Instrument Cluster (IPC): DTCs

INSTRUMENT CLUSTER (IPC) DTCs

DTC	Description	Possible Causes	Action
B1009-51	Ignition Authorization - Not programmed	Ignition authorization not programmed	Configure the Instrument Cluster using the manufacturers approved diagnostic system
B1009-87	Ignition Authorization - Missing message	Ignition authorization message missing	Configure the Instrument Cluster using the manufacturers approved diagnostic system
B100D-64	Column Lock Authorization - Signal plausibility failure	Steering Column Lock system/Steering Column Lock unable to perform lock action CAN Fault Anti-lock Braking System, Engine Control Module, Central Junction Box fault	NOTE: Prior to clearing this DTC, carry out the 'Vehicle Functional Reset' application using the manufacturer approved diagnostic system. Check the serviceability of the steering column and lock. Clear the DTC and retest. If the problem persists, carry out CAN Network Integrity test and Module Self Test using the manufacturer approved diagnostic system. Refer to the electrical circuit diagrams and check CAN network
B1026-12	Steering Column Lock - Circuit short to battery	Steering column lock circuit short to power	Refer to the wiring diagrams and check the electric steering column ground circuit
B108E-13	Display - Circuit open	Cluster display connector fails continuity check Continuity circuit in display flex cable open circuit	Renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
B10B7-86	Rear Air Discharge Temperature - Signal invalid	Display illumination area temperature sensor signal is out of range	Check the harness connector to the Instrument Cluster for security and integrity. Clear the DTC and retest the switch function. If the problem persists, renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
B115C-7A	Transfer Fuel Pump - Fluid leak or seal failure	Transfer fuel pump fault Fluid leak or seal failure	Check for other fuel pump related DTCs. Renew the transfer fuel (jet) pump
B1264-13	Control Module Connector(s) Loose Or Disconnected - Circuit open	Display not adequately connected to Instrument Cluster circuit board	Suspect the Instrument Cluster, install a new Instrument Cluster as necessary. Refer to the Warranty Policy and Procedures information if a module is suspect
B1264-49	Control Module Connector(s) Loose Or Disconnected - Internal electronic failure	Airbag Telltale not adequately connected to Instrument Cluster circuit board	Suspect the Instrument Cluster, install a new Instrument Cluster as necessary. Refer to the Warranty Policy and Procedures information if a module is suspect
B1264-95	Control Module Connector(s) Loose Or Disconnected - Incorrect assembly	Security Telltale not adequately connected to Instrument Cluster circuit board	Suspect the Instrument Cluster, install a new Instrument Cluster as necessary. Refer to the Warranty Policy and Procedures information if a module is suspect
B12FE-09	Fan - Component Failures	Cooling fan is stalled/not running at full speed	Check for foul condition at fan
B12FE-12	Fan - Circuit short to battery	Cooling fan ground cannot be applied. Short to power	Refer to the electrical circuit diagrams and check cooling fan ground circuit for short to power
B12FE-13	Fan - Circuit open	Cooling fan ground cannot be applied. Open circuit	Refer to the electrical circuit diagrams and check cooling fan ground for broken wire, open circuit
B1A14-96	RCM Warning Lamp - Component internal failure	SRS LED failure Warning lamp circuit fault	Check the harness connector to the Instrument Cluster for security and integrity. Clear the DTC and retest the switch function. If the problem persists, renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
B1A68-86	Ambient Temperature Sensor - Signal invalid	Internal board temperature sensor signal is out of range/invalid	Check the harness connector to the Instrument Cluster for security and integrity. Clear the DTC and retest the switch function. If the problem persists, renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
B1A85-96	Ambient Light Sensor - Component internal failure	Internal light sensor failure	Check the harness connector to the Instrument Cluster for security and integrity. Clear the DTC and retest the switch function. If the problem persists, renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
P0485-12	Fan Power/Ground Circuit - Circuit short to battery	Fan power/ground circuit short to power	Refer to the electrical wiring diagrams and check the cluster cooling fan circuit and rectify as necessary. Clear the DTC and retest
P0607-4B	Control Module Performance - Over temperature	Cluster over temperature	Check the cluster cooling fan/circuit and rectify as necessary. Clear the DTC and retest
P060A-08	Internal Control Module Monitoring Processor Performance - Bus Signal/Message Failures	Internal communication errors are causing lock-ups and resets	Suspect the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
P0610-55	Control Module Vehicle Options Error - Not configured	Control module incorrectly configured	Configure the module using the manufacturers approved diagnostic system
U0001-88	High Speed CAN Communication Bus - Bus off	CAN Bus off	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network
U0010-88	Medium Speed CAN Communication Bus - Bus off	Bus off	Carry out the CAN Network Integrity Test using the Manufacturer approved diagnostic system. Alternatively, refer to the electrical circuit diagrams and check CAN network to Instrument Cluster
U0100-00	Lost Communication With ECM/PCM "A" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Engine Control Module and Instrument Cluster
U0101-00	Lost Communication with TCM - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Transmission Control Module and Instrument Cluster
U0102-00	Lost Communication with Transfer Case Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Transfer Case Control Module and Instrument Cluster
U0104-00	Lost Communication With Cruise Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Speed Control Module and Instrument Cluster
U0121-00	Lost Communication With Anti-Lock Brake System (ABS) Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Anti-lock Braking System Module and Instrument Cluster.
U0126-00	Lost Communication With Steering Angle Sensor Module - no sub type information	Power or ground circuit fault CAN Bus circuit fault Module internal failure	Refer to the electrical circuit diagrams and check the power, ground and CAN Bus circuit to the steering angle sensor for fault. Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0127-00	Lost Communication With Tire Pressure Monitor Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Tire Pressure Monitoring System Module and Instrument Cluster
U0128-00	Lost Communication With Park Brake Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Parking Brake Module and Instrument Cluster
U0132-00	Lost Communication With Suspension Control Module "A" - no sub type information	Power or ground circuit fault CAN Bus circuit fault Module internal failure	Refer to the electrical circuit diagrams and check the power, ground and CAN Bus circuits to the air suspension module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0136-00	Lost Communication With Differential Control Module - Rear - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Rear Differential Control Module and Instrument Cluster.
U0138-00	Lost Communication with All Terrain Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Terrain Response Control Module and Instrument Cluster
U0139-00	Lost Communication With Suspension Control Module "B" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Suspension Control Module and Instrument Cluster.
U0139-08	Lost Communication With Suspension Control Module "B" - Bus Signal/Message Failures	Bus signal/message failures	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Suspension Control Module and Instrument Cluster
U0140-00	Lost Communication With Body Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Central Junction Box and Instrument Cluster
U0141-00	Lost Communication With Body Control Module "A" - no sub type information	Power or ground circuit fault CAN Bus circuit fault Module internal failure	Refer to the electrical circuit diagrams and check the power, ground and CAN Bus circuit to the body control module for fault. Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0151-00	Lost Communication With Restraints Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Restraints Control Module and Instrument Cluster
U0154-00	Lost Communication With Restraints Occupant Classification System Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Restraints Control Module and Instrument Cluster
U0159-00	Lost Communication With Parking Assist Control Module "A" - No sub type information	CAN Link Instrument Cluster /parking aid module missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Parking Aid Module and Instrument Cluster
U0164-00	Lost Communication With HVAC Control Module - No sub type information	CAN Link Instrument Cluster/HVAC module missing message	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Climate Control Module and Instrument Cluster
U0184-00	Lost Communication With Radio - no sub type information	Power or ground circuit fault CAN Bus circuit fault Module internal failure	Refer to the electrical circuit diagrams and check the power, ground and CAN Bus circuit to the audio head unit for fault. Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0199-00	Lost Communication With "Door Control Module A" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Door Control Module and Instrument Cluster
U0208-00	Lost Communication With "Seat Control Module A" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Seat Control Module and Instrument Cluster
U0214-00	Lost Communication With Remote Function Actuation - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Remote Function Actuation Module and Instrument Cluster
U0232-00	Lost Communication With Side Obstacle Detection Control Module - Left - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Side Object Detection module and Instrument Cluster
U0241-00	Lost Communication With Headlamp Control Module "A" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Headlamp Control Module and Instrument Cluster
U0242-00	Lost Communication With Headlamp Control Module "B" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Headlamp Control Module and Instrument Cluster
U0264-00	Lost Communication With Camera Module- Rear - no sub type information	Power or ground circuit fault CAN Bus circuit fault Module internal failure	Refer to the electrical circuit diagrams and check the power, ground and CAN Bus circuit to the rear view camera for fault. Using the manufacturer approved diagnostic system, complete a CAN network integrity test
U0300-00	Internal Control Module Software Incompatibility - No sub type information	No sub type information	Check for other modules reporting CAN Bus off or lost communication faults. If other modules report problems, check the software version in the Central Junction Box using the manufacturers approved diagnostic system. If no other modules report problems, check the software version in the Instrument Cluster. Update/configure as necessary
U0402-68	Invalid Data Received from TCM - Event information	Event information	Check for transmission Control module DTCs. Refer to relevant DTC index
U1A00-00	Private Communication Network - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the LIN Bus circuit
U2013-02	Switch Pack - General signal failure	General signal failure	Refer to the electrical circuit diagrams and check the LIN Bus circuit
U2013-08	Switch Pack - Bus Signal/Message Failures	General signal failure	Refer to the electrical circuit diagrams and check the LIN Bus circuit
U3000-46	Control Module - Calibration/parameter memory failure	Odometer reading on cluster is missing or incorrect - calibration / parameter memory failure	Check the harness connector to the Instrument Cluster for security and integrity. Clear the DTC and retest. If the problem persists, renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
U3000-49	Control Module - Internal electronic failure	Internal electronic failure	Check the harness connector to the Instrument Cluster for security and integrity. Clear the DTC and retest. If the problem persists, renew the Instrument Cluster. Refer to the warranty policies and procedures before renewing the module
U3000-55	Control Module - Not configured	Speedometer is inaccurate Tire size compensation is incorrectly configured	Using the manufacturer approved diagnostic system select the vehicle configuration main menu, select configure existing modules menu and program the module
U3000-87	Control Module - Missing message	Car configuration file missing message	Configure the car config file using the approved diagnostic system
U3002-81	Vehicle Identification Number - Invalid serial data received	Invalid vehicle identification number	Configure the car config file using the approved diagnostic system
U3003-16	Control Module - Circuit voltage below threshold	Circuit voltage below threshold (9V)	Check vehicle battery and charging system. Refer to the relevant instructions in the workshop information. Refer to the electrical circuit diagrams and check the power supply circuits to the module
U3003-17	Control Module - Circuit voltage above threshold .	Circuit voltage above threshold (16V)	Check vehicle battery and charging system. Refer to the relevant instructions in the workshop information. Refer to the electrical circuit diagrams and check the power supply circuits to the module
U3003-62	Control Module - Signal compare failure	Signal compare failure	Check vehicle battery and charging system. Refer to the relevant instructions in the workshop information. Refer to the electrical circuit diagrams and check the power supply circuits to the module