Restraints Control Module (RCM)

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT ONE MINUTE. FAILURE TO FOLLOW THIS INSTRUCTION MAY RESULT IN PERSONAL INJURY.

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being checked and/or the donor vehicle.

NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before the replacement of a component.

NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).

NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance always take the resistance of the DMM leads into account.

NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.

Description And Operation

For a detailed description of the restraints control system, refer to the relevant Description and Operation. Refer to Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) and Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) .

RESTRAINTS CONTROL MODULE (RCM)

DTC	Description	Possible Cause	Action
B0001-11	Driver Frontal Stage 1 Deployment Control - Circuit short to ground	Driver airbag (stage 1) circuit short circuit to ground	Refer to electrical circuit diagrams and check driver's airbag ignitor (stage 1) circuit for short circuit to ground
B0001-12	Driver Frontal Stage 1 Deployment Control - Circuit short to battery	Driver airbag (stage 1) circuit short circuit to power	Refer to electrical circuit diagrams and check driver's airbag ignitor (stage 1) circuit for short circuit to power
B0001-13	Driver Frontal Stage 1 Deployment Control - Circuit open	Driver's airbag ignitor stage 1 circuit open circuit	Refer to electrical circuit diagrams and check driver's airbag ignitor (stage 1) circuit for open circuit
B0001-19	Driver Frontal Stage 1 Deployment Control - Circuit current above threshold	Driver airbag (stage 1) circuit short circuit	Refer to the electrical circuit diagrams and test the driver airbag (stage 1) circuit for short circuit
B0001-1A	Driver Frontal Stage 1 Deployment Control - Circuit resistance below threshold	Driver's airbag ignitor stage 1 circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver airbag (stage 1) circuit for short circuit between both lines to the ignitor
B0001-95	Driver Frontal Stage 1 Deployment Control - Incorrect assembly	Driver's airbag ignitor (stage 1) incorrect assembly	Check driver's airbag ignitor (stage 1) installed correctly Using the manufacturer approved diagnostic system check and up-date the car configuration file as required
B0002-11	Driver Frontal Stage 2 Deployment Control - Circuit short to ground	Driver airbag (stage 2) circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver airbag (stage 2) circuit for short circuit to ground
B0002-12	Driver Frontal Stage 2 Deployment Control - Circuit short to battery	Driver's airbag ignitor (stage 2) circuit short circuit to power	Refer to the electrical circuit diagrams and check driver's airbag ignitor (stage 2) circuit for short circuit to power
B0002-13	Driver Frontal Stage 2 Deployment Control - Circuit open	Driver's airbag ignitor stage 2 circuit open circuit	Refer to electrical circuit diagrams and check driver's airbag ignitor (stage 2) circuit for open circuit
B0002-19	Driver Frontal Stage 2 Deployment Control - Circuit current above threshold	Driver airbag (stage 2) circuit short circuit	Refer to the electrical circuit diagrams and test the driver airbag (stage 2) circuit for short circuit
B0002-1A	Driver Frontal Stage 2 Deployment Control - Circuit resistance below threshold	Driver's airbag ignitor stage 2 circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver airbag (stage 2) circuit for short circuit between both lines to the ignitor
B0002-95	Driver Frontal Stage 2 Deployment Control - Incorrect assembly	Driver's airbag ignitor (stage 2) incorrect assembly	Check driver's airbag ignitor (stage 2) installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0004-11	Driver Knee Bolster Deployment Control - Circuit short to ground	NOTE: Circuit reference KNEE AIRBAG DRIVER+ / KNEE AIRBAG DRIVER- Driver lower airbag circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver lower airbag circuit for short circuit to ground
B0004-12	Driver Knee Bolster Deployment Control - Circuit short to battery	NOTE: Circuit reference KNEE AIRBAG DRIVER+ / KNEE AIRBAG DRIVER- Driver lower airbag circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver lower airbag circuit for short circuit to power
B0004-13	Driver Knee Bolster Deployment Control - Circuit open	NOTE: Circuit reference KNEE AIRBAG DRIVER+ / KNEE AIRBAG DRIVER- Driver lower airbag circuit open circuit	Refer to the electrical circuit diagrams and test the driver lower airbag circuit for open circuit
B0004-19	Driver Knee Bolster Deployment Control - Circuit current above threshold	NOTE: Circuit reference KNEE AIRBAG DRIVER+ / KNEE AIRBAG DRIVER- Driver lower airbag circuit short circuit	Refer to the electrical circuit diagrams and test the driver lower airbag circuit for short circuit
B0004-1A	Driver Knee Bolster Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference KNEE AIRBAG DRIVER+ / KNEE AIRBAG DRIVER- Driver lower airbag circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver lower airbag circuit for short circuit between both lines to the ignitor
B0004-95	Driver Knee Bolster Deployment Control - Incorrect assembly	NOTE: Circuit reference KNEE AIRBAG DRIVER+ / KNEE AIRBAG DRIVER- Driver's knee bolster ignitor incorrect assembly	Check that the driver lower airbag is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0005-11	Collapsible Steering Column Deployment Control - Circuit short to ground	NOTE: Circuit reference STEERING COLUMN+ / STEERING COLUMN- Steering column collapse actuator circuit short circuit to ground	Refer to the electrical circuit diagrams and test the steering column collapse actuator circuit for short circuit to ground
B0005-12	Collapsible Steering Column Deployment Control - Circuit short to battery	NOTE: Circuit reference STEERING COLUMN+ / STEERING COLUMN- Steering column collapse actuator circuit short circuit to power	Refer to the electrical circuit diagrams and test the steering column collapse actuator circuit for short circuit to power
B0005-13	Collapsible Steering Column Deployment Control - Circuit open	NOTE: Circuit reference STEERING COLUMN+ / STEERING COLUMN- Steering column collapse actuator circuit open circuit	Refer to the electrical circuit diagrams and test the steering column collapse actuator circuit for open circuit
B0005-19	Collapsible Steering Column Deployment Control - Circuit current above threshold	NOTE: Circuit reference STEERING COLUMN+ / STEERING COLUMN- Steering column collapse actuator circuit short circuit	Refer to the electrical circuit diagrams and test the steering column collapse actuator circuit for short circuit
B0005-1A	Collapsible Steering Column Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference STEERING COLUMN+ / STEERING COLUMN- Steering column collapse actuator circuit resistance below threshold	Refer to the electrical circuit diagrams and test the steering column collapse actuator circuit for short circuit between both lines to the deployable device
B0005-95	Collapsible Steering Column Deployment Control - Incorrect assembly	NOTE: Circuit reference STEERING COLUMN+ / STEERING COLUMN- Steering column collapse actuator incorrect assembly	Check that the steering column collapse actuator is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0010-11	Passenger Frontal Stage 1 Deployment Control - Circuit short to ground	NOTE: Circuit reference AIRBAG STAGE 1 PASS+ / AIRBAG STAGE 1 PASS- Passenger airbag (stage 1) circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger airbag (stage 1) circuit for short circuit to ground
B0010-12	Passenger Frontal Stage 1 Deployment Control - Circuit short to battery	NOTE: Circuit reference AIRBAG STAGE 1 PASS+ / AIRBAG STAGE 1 PASS- Passenger airbag (stage 1) circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger airbag (stage 1) circuit for short circuit to power
B0010-13	Passenger Frontal Stage 1 Deployment Control - Circuit open	NOTE: Circuit reference AIRBAG STAGE 1 PASS+ / AIRBAG STAGE 1 PASS- Passenger airbag (stage 1) circuit open circuit	Refer to the electrical circuit diagrams and test the passenger airbag (stage 1) circuit for open circuit
B0010-19	Passenger Frontal Stage 1 Deployment Control - Circuit current above threshold	NOTE: Circuit reference AIRBAG STAGE 1 PASS+ / AIRBAG STAGE 1 PASS- Passenger airbag (stage 1) circuit short circuit	Refer to the electrical circuit diagrams and test the passenger airbag (stage 1) circuit for short circuit
B0010-1A	Passenger Frontal Stage 1 Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference AIRBAG STAGE 1 PASS+ / AIRBAG STAGE 1 PASS- Passenger airbag (stage 1) circuit resistance below threshold	Refer to the electrical circuit diagrams and test the passenger airbag (stage 1) circuit for short circuit between both lines to the ignitor
B0010-95	Passenger Frontal Stage 1 Deployment Control - Incorrect assembly	NOTE: Circuit reference AIRBAG STAGE 1 PASS+ / AIRBAG STAGE 1 PASS- Passenger airbag (stage 1) incorrect assembly	Check that the passenger airbag (stage 1) is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0011-11	Passenger Frontal Stage 2 Deployment Control - Circuit short to ground	NOTE: Circuit reference AIRBAG STAGE 2 PASS+ / AIRBAG STAGE 2 PASS- Passenger airbag (stage 2) circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger airbag (stage 2) circuit for short circuit to ground
B0011-12	Passenger Frontal Stage 2 Deployment Control - Circuit short to battery	NOTE: Circuit reference AIRBAG STAGE 2 PASS+ / AIRBAG STAGE 2 PASS- Passenger airbag (stage 2) circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger airbag (stage 2) circuit for short circuit to power
B0011-13	Passenger Frontal Stage 2 Deployment Control - Circuit open	NOTE: Circuit reference AIRBAG STAGE 2 PASS+ / AIRBAG STAGE 2 PASS- Passenger airbag (stage 2) circuit open circuit	Refer to the electrical circuit diagrams and test the passenger airbag (stage 2) circuit for open circuit
B0011-19	Passenger Frontal Stage 2 Deployment Control - Circuit current above threshold	NOTE: Circuit reference AIRBAG STAGE 2 PASS+ / AIRBAG STAGE 2 PASS- Passenger airbag (stage 2) circuit short circuit	Refer to the electrical circuit diagrams and test the passenger airbag (stage 2) circuit for short circuit
B0011-1A	Passenger Frontal Stage 2 Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference AIRBAG STAGE 2 PASS+ / AIRBAG STAGE 2 PASS- Passenger airbag (stage 2) circuit resistance below threshold	Refer to the electrical circuit diagrams and test the passenger airbag (stage 2) circuit for short circuit between both lines to the ignitor
B0011-95	Passenger Frontal Stage 2 Deployment Control - Incorrect assembly	NOTE: Circuit reference AIRBAG STAGE 2 PASS+ / AIRBAG STAGE 2 PASS- Passenger airbag (stage 2) incorrect assembly	Check that the passenger airbag (stage 2) is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0050-11	Driver Seatbelt Sensor - Circuit short to ground	NOTE: Circuit Reference BELT LOCK DRIVER Driver safety belt buckle switch circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver safety belt buckle switch circuit for short circuit to ground
B0050-12	Driver Seatbelt Sensor - Circuit short to battery	NOTE: Circuit Reference BELT LOCK DRIVER Driver safety belt buckle switch circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver safety belt buckle switch circuit for short circuit to power
B0050-13	Driver Seatbelt Sensor - Circuit open	NOTE: Circuit Reference BELT LOCK DRIVER Driver safety belt buckle switch circuit open circuit	Refer to the electrical circuit diagrams and test the driver safety belt buckle switch circuit for open circuit
B0050-19	Driver Seatbelt Sensor - Circuit current above threshold	NOTE: Circuit Reference BELT LOCK DRIVER Driver safety belt buckle switch circuit short circuit	Refer to the electrical circuit diagrams and test the driver safety belt buckle switch circuit for short circuit
B0050-1E	Driver Seatbelt Sensor - Circuit resistance out of range	NOTE: Circuit Reference BELT LOCK DRIVER Driver safety belt buckle switch circuit resistance out of range	Refer to the electrical circuit diagrams and test the driver safety belt buckle switch for resistance out of range
B0050-95	Driver Seatbelt Sensor - Incorrect assembly	NOTE: Circuit Reference BELT LOCK DRIVER Driver safety belt buckle switch incorrect assembly	Check that the driver safety belt buckle switch is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0052-11	Passenger Seatbelt Sensor - Circuit short to ground	NOTE: Circuit reference BELT LOCK PASS Passenger safety belt buckle switch circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger safety belt buckle switch circuit for short circuit to ground
B0052-12	Passenger Seatbelt Sensor - Circuit short to battery	NOTE: Circuit reference BELT LOCK PASS Passenger safety belt buckle switch circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger safety belt buckle switch circuit for short circuit to power
B0052-13	Passenger Seatbelt Sensor - Circuit open	NOTE: Circuit reference BELT LOCK PASS Passenger safety belt buckle switch circuit open circuit	Refer to the electrical circuit diagrams and test the passenger safety belt buckle switch circuit for open circuit
B0052-19	Passenger Seatbelt Sensor - Circuit current above threshold	NOTE: Circuit reference BELT LOCK PASS Passenger safety belt buckle switch circuit short circuit	Refer to the electrical circuit diagrams and test the passenger safety belt buckle switch circuit for short circuit
B0052-1E	Passenger Seatbelt Sensor - Circuit resistance out of range	NOTE: Circuit reference BELT LOCK PASS Passenger safety belt buckle switch circuit resistance out of range	Refer to the electrical circuit diagrams and test the passenger safety belt buckle switch for resistance out of range
B0052-95	Passenger Seatbelt Sensor - Incorrect assembly	NOTE: Circuit reference BELT LOCK PASS Passenger safety belt buckle switch incorrect assembly	Check that the passenger safety belt buckle switch is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0070-11	Driver Seatbelt Pretensioner Deployment Control - Circuit short to ground	NOTE: Circuit reference PRETENSIONER DRIVER+ / PRETENSIONER DRIVER- Driver safety belt pretensioner circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver safety belt pretensioner circuit for short circuit to ground
B0070-12	Driver Seatbelt Pretensioner Deployment Control - Circuit short to battery	NOTE: Circuit reference PRETENSIONER DRIVER+ / PRETENSIONER DRIVER- Driver safety belt pretensioner circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver safety belt pretensioner circuit for short circuit to power
B0070-13	Driver Seatbelt Pretensioner Deployment Control - Circuit open	NOTE: Circuit reference PRETENSIONER DRIVER+ / PRETENSIONER DRIVER- Driver safety belt pretensioner circuit open circuit	Refer to the electrical circuit diagrams and test the driver safety belt pretensioner circuit for open circuit
B0070-19	Driver Seatbelt Pretensioner Deployment Control - Circuit current above threshold	NOTE: Circuit reference PRETENSIONER DRIVER+ / PRETENSIONER DRIVER- Driver safety belt pretensioner circuit short circuit	Refer to the electrical circuit diagrams and test the driver safety belt pretensioner circuit for short circuit
B0070-1A	Driver Seatbelt Pretensioner Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference PRETENSIONER DRIVER+ / PRETENSIONER DRIVER- Driver safety belt pretensioner circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver safety belt pretensioner circuit for short circuit between both lines to the ignitor
B0070-95	Driver Seatbelt Pretensioner Deployment Control - Incorrect assembly	NOTE: Circuit reference PRETENSIONER DRIVER+ / PRETENSIONER DRIVER- Driver safety belt pretensioner incorrect assembly	Check that the driver safety belt pretensioner is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0072-11	Passenger Seatbelt Pretensioner Deployment Control - Circuit short to ground	NOTE: Circuit reference PRETENSIONER PASS+ / PRETENSIONER PASS- Passenger safety belt pretensioner circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger safety belt pretensioner circuit for short circuit to ground
B0072-12	Passenger Seatbelt Pretensioner Deployment Control - Circuit short to battery	NOTE: Circuit reference PRETENSIONER PASS+ / PRETENSIONER PASS- Passenger safety belt pretensioner circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger safety belt pretensioner circuit for short circuit to power
B0072-13	Passenger Seatbelt Pretensioner Deployment Control - Circuit open	NOTE: Circuit reference PRETENSIONER PASS+ / PRETENSIONER PASS- Passenger safety belt pretensioner circuit open circuit	Refer to the electrical circuit diagrams and test the passenger safety belt pretensioner circuit for open circuit
B0072-19	Passenger Seatbelt Pretensioner Deployment Control - Circuit current above threshold	NOTE: Circuit reference PRETENSIONER PASS+ / PRETENSIONER PASS- Passenger safety belt pretensioner circuit short circuit	Refer to the electrical circuit diagrams and test the passenger safety belt pretensioner circuit for short circuit
B0072-1A	Passenger Seatbelt Pretensioner Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference PRETENSIONER PASS+ / PRETENSIONER PASS- Passenger safety belt pretensioner circuit resistance below threshold	Refer to the electrical circuit diagrams and test the passenger safety belt pretensioner circuit for short circuit between both lines to the ignitor
B0072-95	Passenger Seatbelt Pretensioner Deployment Control - Incorrect assembly	NOTE: Circuit reference PRETENSIONER PASS+ / PRETENSIONER PASS- Passenger safety belt pretensioner incorrect assembly	Check that the passenger safety belt pretensioner is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0080-11	Driver Seatbelt Load Limiter Deployment Control - Circuit short to ground	NOTE: Circuit reference RETRACTOR DRIVER+ / RETRACTOR DRIVER- Driver safety belt retractor and pretensioner circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver safety belt retractor and pretensioner circuit for short circuit to ground
B0080-12	Driver Seatbelt Load Limiter Deployment Control - Circuit short to battery	NOTE: Circuit reference RETRACTOR DRIVER+ / RETRACTOR DRIVER- Driver safety belt retractor and pretensioner circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver safety belt retractor and pretensioner circuit for short circuit to power
B0080-13	Driver Seatbelt Load Limiter Deployment Control - Circuit open	NOTE: Circuit reference RETRACTOR DRIVER+ / RETRACTOR DRIVER- Driver safety belt retractor and pretensioner circuit open circuit	Refer to the electrical circuit diagrams and test the driver safety belt retractor and pretensioner circuit for open circuit
B0080-19	Driver Seatbelt Load Limiter Deployment Control - Circuit current above threshold	NOTE: Circuit reference RETRACTOR DRIVER+ / RETRACTOR DRIVER- Driver safety belt retractor and pretensioner circuit short circuit	Refer to the electrical circuit diagrams and test the driver safety belt retractor and pretensioner circuit for short circuit
B0080-1A	Driver Seatbelt Load Limiter Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference RETRACTOR DRIVER+ / RETRACTOR DRIVER- Driver safety belt retractor and pretensioner circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver safety belt retractor and pretensioner circuit for short circuit between both lines to the ignitor
B0080-95	Driver Seatbelt Load Limiter Deployment Control - Incorrect assembly	NOTE: Circuit reference RETRACTOR DRIVER+ / RETRACTOR DRIVER- Driver safety belt retractor and pretensioner incorrect assembly	Check that the driver safety belt retractor and pretensioner is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B0082-11	Passenger Seatbelt Load Limiter Deployment Control - Circuit short to ground	NOTE: Circuit reference RETRACTOR PASS+ / RETRACTOR PASS- Passenger safety belt retractor and pretensioner circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger safety belt retractor and pretensioner circuit for short circuit to ground
B0082-12	Passenger Seatbelt Load Limiter Deployment Control - Circuit short to battery	NOTE: Circuit reference RETRACTOR PASS+ / RETRACTOR PASS- Passenger safety belt retractor and pretensioner circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger safety belt retractor and pretensioner circuit for short circuit to power
B0082-13	Passenger Seatbelt Load Limiter Deployment Control - Circuit open	NOTE: Circuit reference RETRACTOR PASS+ / RETRACTOR PASS- Passenger safety belt retractor and pretensioner circuit open circuit	Refer to the electrical circuit diagrams and test the passenger safety belt retractor and pretensioner circuit for open circuit
B0082-19	Passenger Seatbelt Load Limiter Deployment Control - Circuit current above threshold	NOTE: Circuit reference RETRACTOR PASS+ / RETRACTOR PASS- Passenger safety belt retractor and pretensioner circuit short circuit	Refer to the electrical circuit diagrams and test the passenger safety belt retractor and pretensioner circuit for short circuit
B0082-1A	Passenger Seatbelt Load Limiter Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference RETRACTOR PASS+ / RETRACTOR PASS- Passenger safety belt retractor and pretensioner circuit resistance below threshold	Refer to the electrical circuit diagrams and test the passenger safety belt retractor and pretensioner circuit for short circuit between both lines to the ignitor
B0082-95	Passenger Seatbelt Load Limiter Deployment Control - Incorrect assembly	NOTE: Circuit reference RETRACTOR PASS+ / RETRACTOR PASS- Passenger safety belt retractor and pretensioner incorrect assembly	Check that the passenger safety belt retractor and pretensioner is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B00B5-11	Driver Seat Track Position Restraints Sensor - Circuit short to ground	NOTE: Circuit reference DRIVER SEAT TRACK Driver seat track position sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver seat track position sensor circuit for short circuit to ground
B00B5-12	Driver Seat Track Position Restraints Sensor - Circuit short to battery	NOTE: Circuit reference DRIVER SEAT TRACK Driver seat track position sensor circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver seat track position sensor circuit for short circuit to power
B00B5-13	Driver Seat Track Position Restraints Sensor - Circuit open	NOTE: Circuit reference DRIVER SEAT TRACK Driver seat track position sensor circuit open circuit	Refer to the electrical circuit diagrams and test the driver seat track position sensor circuit for open circuit
B00B5-19	Driver Seat Track Position Restraints Sensor - Circuit current above threshold	NOTE: Circuit reference DRIVER SEAT TRACK Driver seat track position sensor circuit short circuit	Refer to the electrical circuit diagrams and test the driver seat track position sensor circuit for short circuit
B00B5-1E	Driver Seat Track Position Restraints Sensor - Circuit resistance out of range	NOTE: Circuit reference DRIVER SEAT TRACK Driver seat track position sensor circuit resistance out of range	Refer to the electrical circuit diagrams and test the driver seat track position sensor for resistance out of range
B00B5-95	Driver Seat Track Position Restraints Sensor - Incorrect assembly	NOTE: Circuit reference DRIVER SEAT TRACK Driver seat track position sensor incorrect assembly	Check that the driver seat track position sensor is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B00D2-68	Restraint System Malfunction Indicator 1 - Event information	Restraint system events information	Refer to the electrical circuit diagrams and test the instrument cluster for internal fault
B00D2-95	Restraint System Malfunction Indicator 1 - Incorrect assembly	Restraint system incorrect assembly	Using the manufacturer approved diagnostic system check and install latest relevant level of software to the restraints control module Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B00D5-12	Restraint System Passenger Disable Indicator - Circuit short to battery	NOTE: Circuit reference PAD INDICATOR Passenger airbag deactivation lamp circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger airbag deactivation lamp circuit for short circuit to power
B00D5-14	Restraint System Passenger Disable Indicator - Circuit short to ground or open	NOTE: Circuit reference PAD INDICATOR Passenger airbag deactivation lamp circuit short circuit to ground, open circuit, high resistance	Refer to the electrical circuit diagrams and test the passenger airbag deactivation lamp circuit for short circuit to ground, open circuit, high resistance
B00D5-95	Restraint System Passenger Disable Indicator - Incorrect assembly	NOTE: Circuit reference PAD INDICATOR Passenger airbag deactivation lamp incorrect assembly	Check that the passenger airbag deactivation lamp is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B00DF-24	Passenger Restraints Disable Switch - Signal stuck high	Passenger airbag deactivation switch stuck or internal failure	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch
B00DF-55	Passenger Restraints Disable Switch - Not configured	Passenger airbag deactivation switch not configured	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch
B00DF-64	Passenger Restraints Disable Switch - Signal plausibility failure	Passenger airbag deactivation switch configuration error	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch
B10FD-11	Drivers Side Peripheral Acceleration Sensor - Circuit short to ground	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver side impact sensor 1 circuit for short circuit to ground
B10FD-12	Drivers Side Peripheral Acceleration Sensor - Circuit short to battery	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver side impact sensor 1 circuit for short circuit to power
B10FD-19	Drivers Side Peripheral Acceleration Sensor - Circuit current above threshold	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 circuit short circuit	Refer to the electrical circuit diagrams and test the driver side impact sensor 1 circuit for short circuit
B10FD-4A	Drivers Side Peripheral Acceleration Sensor - Incorrect component installed	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 incorrect component installed	Restraints control module detected a mis-match between the hardware fitted and what is expected Check that the correct driver side impact sensor 1 is installed
B10FD-87	Drivers Side Peripheral Acceleration Sensor - Missing message	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 circuit open circuit Driver side impact sensor internal fault	Refer to the electrical circuit diagrams and test the driver side impact sensor 1 circuit for communication fault
B10FD-95	Drivers Side Peripheral Acceleration Sensor - Incorrect assembly	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 incorrect assembly	Check that the driver side impact sensor 1 is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B10FD-96	Drivers Side Peripheral Acceleration Sensor - Component internal failure	NOTE: Circuit reference SENSOR-ACCEL DRIV 1+ / SENSOR-ACCEL DRIV 1- Driver side impact sensor 1 internal fault	Refer to the electrical circuit diagrams and test the driver side impact sensor 1
B10FE-11	Passenger Side Peripheral Acceleration Sensor - Circuit short to ground	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger side impact sensor 1 circuit for short circuit to ground
B10FE-12	Passenger Side Peripheral Acceleration Sensor - Circuit short to battery	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger side impact sensor 1 circuit for short circuit to power
B10FE-19	Passenger Side Peripheral Acceleration Sensor - Circuit current above threshold	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 circuit short circuit	Refer to the electrical circuit diagrams and test the passenger side impact sensor 1 circuit for short circuit
B10FE-4A	Passenger Side Peripheral Acceleration Sensor - Incorrect component installed	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 incorrect component installed	Restraints control module detected a mis-match between the hardware fitted and what is expected Check that the correct passenger side impact sensor 1 is installed
B10FE-87	Passenger Side Peripheral Acceleration Sensor - Missing message	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 circuit open circuit Passenger side impact sensor 1 internal fault	Refer to the electrical circuit diagrams and test the passenger side impact sensor 1 circuit for communication fault
B10FE-95	Passenger Side Peripheral Acceleration Sensor - Incorrect assembly	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 incorrect assembly	Check that the passenger side impact sensor 1 is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B10FE-96	Passenger Side Peripheral Acceleration Sensor - Component internal failure	NOTE: Circuit reference SENSOR-ACCEL PASS 1+ / SENSOR-ACCEL PASS 1- Passenger side impact sensor 1 internal fault	Refer to the electrical circuit diagrams and test the passenger side impact sensor 1
B1126-11	Drivers Side-Side Airbag Deployment Control - Circuit short to ground	NOTE: Circuit reference SIDE AIRBAG DRIVER+ / SIDE AIRBAG DRIVER- Driver side airbag circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver side airbag circuit for short circuit to ground
B1126-12	Drivers Side-Side Airbag Deployment Control - Circuit short to battery	NOTE: Circuit reference SIDE AIRBAG DRIVER+ / SIDE AIRBAG DRIVER- Driver side airbag circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver side airbag circuit for short circuit to power
B1126-13	Drivers Side-Side Airbag Deployment Control - Circuit open	NOTE: Circuit reference SIDE AIRBAG DRIVER+ / SIDE AIRBAG DRIVER- Driver side airbag circuit open circuit	Refer to the electrical circuit diagrams and test the driver side airbag circuit for open circuit
B1126-19	Drivers Side-Side Airbag Deployment Control - Circuit current above threshold	NOTE: Circuit reference SIDE AIRBAG DRIVER+ / SIDE AIRBAG DRIVER- Driver side airbag circuit short circuit	Refer to the electrical circuit diagrams and test the driver side airbag circuit for short circuit
B1126-1A	Drivers Side-Side Airbag Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference SIDE AIRBAG DRIVER+ / SIDE AIRBAG DRIVER- Driver side airbag circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver side airbag circuit for short circuit between both lines to the airbag
B1126-95	Drivers Side-Side Airbag Deployment Control - Incorrect assembly	NOTE: Circuit reference SIDE AIRBAG DRIVER+ / SIDE AIRBAG DRIVER- Driver side airbag incorrect assembly	Check that the driver side airbag is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1127-11	Passengers Side-Side Airbag Deployment Control - Circuit short to ground	NOTE: Circuit reference SIDE AIRBAG PASS+ / SIDE AIRBAG PASS- Passenger side airbag circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger side airbag circuit for short circuit to ground
B1127-12	Passengers Side-Side Airbag Deployment Control - Circuit short to battery	NOTE: Circuit reference SIDE AIRBAG PASS+ / SIDE AIRBAG PASS- Passenger side airbag circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger side airbag circuit for short circuit to power
B1127-13	Passengers Side-Side Airbag Deployment Control - Circuit open	NOTE: Circuit reference SIDE AIRBAG PASS+ / SIDE AIRBAG PASS- Passenger side airbag circuit open circuit	Refer to the electrical circuit diagrams and test the passenger side airbag circuit for open circuit
B1127-19	Passengers Side-Side Airbag Deployment Control - Circuit current above threshold	NOTE: Circuit reference SIDE AIRBAG PASS+ / SIDE AIRBAG PASS- Passenger side airbag circuit short circuit	Refer to the electrical circuit diagrams and test the passenger side airbag circuit for short circuit
B1127-1A	Passengers Side-Side Airbag Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference SIDE AIRBAG PASS+ / SIDE AIRBAG PASS- Passenger side airbag circuit resistance below threshold	Refer to the electrical circuit diagrams and test the passenger side airbag circuit for short circuit between both lines to the side airbag
B1127-95	Passengers Side-Side Airbag Deployment Control - Incorrect assembly	NOTE: Circuit reference SIDE AIRBAG PASS+ / SIDE AIRBAG PASS- Passenger side airbag incorrect assembly	Check that the passenger side airbag is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1128-11	Drivers Side-Side Inflatable Curtain Deployment Control - Circuit short to ground	NOTE: Circuit reference CURTAIN DRIVER+ / CURTAIN DRIVER- Driver side air curtain circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver side air curtain circuit for short circuit to ground
B1128-12	Drivers Side-Side Inflatable Curtain Deployment Control - Circuit short to battery	NOTE: TRAIN DRIVER+ / CURTAIN DRIVER- Driver side air curtain circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver side air curtain circuit for short circuit to power
B1128-13	Drivers Side-Side Inflatable Curtain Deployment Control - Circuit open	NOTE: TRAIN DRIVER+ / CURTAIN DRIVER- Driver side air curtain circuit open circuit	Refer to the electrical circuit diagrams and test the driver side air curtain circuit for open circuit
B1128-19	Drivers Side-Side Inflatable Curtain Deployment Control - Circuit current above threshold	NOTE: Circuit reference CURTAIN DRIVER+ / CURTAIN DRIVER- Driver side air curtain circuit short circuit	Refer to the electrical circuit diagrams and test the driver side air curtain circuit for short circuit
B1128-1A	Drivers Side-Side Inflatable Curtain Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference CURTAIN DRIVER+ / CURTAIN DRIVER- Driver side air curtain circuit resistance below threshold	Refer to the electrical circuit diagrams and test the driver side air curtain circuit for short circuit between both lines to the side air curtain
B1128-95	Drivers Side-Side Inflatable Curtain Deployment Control - Incorrect assembly	NOTE: Circuit reference CURTAIN DRIVER+ / CURTAIN DRIVER- Driver side air curtain incorrect assembly	Check that the driver side air curtain is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1129-11	Passengers Side-Side Inflatable Curtain Deployment Control - Circuit short to ground	NOTE: Circuit reference CURTAIN PASS+ / CURTAIN PASS- Passenger side air curtain circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger side air curtain circuit for short circuit to ground
B1129-12	Passengers Side-Side Inflatable Curtain Deployment Control - Circuit short to battery	NOTE: Circuit reference CURTAIN PASS+ / CURTAIN PASS- Passenger side air curtain circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger side air curtain circuit for short circuit to power
B1129-13	Passengers Side-Side Inflatable Curtain Deployment Control - Circuit open	NOTE: Circuit reference CURTAIN PASS+ / CURTAIN PASS- Passenger side air curtain circuit open circuit	Refer to the electrical circuit diagrams and test the passenger side air curtain circuit for open circuit
B1129-19	Passengers Side-Side Inflatable Curtain Deployment Control - Circuit current above threshold	NOTE: Circuit reference CURTAIN PASS+ / CURTAIN PASS- Passenger side air curtain circuit short circuit	Refer to the electrical circuit diagrams and test the passenger side air curtain circuit for short circuit
B1129-1A	Passengers Side-Side Inflatable Curtain Deployment Control - Circuit resistance below threshold	NOTE: Circuit reference CURTAIN PASS+ / CURTAIN PASS- Passenger side air curtain circuit resistance below threshold	Refer to the electrical circuit diagrams and test the passenger side air curtain circuit for short circuit between both lines to the side air curtain
B1129-95	Passengers Side-Side Inflatable Curtain Deployment Control - Incorrect assembly	NOTE: Circuit reference CURTAIN PASS+ / CURTAIN PASS- Passenger side air curtain incorrect assembly	Check that the passenger side air curtain is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1193-68	Crash Event Storage Full and Locked - Event information	Restraints control module crash event storage area full and locked	Read out the event data recorder and then refer to the warranty policy and procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new restraints control module
B1194-11	Driver Side Frontal Acceleration Sensor - Circuit short to ground	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver front impact sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver front impact sensor circuit for short circuit to ground
B1194-12	Driver Side Frontal Acceleration Sensor - Circuit short to battery	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver front impact sensor circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver front impact sensor circuit for short circuit to power
B1194-19	Driver Side Frontal Acceleration Sensor - Circuit current above threshold	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver front impact sensor circuit short circuit	Refer to the electrical circuit diagrams and test the driver front impact sensor circuit for short circuit
B1194-4A	Driver Side Frontal Acceleration Sensor - Incorrect component installed	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver front impact sensor incorrect component installed	Restraints control module detected a mis-match between the hardware fitted and what is expected Check that the correct driver front impact sensor is installed
B1194-87	Driver Side Frontal Acceleration Sensor - Missing message	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver's side front impact sensor circuit open circuit Driver's side front impact sensor internal fault	Refer to electrical circuit diagrams and driver's side front impact sensor for communication fault
B1194-95	Driver Side Frontal Acceleration Sensor - Incorrect assembly	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver's side front impact sensor incorrect assembly	Check driver's side front impact sensor is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1194-96	Driver Side Frontal Acceleration Sensor - Component internal failure	NOTE: Circuit reference SENSOR UPFRONT DRIV+ / SENSOR UPFRONT DRIV- Driver's side front impact sensor internal fault	Refer to the electrical circuit diagrams and test the driver front impact sensor
B1195-11	Passenger Side Frontal Acceleration Sensor - Circuit short to ground	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger front impact sensor circuit for short circuit to ground
B1195-12	Passenger Side Frontal Acceleration Sensor - Circuit short to battery	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger front impact sensor circuit for short circuit to power
B1195-19	Passenger Side Frontal Acceleration Sensor - Circuit current above threshold	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor circuit short circuit	Refer to the electrical circuit diagrams and test the passenger front impact sensor circuit for short circuit
B1195-4A	Passenger Side Frontal Acceleration Sensor - Incorrect component installed	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor incorrect component installed	Restraints control module detected a mis-match between the hardware fitted and what is expected Check that the correct passenger front impact sensor is installed
B1195-87	Passenger Side Frontal Acceleration Sensor - Missing message	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor circuit open circuit Passenger side front impact sensor internal fault	Refer to the electrical circuit diagrams and test the passenger front impact sensor for communication fault
B1195-95	Passenger Side Frontal Acceleration Sensor - Incorrect assembly	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor incorrect assembly	Check that the passenger front impact sensor is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1195-96	Passenger Side Frontal Acceleration Sensor - Component internal failure	NOTE: Circuit reference SENSOR UPFRONT PASS+ / SENSOR UPFRONT PASS- Passenger front impact sensor internal fault	Refer to the electrical circuit diagrams and test the passenger front impact sensor
B1196-11	Driver Side Second Row Peripheral Acceleration Sensor - Circuit short to ground	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 circuit short circuit to ground	Refer to the electrical circuit diagrams and test the driver side impact sensor 2 circuit for short circuit to ground
B1196-12	Driver Side Second Row Peripheral Acceleration Sensor - Circuit short to battery	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 circuit short circuit to power	Refer to the electrical circuit diagrams and test the driver side impact sensor 2 circuit for short circuit to power
B1196-19	Driver Side Second Row Peripheral Acceleration Sensor - Circuit current above threshold	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 circuit short circuit	Refer to the electrical circuit diagrams and test the driver side impact sensor 2 circuit for short circuit
B1196-4A	Driver Side Second Row Peripheral Acceleration Sensor - Incorrect component installed	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 incorrect component installed	Restraints control module detected a mis-match between the hardware fitted and what is expected Check that the correct driver side impact sensor 2 is installed
B1196-87	Driver Side Second Row Peripheral Acceleration Sensor - Missing message	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 circuit open circuit Driver side impact sensor 2 internal fault	Refer to the electrical circuit diagrams and test the driver side impact sensor 2 for communication fault
B1196-95	Driver Side Second Row Peripheral Acceleration Sensor - Incorrect assembly	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 incorrect assembly	Check that the driver side impact sensor 2 is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1196-96	Driver Side Second Row Peripheral Acceleration Sensor - Component internal failure	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Driver side impact sensor 2 internal fault	Refer to the electrical circuit diagrams and test the driver side impact sensor 2
B1197-11	Passenger Side Second Row Peripheral Acceleration Sensor - Circuit short to ground	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Passenger's side rear side impact sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and check passenger's side rear side impact sensor circuit for short circuit to ground
B1197-12	Passenger Side Second Row Peripheral Acceleration Sensor - Circuit short to battery	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Passenger side impact sensor 2 circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger side impact sensor 2 circuit for short circuit to power
B1197-19	Passenger Side Second Row Peripheral Acceleration Sensor - Circuit current above threshold	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Passenger side impact sensor 2 circuit short circuit	Refer to the electrical circuit diagrams and test the passenger side impact sensor 2 circuit for short circuit
B1197-4A	Passenger Side Second Row Peripheral Acceleration Sensor - Incorrect component installed	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Passenger side impact sensor 2 incorrect component installed	Restraints control module detected a mis-match between the hardware fitted and what is expected Check that the correct passenger side impact sensor 2 is installed
B1197-87	Passenger Side Second Row Peripheral acceleration Sensor - Missing message	NOTE: Circuit reference SENSOR-ACCEL DRIV 2+ / SENSOR-ACCEL DRIV 2- Passenger side impact sensor 2 circuit open circuit Passenger side impact sensor 2 internal fault	Refer to the electrical circuit diagrams and test the passenger side impact sensor 2 for communication fault
B1197-95	Passenger Side Second Row Peripheral Acceleration Sensor - Incorrect assembly	NOTE: Circuit reference SENSOR-ACCEL PASS 2+ / SENSOR-ACCEL PASS 2- Passenger's side rear side impact sensor incorrect assembly	Check that the passenger side impact sensor 2 is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1197-96	Passenger Side Second Row Peripheral Acceleration Sensor - Component internal failure	NOTE: Circuit reference SENSOR-ACCEL PASS 2+ / SENSOR-ACCEL PASS 2- Passenger side impact sensor 2 internal fault	Refer to the electrical circuit diagrams and test the passenger side impact sensor 2
B1A55-11	Crash Record Output - Circuit short to ground	Event signal circuit short circuit to ground	Refer to the electrical circuit diagrams and check event signal circuit for short circuit to ground
B1A55-12	Crash Record Output - Circuit short to battery	Event signal circuit short circuit to power	Refer to the electrical circuit diagrams and check event signal circuit for short circuit to power
B1D74-11	Passenger Airbag Cutoff Enable Switch - Circuit short to ground	Passenger airbag deactivation switch circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch circuit for short circuit to ground
B1D74-12	Passenger Airbag Cutoff Enable Switch - Circuit short to battery	Passenger's air bag deactivation switch circuit short circuit to power	Refer to the electrical circuit diagrams and check passenger's air bag deactivation switch circuit for short circuit to power
B1D74-13	Passenger Airbag Cutoff Enable Switch - Circuit open	Passenger's air bag deactivation switch circuit open circuit	Refer to the electrical circuit diagrams and check passenger's air bag deactivation switch circuit for open circuit
B1D74-19	Passenger Airbag Cutoff Enable Switch - Circuit current above threshold	Passenger airbag deactivation switch circuit short circuit	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch circuit for short circuit
B1D74-1E	Passenger Airbag Cutoff Enable Switch - Circuit resistance out of range	Passenger airbag deactivation switch circuit resistance out of range	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch for resistance out of range
B1D74-95	Passenger Airbag Cutoff Enable Switch - Incorrect assembly	Passenger's air bag deactivation switch incorrect assembly	Check passenger's air bag deactivation switch installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
B1D75-11	Passenger Airbag Cutoff Disable Switch - Circuit short to ground	Passenger's air bag deactivation switch circuit short circuit to ground	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch circuit for short circuit to ground
B1D75-12	Passenger Airbag Cutoff Disable Switch - Circuit short to battery	Passenger's air bag deactivation switch circuit short circuit to power	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch circuit for short circuit to power
B1D75-13	Passenger Airbag Cutoff Disable Switch - Circuit open	Passenger's air bag deactivation switch circuit open circuit	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch circuit for open circuit
B1D75-19	Passenger Airbag Cutoff Disable Switch - Circuit current above threshold	Passenger airbag deactivation switch circuit short circuit	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch circuit for short circuit
B1D75-1E	Passenger Airbag Cutoff Disable Switch - Circuit resistance out of range	Passenger's air bag deactivation switch circuit resistance out of range	Refer to the electrical circuit diagrams and test the passenger airbag deactivation switch for resistance out of range
B1D75-95	Passenger Airbag Cutoff Disable Switch - Incorrect assembly	Passenger's air bag deactivation switch incorrect assembly	Check that the passenger airbag deactivation switch is installed correctly Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
U0001-88	High Speed CAN Communication Bus - Bus off	High speed CAN bus circuit fault	Using the manufacturer approved diagnostic system, complete a CAN network integrity test Refer to the electrical circuit diagrams and test the CAN network
U0140-00	Lost Communication With Body Control Module - No sub type information	Lost communication with the central junction box	Refer to the electrical circuit diagrams and test the power and ground connections to the central junction box Using the manufacturer approved diagnostic system, complete a CAN network integrity test Refer to the electrical circuit diagrams and test the CAN network between the restraints control module and the central junction box
U0154-00	Lost Communication With Restraints Occupant Classification System Module - No sub type information	Lost communication with the occupant classification sensor control module	Refer to the electrical circuit diagrams and test the power and ground connections to the occupant classification sensor control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test Refer to the electrical circuit diagrams and test the CAN network between the restraints control module and occupant classification sensor control module
U0300-00	Internal Control Module Software Incompatibility - No sub type information	Restraints control module is not configured correctly	Using the manufacturer approved diagnostic system check and install latest relevant level of software to the restraints control module
U0455-64	Invalid Data Received From Restraints Occupant Classification System Module - Signal plausibility failure	Restraints occupant classification system module configuration error	Using the manufacturer approved diagnostic system, check and install the latest relevant level of software to the occupant classification sensor control module
U0455-92	Invalid Data Received From Restraints Occupant Classification System Module - Performance or incorrect operation	Restraints occupant classification system module internal failure	Refer to the electrical circuit diagrams and test the occupant classification sensor control module for internal fault, and check for stored DTCs
U0455-94	Invalid Data Received From Restraints Occupant Classification System Module - Unexpected operation	Restraints occupant classification system module unexpected operation	Using the manufacturer approved diagnostic system, check and install the latest relevant level of software to the occupant classification sensor control module
U2100-00	Initial Configuration Not Complete - No sub type information	Restraints control module is not configured correctly	Using the manufacturer approved diagnostic system, check and install the latest relevant level of software to the occupant classification sensor control module
U2101-00	Control Module Configuration Incompatible - No sub type information	Restraints control module is not configured correctly	Using the manufacturer approved diagnostic system, check and install the latest relevant level of software to the restraints control module Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary. Clear the DTC and re-test
U3000-49	Control Module - Internal electronic failure	Restraints control module internal electronic failure	Restraints control module internal fault
U3003-62	Battery Voltage - Signal compare failure	Restraints control module measured voltage is 2.5v lower than battery voltage	Refer to the electrical circuit diagrams and test the input voltage to the restraints control module compared to battery voltage
U3006-17	Control Module Input Power 'A' - Circuit voltage above threshold	Restraints control module circuit supply voltage above threshold	Refer to the electrical circuit diagrams and check for high input voltage to the restraints control module
U3006-68	Control Module Input Power 'A' - Event information	Restraints control module circuit supply voltage below threshold	Refer to the electrical circuit diagrams and test for low input voltage to the restraints control module
U3008-13	Control Module Ground 'A' - Circuit open	Restraints control module ground supply open circuit	Refer to the electrical circuit diagrams and check the ground supply for open circuit to the restraints control module