensor failure
  • Using the manufacturer approved diagnostic system check datalogger signal, Sump Oil Temperature - Measured (0x03F3)
  • Refer to the electrical circuit diagrams and check oil temperature level sensor circuit for short circuit to power
  • Check and install a new oil temperature level sensor as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
P2544-64 Torque Management Request Input Signal A - Signal plausibility failure
  • Inappropriate request from anti-lock braking system
  • Check for related DTCs within anti-lock braking system module and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P2544-92 Torque Management Request Input Signal A - Performance or incorrect operation
  • Inappropriate request from anti-lock braking system
  • Check for related DTCs within anti-lock braking system module and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P2610-00 ECM/PCM Internal Engine Off Timer Performance - No sub type information
  • Instrument cluster fault
  • Central junction box fault
  • CAN network error
  • Check for DTCs related to any of the components listed and refer to relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P2610-84 ECM/PCM Engine Off Timer Performance - Signal below allowable range
  • Instrument cluster fault
  • Central junction box fault
  • Engine coolant temperature sensor fault
  • Ambient temperature sensor fault
  • Low battery voltage
  • CAN network error
  • Check for DTCs related to any of the components listed and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check the battery voltage, repair as required
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P2610-85 ECM/PCM Engine Off Timer Performance - Signal above allowable range
  • Instrument cluster fault
  • Central junction box fault
  • Engine coolant temperature sensor fault
  • Ambient temperature sensor fault
  • Low battery voltage
  • CAN network error
  • Check for DTCs related to any of the components listed and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Check the battery voltage, repair as required
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P2610-87 ECM/PCM Internal Engine Off Timer Performance - Missing message
  • Instrument cluster fault
  • Central junction box fault
  • Engine coolant temperature sensor fault
  • Ambient temperature sensor fault
  • CAN network error
  • Check for DTCs related to any of the components listed, and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check engine coolant temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Refer to the electrical circuit diagrams and check ambient air temperature sensor circuit for short circuit to ground, short circuit to power, open circuit
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
P2772-64 Four Wheel Drive (4WD) Low Switch Circuit Range/Performance - Signal plausibility failure
  • Missing data in the car configuration file
  • Vehicle speed related failure
  • Gearbox output shaft speed related failure
  • Using the manufacturer approved diagnostic system check and up-date the car configuration file as required. Clear the diagnostic trouble code and retest
  • Using the manufacturer approved diagnostic system check for vehicle speed related DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system check for gearbox output shaft speed related DTCs and refer to the relevant DTC index
  • Clear the diagnostic trouble code and re-test
U0001-88 High Speed CAN Communication Bus - Bus off
NOTE: - Circuit HS_CAN_NEG - HS_CAN_POS -
  • High speed CAN bus circuit, short circuit to ground
  • High speed CAN bus circuit, short circuit to power
  • High speed CAN bus, open circuit
  • Refer to the electrical circuit diagrams and check CAN network for short circuit to ground, short circuit to power, open circuit
  • Using the manufacturer approved diagnostic system, carry out network integrity test
U0101-00 Lost Communication with TCM - No sub type information
  • CAN link engine control module/transmission control module network malfunction
  • Transmission control module failure
  • Using the manufacturer approved diagnostic system, check transmission control module for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check transmission control module power and ground circuit for open circuit
  • Check CAN harness to transmission control module, repair as necessary
U0102-00 Lost Communication with Transfer Case Control Module - No sub type information
  • CAN harness link between engine control module and transfer box control module network malfunction
  • Using the manufacturer approved diagnostic system, check transfer box control module for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check transfer box control module power and ground circuits for open circuit
  • Check CAN harness between engine control module and transfer box control module, repair as necessary
U0104-00 Lost Communication With Cruise Control Module - No sub type information
  • Vehicle configured for speed control, but speed control module is not installed
  • CAN Link engine control module/speed control module network malfunction
  • Speed control module power or ground circuit, open circuit
  • Check vehicle has correct speed control module installed
  • Using the manufacturer approved diagnostic system, check speed control module, anti-lock braking system module for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check speed control module power and ground circuit for open circuit
  • Check CAN harness to speed control module, repair as necessary
U0121-00 Lost Communication With Anti-lock Braking System (ABS) Control Module - No sub type information
  • CAN Link engine control module/anti-lock braking system module network malfunction
  • Anti-lock braking system module power or ground circuit, open circuit
  • Using the manufacturer approved diagnostic system, check anti-lock braking system module for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check anti-lock braking system module power and ground circuit for open circuit
  • Check CAN harness to anti-lock braking system module, repair as necessary
U0126-00 Lost Communication With Steering Angle Sensor Module - No sub type information
  • CAN harness link between engine control module and steering angle sensor network malfunction
  • Using the manufacturer approved diagnostic system, steering angle sensor for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check steering angle sensor power and ground circuits for open circuit
  • Check CAN harness between engine control module and steering angle sensor, repair as necessary
U0128-00 Lost Communication With Park Brake Control Module - No sub type information
  • CAN Link engine control module/electronic parking brake signal missing network malfunction
  • Refer to the electrical circuit diagrams and check power and ground supplies to electronic parking brake
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0132-00 Lost Communication with Suspension Control Module A - No sub type information
  • CAN link/suspension control module network malfunction
  • Refer to the electrical circuit diagrams and check power and ground supplies to suspension control module
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0133-00 Lost Communication With Active Roll Control Module - No sub type information
  • CAN harness link between engine control module and active roll control module network malfunction
  • Using the manufacturer approved diagnostic system, check active roll control module for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check active roll control module power and ground circuits for open circuit
  • Check CAN harness between engine control module and active roll control module, repair as necessary
U0138-00 Lost Communication with All Terrain Control Module - No sub type information
  • CAN harness link between engine control module and center console switch pack network malfunction
  • Using the manufacturer approved diagnostic system, check center console switch pack for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check center console switch pack power and ground circuits for open circuit
  • Check CAN harness between engine control module and center console switch pack, repair as necessary
U0140-00 Lost Communication With Body Control Module - No sub type information
  • CAN harness link between engine control module and central junction box network malfunction
  • Using the manufacturer approved diagnostic system, check central junction box for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check central junction box power and ground circuits for open circuit
  • Check CAN harness between engine control module and central junction box, repair as necessary
U0151-00 Lost Communication with Restraints Control Module - No sub type information
  • Lost communication with restraints control module over CAN or hardwired link
  • Refer to the electrical circuit diagrams and check power and ground supplies to restraints control module
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0151-87 Lost Communication with Restraints Control Module - Missing message
  • Lost communication due to restraints control module fault
  • Check restraints control module for associated DTCs and refer to relevant DTC index
  • Refer to the electrical circuit diagrams and check power and ground supplies to restraints control module
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0155-00 Lost Communication with Instrument Panel Cluster (IPC) - No sub type information
  • CAN link between engine control module and instrument cluster fault
  • Refer to the electrical circuit diagrams and check power and ground supplies to instrument cluster
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0167-00 Lost Communication with Vehicle Immobilizer Control Module - No sub type information
  • Security challenge response timeout
  • Battery fault
  • Refer to the electrical circuit diagrams and check power and ground supplies to the electric steering column lock
  • Check for related CAN DTCs and refer to the relevant DTC index
  • Ensure the battery is in a fully charged and serviceable condition. Refer to the battery care manual and the relevant sections of the workshop manual
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0300-00 Internal Control Module Software Incompatibility - No sub type information
  • Engine control module has incorrect software installed
  • The engine control module is in expulsion mode. An incorrect specification engine control module has been installed to the vehicle
  • Check and install the correct engine control module software
  • Check and install the correct engine control module as required. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U0402-00 Invalid Data Received From Transmission Control Module - No sub type information
  • Transmission engine control module request corruption
  • Using the manufacturer approved diagnostic system, check transmission control module, for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short circuit, open circuit
U0402-08 Invalid Data Received from TCM - Bus signal / message failures
  • Transmission engine control module request corruption
  • High speed CAN bus circuit failure, short, open circuit
  • Using the manufacturer approved diagnostic system, check transmission control module, for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short circuit, open circuit
U0402-64 Invalid Data Received from TCM - Signal plausibility failure
  • Transmission to engine control module request corruption
  • High speed CAN bus signal corruption
  • Using the manufacturer approved diagnostic system, check transmission control module, for DTCs and refer to the relevant DTC index
  • Using the manufacturer approved diagnostic system, complete a CAN network integrity test
  • Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short circuit, open circuit
U0402-82 Invalid Data Received from TCM - Alive / sequence counter incorrect / not updated
  • Transmission control module shaft-speed faults
  • Using the manufacturer approved diagnostic system, check transmission control module, for DTCs and refer to the relevant DTC index
U0402-83 Invalid Data Received from TCM - Value of signal protection calculation incorrect
  • Transmission control module shaft-speed faults
  • Using the manufacturer approved diagnostic system, check transmission control module, for DTCs and refer to the relevant DTC index
U0415-00 Invalid Data Received From Anti-lock Braking System (ABS) Control Module - No sub type information
  • Electronic throttle unit, throttle position sensor 1 failure
  • Electronic throttle unit, throttle position sensor 2 failure
  • Electronic throttle unit harness short, open circuit
  • Using the manufacturer approved diagnostic system, check for electronic throttle unit DTCs repair as necessary
  • Refer to the electrical circuit diagrams and check electronic unit harness for short circuit, open circuit
  • Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U0415-64 Invalid Data Received From Anti-lock Braking System (ABS) (ABS) Control Module - Signal plausibility failure
  • Invalid request from anti-lock braking system
  • Torque up request higher than expected from anti-lock braking system
  • Using the manufacturer approved diagnostic system, check anti-lock braking system, for DTCs and refer to the relevant DTC index
  • Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short circuit, open circuit
U0415-67 Invalid Data Received From Anti-lock Braking System (ABS) (ABS) Control Module - Signal incorrect after event
  • Torque up request higher than expected from anti-lock braking system
  • Using the manufacturer approved diagnostic system, check anti-lock braking system, for DTCs and refer to the relevant DTC index
  • Refer to the electrical circuit diagrams and check high speed CAN bus circuit for short circuit, open circuit
U0426-00 Invalid Data Received From Vehicle Immobilizer Control Module - No sub type information
  • Security code mis-match
  • This DTC will be logged if the encrypted data exchange does not match between engine control module and the instrument cluster or central junction box
  • Check CAN network between engine control module, instrument cluster and central junction box
  • Refer to the electrical circuit diagrams and check power and ground circuit to engine control module and instrument cluster
  • Check correct engine control module and instrument cluster installed
  • Re-synchronise ID by re-configuring the engine control module and instrument cluster as new modules
U0447-81 Invalid Data Received From Gateway "A" - Invalid serial data received
  • The LIN to high speed CAN gateway has informed the engine control module of a failure
  • This DTC has been inhibited in the engine control module, as the LIN bus flag is set during normal operation
scientia non olet · About LEMON Manuals