Anti-Lock Braking System (Abs): DTCs

ANTI-LOCK BRAKING SYSTEM (ABS) DTCs

DTC	Description	Possible Causes	Action
C0030-38	Left Front Tone Wheel - Signal frequency incorrect	Signal frequency incorrect Damaged ABS sensor ring	Check front left wheel speed sensor ring for missing teeth or damage. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0031-14	Left Front Wheel Speed Sensor - Circuit short to ground or open	Sensor short circuit to ground or open circuit Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C0031-25	Left Front Wheel Speed Sensor - Signal shape/waveform failure	Sensor short circuit to ground Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0031-2F	Left Front Wheel Speed Sensor - Signal erratic	Sensor circuit fault Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0031-31	Left Front Wheel Speed Sensor - No signal	No sensor signal Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0031-62	Left Front Wheel Speed Sensor - Signal compare failure	Sensor signal compare failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0031-64	Left Front Wheel Speed Sensor - Signal plausibility failure	Sensor signal plausibility failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C0033-38	Right Front Tone Wheel - Signal frequency incorrect	Signal frequency incorrect Damaged ABS sensor ring	Check front right wheel speed sensor ring for missing teeth or damage. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0034-14	Right Front Wheel Speed Sensor - Circuit short to ground or open	Sensor short circuit to ground or open Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0034-25	Right Front Wheel Speed Sensor - Signal shape/waveform failure	Sensor signal shape / waveform failure Sensor short circuit to ground Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0034-2F	Right Front Wheel Speed Sensor - Signal erratic	Sensor signal erratic Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0034-31	Right Front Wheel Speed Sensor - No signal	No sensor signal Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0034-62	Right Front Wheel Speed Sensor - Signal compare failure	Sensor signal compare failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0034-64	Right Front Wheel Speed Sensor - Signal plausibility failure	Sensor signal plausibility failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C0036-38	Left Rear Tone Wheel - Signal frequency incorrect	Signal frequency incorrect Damaged ABS sensor ring	Check rear left wheel speed sensor ring for missing teeth or damage. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0037-14	Left Rear Wheel Speed Sensor - Circuit short to ground or open	Sensor short circuit to ground or open circuit Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C0037-25	Left Rear Wheel Speed Sensor - Signal shape/waveform failure	Sensor signal shape / waveform failure Sensor short circuit to ground Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0037-2F	Left Rear Wheel Speed Sensor - Signal erratic	Sensor signal erratic Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0037-31	Left Rear Wheel Speed Sensor - No signal	No sensor signal Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0037-62	Left Rear Wheel Speed Sensor - Signal compare failure	Sensor signal compare failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0037-64	Left Rear Wheel Speed Sensor - Signal plausibility failure	Sensor signal plausibility failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C0039-38	Right Rear Tone Wheel - Signal frequency incorrect	Signal frequency incorrect Damaged ABS sensor ring	Check rear right wheel speed sensor ring for missing teeth or damage. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C003A-14	Right Rear Wheel Speed Sensor - Circuit short to ground or open	Sensor short circuit to ground or open circuit Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C003A-25	Right Rear Wheel Speed Sensor - Signal shape/waveform failure	Sensor signal shape / waveform failure Sensor short circuit to ground Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C003A-2F	Right Rear Wheel Speed Sensor - Signal erratic	Sensor signal erratic Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C003A-31	Right Rear Wheel Speed Sensor - No signal	No sensor signal Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C003A-62	Right Rear Wheel Speed Sensor - Signal compare failure	Sensor signal compare failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C003A-64	Right Rear Wheel Speed Sensor - Signal plausibility failure	Sensor signal plausibility failure Sensor fault	Check the sensor lead and connector for damage. If damaged, renew the sensor. Refer to the electrical circuit diagrams and check the circuit between the sensor and the ABS module
C0051-28	Steering Wheel Position Sensor - Signal bias level out of range/zero adjustment failure	Signal bias level out of range/zero adjustment failure Incorrect angle sensor installed Wheel speed sensor wiring incorrectly wired across one axle Steering angle sensor fault	Check for a correctly installed steering angle sensor. Refer to the electrical circuit diagrams and check the circuit between the wheel speed sensors and the ABS module to ensure the sensors on one axle are correctly wired to the correct control module left or right pin outs. Renew the steering angle sensor. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle (not always in a straight line) for at least 9 seconds to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0051-67	Steering Wheel Position Sensor - Signal incorrect after event	Sensor signal incorrect after event Steering angle sensor fault Control module software error	Check for other DTCs that may aid diagnosis, especially in the steering angle sensor module. Renew the steering angle sensor. Clear the DTC and retest. If the problem persists, renew the ABS control module. Refer to the warranty policy and Procedures information if a module is suspect
C0062-28	Longitudinal Acceleration Sensor - Signal bias level out of range/zero adjustment failure	Sensor signal bias level out of range/zero adjustment failure Incorrectly installed sensor	Check installation and mounting of sensor cluster. Clear the DTC and retest, if problem persists renew the sensor. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0062-54	Longitudinal Acceleration Sensor - Missing calibration	Sensor missing calibration Incorrect sensor installed Incorrectly configured sensor	Ensure the correct sensor has been installed. Check mounting, connector and fuse of the sensor. Configure the sensor cluster using the manufacturers approved diagnostic system
C0062-64	Longitudinal Acceleration Sensor - Signal plausibility failure	Sensor signal plausibility failure Incorrectly installed sensor	Clear the DTC and retest. Check mounting, connector and fuse of the sensor. Configure the sensor cluster using the manufacturers approved diagnostic system
C0063-14	Yaw Rate Sensor - Circuit short to ground or open	Sensor circuit short to ground or open Sensor fault	The most likely cause of the fault is an open circuit on the harness. Refer to the electrical circuit diagrams and check the circuit between the sensor and the control module. Repair as necessary. Clear the DTC and retest. If the problem persists, renew the sensor
C0063-1C	Yaw Rate Sensor - Circuit voltage out of range	Sensor circuit voltage out of range	Refer to the electrical circuit diagrams and check the sensor power supply circuit
C0063-27	Yaw Rate Sensor - Signal rate of change above threshold	Sensor circuit power supply fuse failure Sensor insecurely mounted Sensor fault Control module software error	Refer to the electrical circuit diagrams and check the sensor power supply fuse. Check the yaw rate sensor connector condition. Ensure the sensor is correctly secured. If problem persists, renew the sensor. If the problem still persists, renew the ABS control module. Refer to the warranty policy and Procedures information if a module is suspect
C0063-28	Yaw Rate Sensor - Signal bias level out of range/zero adjustment failure	Sensor signal bias level out of range/zero adjustment failure Sensor insecurely mounted Sensor fault	Ensure the sensor is correctly secured. If problem persists, renew the sensor
C0063-41	Yaw Rate Sensor - General checksum failure	Sensor general checksum failure Sensor fault Control module fault	Renew the sensor. If the problem persists, renew the ABS control module. Refer to the warranty policy and Procedures information if a module is suspect
C0063-4A	Yaw Rate Sensor - Incorrect component installed	Incorrect sensor installed	Clear the DTC and retest. If the fault still exists renew the Yaw rate sensor with the suitable sensor cluster and repeat test cycle
C0063-49	Yaw Rate Sensor - Internal electronic failure	Sensor internal electronic failure	Clear the DTC and retest. If the problem persists, renew the sensor
C0063-64	Yaw Rate Sensor - Signal plausibility failure	Sensor signal plausibility failure The sensor value is not within the expected range compared to the steering angle sensor. Sensor insecurely mounted	NOTE: This DTC can be set if the vehicle is being tested on chassis dyno rollers. Ensure the sensor is correctly secured. Check that the steering angle sensor is correctly calibrated using the manufacturers recommended diagnostic system. If problem persists, renew the sensor. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 80kph (not always in a straight line) to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C0063-86	Yaw Rate Sensor - Signal invalid	Sensor signal invalid Incorrectly configured sensor	Clear the DTC and retest. If the problem persists, renew the sensor
C0063-95	Yaw Rate Sensor - Incorrect assembly	Sensor incorrect assembly/internal sensor fault	Ensure the correct sensor has been installed. Clear the DTC and retest. If the problem persists, renew the sensor. If the problem persists, renew the ABS control module. Refer to the warranty policy and Procedures information if a module is suspect
C0063-96	Yaw Rate Sensor - Component internal failure	Sensor power supply intermittent connection Sensor ground intermittent connection Sensor internal failure	Refer to the electrical circuit diagrams and check the sensor power supply and ground connections to the sensor. Check the sensor connector and ABS module for security and integrity (water ingress of damaged pins). If the problem persists, renew the yaw rate sensor. Calibrate the new sensor using the manufacturers approved diagnostic system. If the fault returns after an ignition cycle, renew the control module. Refer to the warranty policy and Procedures information if a module is suspect
C0064-64	Roll Rate Sensor - Signal plausibility failure	Sensor signal plausibility failure Sensor insecurely mounted	Ensure the sensor is correctly installed/secured. Clear DTC and Retest. If problem persists, renew the sensor
C006A-54	Multi-axis Acceleration Sensor - Missing calibration	Sensor missing calibration Serial number of yaw rate sensor saved in stored in control module memory does not match serial number of sensor Incorrect sensor installed Installed sensor not correctly calibrated	Check that the correct sensor has been installed. Configure the sensor cluster using the manufacturers approved diagnostic system. If calibration fails several times, renew the control module. Refer to the warranty policy and Procedures information if a module is suspect
C0072-4B	Brake Temperature Too High - Over temperature	Excessive use of brakes Excessive use of traction control system	This DTC is for information only. Clear the DTC
C101F-49	Generic Valve Failure - Internal electronic failure	ABS modulator internal fault	Renew the control module. Refer to the warranty policy and Procedures information if a module is suspect
C1109-24	Vehicle Dynamics Control Switch - Signal stuck high	Signal stuck high - DSC Switch operation fault If the DSC switch is pressed for longer than 1 minute, the switch is deemed to be malfunctioning	Check the switch operation. Refer to the electrical circuit diagrams and check the DSC switch and circuits. Check and install a new DSC switch as required
C1A77-16	Valve Relay Supply Circuit - Circuit voltage below threshold	Circuit voltage below threshold Fuse Harness/connector damaged	Refer to the electrical circuit diagrams and check the harness connection and fuse to the valve relay circuits
C1A90-12	Wheel Speed Sensor Supply - Circuit short to battery	Wheel speed sensor supply circuit short circuit to power	Refer to the electrical circuit diagrams and check the wheel speed sensor power supply line circuits between the sensors and the control module
C1A95-4A	Wheel Speed Sensor - Incorrect component installed	The incorrect wheel speed sensor has been installed	Check the correct wheel speed sensors are installed. Clear the DTC and retest
C1A95-64	Wheel Speed Sensor - Signal plausibility failure	Signal plausibility failure Wheel speed sensor fault (any) Sensor ring damaged, incorrect or defective Harness fault Incorrect wheel/tire assembly size	Check for correct wheel/tire sizes. Check the wheel speed sensors and circuits for damage. Remove the sensor and visually inspect the sensor ring on the constant velocity joint (CVJ) for missing or damaged teeth. If the sensor ring is damaged, renew the CVJ. Use an oscilloscope to examine the signals from all wheel speed sensors for abnormal high frequencies (modulation and peak signals). Renew sensors as necessary. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph for at least 30 seconds to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C1A96-64	Brake Light Switch - Signal plausibility failure	Signal plausibility failure Stop lamp switch fault Harness/connector issue	Check the Stop lamp function. Ensure the brake lamp switch is correctly installed and configured. Refer to the electrical circuit diagrams and check the stop lamp switch circuit, rectify as necessary. Check the engine control module for DTCs. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph with at least one brake pedal press to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C1A97-24	Lateral Accelerometer - Signal stuck high	Signal stuck high Yaw rate/lateral acceleration sensor internal error	Renew the combined lateral acceleration/yaw rate sensor
C1A98-96	Yaw Rate Sensor - Component internal failure	Incorrect assembly Sensor installation incorrect Yaw rate/lateral acceleration sensor internal error	Check the combined lateral acceleration/yaw rate sensor installation and orientation. Check mounting, connector and fuse of the sensor. Clear the DTC and retest. If the problem persists, renew the combined lateral acceleration/yaw rate sensor
C1A98-2F	Yaw Rate Sensor - Signal erratic	Yaw rate sensor signal fault for 2 minutes	Information only, regard as normal operation. Clear the DTC, cycle the ignition and retest. If the fault reoccurs, renew the combined lateral acceleration/yaw rate sensor. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C1B00-29	Steering Angle Sensor - Signal invalid	Sensor signal invalid Sensor installation incorrect steering angle sensor fault	Check steering angle sensor module for DTCs. Check the steering angle sensor installation and orientation. Clear the DTC and retest. If the problem persists, renew the sensor
C1B00-49	Steering Angle Sensor - Internal electronic failure	Sensor internal electronic failure	Check steering angle sensor module for DTCs. Renew the sensor
C1B00-64	Steering Angle Sensor - Signal plausibility failure	Sensor signal plausibility failure Sensor installation incorrect steering angle sensor fault Yaw rate sensor installation incorrect	Check steering angle sensor module for DTCs. Check the steering angle sensor installation and orientation. Check the yaw rate sensor installation and orientation. Clear the DTC and retest. If the problem persists, renew the steering angle sensor
C1B00-92	Steering Angle Sensor - Performance or incorrect operation	Sensor performance or incorrect operation Sensor installation incorrect steering angle sensor fault	Check steering angle sensor module for DTCs. Check the steering angle sensor installation and orientation. Check the yaw rate sensor installation and orientation. Clear the DTC and retest. If the problem persists, renew the steering angle sensor
C1B02-16	Return Pump - Circuit voltage below threshold	Return pump circuit voltage below threshold Harness damaged Defective fuse	Refer to the electrical circuit diagrams and check the circuit, fuses and the connection to the ABS module. Rectify as necessary. After rectification, either clear the DTCs and cycle the ignition or cycle the ignition and drive the vehicle above 15kph to ensure the lamps extinguish. When cycling the ignition, allow sufficient time for the 'P' symbol illumination to extinguish on the gear shifter (if installed) before returning the ignition state to on
C1B02-49	Return Pump - Internal electronic failure	ABS control module internal electronic failure	Renew the ABS modulator. Refer to the warranty policy and Procedures information if a module is suspect
C1B22-24	Hill Descent Switch - Signal stuck high	Signal stuck high If the HDC switch is pressed for longer than 1 minute, this DTC may be logged. Harness/connector issue	Check the switch operation. Refer to the electrical circuit diagrams and check the switch and circuit for short to power
C2009-64	Front Axle Wheel Speed Sensors Swapped - Signal plausibility failure	Sensor location swapped	Swap the front wheel speed sensor locations. Clear the DTC and retest. In order to clear the DTC/warning lamp after fault is rectified, the vehicle must be driven above 15km/h
C200A-64	Rear Axle Wheel Speed Sensors Swapped - Signal plausibility failure	Sensor location swapped	Swap the rear wheel speed sensor locations. Clear the DTC and retest. In order to clear the DTC/warning lamp after fault is rectified, the vehicle must be driven above 15km/h
U0001-88	High Speed CAN Communication Bus - Bus off	Bus off	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network
U0074-88	Control Module Communication Bus "B" Off - Bus off	CAN Bus off	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network
U0100-00	Lost Communication With ECM/PCM "A" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and traction control module
U0101-00	Lost Communication With TCM - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the transmission control module and traction control module
U0102-00	Lost Communication With Transfer Case Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the transfer case control module and traction control module
U0103-00	Lost Communication With Gear Shift Control Module A - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the gear shift control module and traction control module
U0104-00	Lost Communication With Cruise Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the cruise control module and traction control module
U0123-00	Lost Communication With Yaw Rate Sensor Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the yaw rate sensor control module and traction control module
U0126-00	Lost Communication With Steering Angle Sensor Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the steering angle sensor module and traction control module
U0128-00	Lost Communication With Park Brake Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the park brake control module and traction control module
U0132-00	Lost Communication With Suspension Control Module "A" - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the suspension control module and traction control module
U0133-00	Lost Communication With Active Roll Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the active roll control module and traction control module
U0136-00	Lost Communication With Differential Control Module - Rear - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the differential control module and traction control module
U0138-00	Lost Communication With All Terrain Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the all terrain control module and traction control module
U0140-00	Lost Communication With Body Control Module - No sub type information	No sub type information	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Central Junction Box and traction control module
U0300-00	Internal Control Module Software Incompatibility - No sub type information	Control module has been installed to the incorrect vehicle	Ensure the correct module is installed
U0401-68	Invalid Data Received from ECM/PCM A - Event information	Invalid data received	Check the engine control module for related DTCs and refer to the relevant DTC index
U0402-68	Invalid Data Received from TCM - Event information	Invalid data received	Check the transmission control module for related DTCs and refer to the relevant DTC index
U0403-68	Invalid Data Received From Transfer Case Control Module - Event information	Invalid data received	Check the transfer case control module for related DTCs and refer to the relevant DTC index
U0405-68	Invalid Data Received From Cruise Control Module - Event information	Invalid data received	Check the cruise control module for related DTCs and refer to the relevant DTC index
U0417-68	Invalid Data Received From Park Brake Control Module - Event information	Invalid data received	Check the park brake control module for related DTCs and refer to the relevant DTC index
U0421-68	Invalid Data Received from Suspension Control Module A - Event information	Invalid data received	Check the suspension control module for related DTCs and refer to the relevant DTC index
U0428-68	Invalid Data Received From Steering Angle Sensor Module - Event information	Invalid data received	Check the steering angle sensor control module for related DTCs and refer to the relevant DTC index
U0437-68	Invalid Data Received From Differential Control Module-Rear - Event information	Invalid data received	Check the differential control module for related DTCs and refer to the relevant DTC index
U0439-68	Invalid Data Received From All Terrain Control Module - Event information	Invalid data received	Check the all terrain control module for related DTCs and refer to the relevant DTC index
U1A14-00	CAN Initialization Failure - No sub type information	Incorrect control module installed to vehicle	Check that the correct ABS module has been installed. Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network
U2101-00	Control Module Configuration Incompatible - No sub type information	Car configuration file incorrectly configured Vehicle variant code value not supported in this project variant code value not released in this project variant code value out of range	Configure the car configuration file using the manufacturers approved diagnostic system
U2101-68	Control Module Configuration Incompatible - Event information	Vehicle variant code distributed via CAN is not matching the code stored in the Central Junction Box memory ABS module has been installed from another vehicle (codes do not match expected) New ABS module has been installed and at first use code did not match (becomes historic after first use)	Check that the correct ABS module has been installed. Configure the car configuration file using the manufacturers approved diagnostic system
U3000-00	Control Module - No sub type information	Incorrect control module installed to vehicle	Check that the correct ABS module has been installed. Refer to the electrical circuit diagrams and check the power and ground circuits to the component. Configure the module(s) using the manufacturers approved diagnostic system. Refer to the warranty policy and Procedures information if a module is suspect. Refer to the Network Communications instructions of the workshop information
U3000-45	Control Module - Program memory failure	Program memory failure (software error)	Clear the DTC and retest. Repeat for several times. If the problem persists, renew the ABS control module. Refer to the warranty policy and Procedures information if a module is suspect
U3000-49	Control Module - Internal electronic failure	Internal electronic failure	Renew the ABS control module. Refer to the warranty policy and Procedures information if a module is suspect
U3000-4B	Control Module - Over temperature	Module over temperature has been detected Excessive ABS interaction has been invoked, possibly by diagnostic equipment	Allow the unit to cool, clear the DTC and retest. If the problem persists, as a last resort renew the ABS control module. Consider environmental conditions before suspecting the module. Refer to the warranty policy and Procedures information if a module is suspect
U3000-53	Control Module - De-activated	Deactivated during software download to other modules on vehicle	This is not a fault. ECU temporarily deactivated following programming session. Please cycle the ignition to clear
U3000-68	Control Module - Event information	Stability assist operation is in progress and this has been continuing for an unfeasible length of time	Check for other related DTCs. Check the wheel speed sensors, combined yaw rate/lat Acc sensor and steering angle sensor
U3000-87	Control Module - Missing message	Car configuration file missing message	Configure the car configuration file using the manufacturers approved diagnostic system
U3002-81	Vehicle Identification Number - Invalid serial data received	Invalid vehicle identification number	Configure the car configuration file using the manufacturers approved diagnostic system
U3003-62	Battery Voltage - Signal compare failure	Signal compare failure	Check the battery condition and state of charge. Check the vehicle charging system. Refer to the relevant workshop information
U3006-16	Control Module Input Power "A" - Circuit voltage below threshold	ABS control module circuit voltage below threshold Battery voltage low Battery ground cable: high resistance Battery connections loose/corroded Battery current drain	Refer to the electrical circuit diagrams and check the module power and ground circuits. Check the battery condition and state of charge. Check the vehicle charging system. Refer to the relevant workshop information
U3006-17	Control Module Input Power "A" - Circuit voltage above threshold	ABS control module circuit voltage above threshold Charging system fault	Check the battery condition and state of charge. Check the vehicle charging system. Refer to the relevant workshop information
U3006-1C	Control Module Input Power "A" - Circuit voltage out of range	ABS control module circuit voltage out of range, a momentary low voltage occurred	Check the battery condition and state of charge. Check the vehicle charging system. Check the connector security to the module. Refer to the relevant workshop information