LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2018 >> Soul Base, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 13 (Automatic Transaxle System - 2.0L) >> Automatic Transaxle >> Repair Procedures >> Removal

Repair Procedures: Removal

WARNING: This page is about a different variant/trim than selected.
  1. Remove the air cleaner assembly.

    (Refer to Engine Mechanical System -AIR CLEANER ")

  2. Remove the battery and battery tray.

    (Refer to Engine Electrical System -BATTERY ")

  3. Remove the ground line after removing the bolt (A).
    Fig 1: Locating Ground Line Bolt
    G12239524Courtesy of KIA MOTORS AMERICA, INC.
  4. Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).
    Fig 2: Disconnecting Solenoid Valve Connector And Inhibitor Switch Connector
    G12239525Courtesy of KIA MOTORS AMERICA, INC.
  5. Remove the wiring brackets (A, B, C).

    Tightening torque: 

    (A, C) 9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    (B) 14.7 - 21.6 N.m (1.5 - 2.2 kgf.m, 10.8 - 15.9 lb.ft)

    Fig 3: Locating Wiring Brackets With Bolts
    G12239526Courtesy of KIA MOTORS AMERICA, INC.
    Fig 4: Locating Wiring Bracket Bolt
    G12239527Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the shift cable (C) after removing the nut (A) and bolts (B).

    Tightening torque: 

    1. 9.8 - 13.7 N.m (1.0-1.4 kgf.m, 7.2 -10.1 lb.ft)
    2. 14.7 - 21.6 N.m (1.5-2.2 kgf.m, 10.9 - 15.9 lb.ft)
    Fig 5: Locating Shift Cable, Nut And Bolts
    G12239528Courtesy of KIA MOTORS AMERICA, INC.
  7. Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).
    Fig 6: Locating Automatic Transaxle Fluid Cooler Hose And Clamp
    G12239529Courtesy of KIA MOTORS AMERICA, INC.
  8. Remove the automatic transaxle upper mounting bolts (A) and the starter mounting bolts (B).

    Tightening torque: 

    1. 42.2 - 54.0 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb.ft)
    2. 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb.ft)
    Fig 7: Locating Automatic Transaxle Upper Mounting Bolts And Starter Mounting Bolts
    G12239530Courtesy of KIA MOTORS AMERICA, INC.
  9. Install the engine support fixture.
    1. Loosen the bolts (A) from both side.
    2. Assemble the engine support fixture.

      (Refer to Special Service Tools - "ENGINE SUPPORT FIXTURE ASSEMBLY DRAWING ")

      Fig 8: Installing Engine Support Fixture
      G12239531Courtesy of KIA MOTORS AMERICA, INC.
  10. Remove the cover (A).
    Fig 9: Locating Cover
    G12239532Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the transaxle mounting bracket bolts (A).

    Tightening torque: 

    88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.8 lb.ft)

    Fig 10: Locating Transaxle Mounting Bracket Bolts
    G12239533Courtesy of KIA MOTORS AMERICA, INC.
  12. Remove the transaxle support bracket (A).

    Tightening torque: 

    58.9 - 78.5 N.m (6.0 - 8.0 kgf.m, 43.4 - 57.9 lb.ft)

    Fig 11: Locating Transaxle Support Bracket With Bolts
    G12239534Courtesy of KIA MOTORS AMERICA, INC.
  13. Lift the vehicle with a jack.
  14. Remove the under cover and side cover.

    (Refer to Engine Mechanical System - ENGINE ROOM UNDER COVER ")

  15. Remove the drive shaft assembly.

    (Refer to Driveshaft and Axle - "FRONT DRIVESHAFT ")

  16. Remove the heat protector (A).

    Tightening torque: 

    19.6 - 29.4 N.m (2.0 - 3.0 kgf.m, 14.5 - 21.7 lb.ft)

    Fig 12: Locating Heat Protector With Bolts
    G12239535Courtesy of KIA MOTORS AMERICA, INC.
  17. Remove the air guide bracket (A).

    Tightening torque: 

    8.8 - 13.7 N.m (0.9 -1.4 kgf.m, 6.5 - 10.1 lb.ft)

    Fig 13: Locating Air Guide Bracket With Bolts
    G12239536Courtesy of KIA MOTORS AMERICA, INC.
  18. Remove the dust cover (A).

    Tightening torque: 

    42.2 - 53.9 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb.ft)

    Fig 14: Locating Dust Cover
    G12239537Courtesy of KIA MOTORS AMERICA, INC.
  19. Remove the torque converter mounting bolts (A) with rotating the crankshaft.

    Tightening torque: 

    45.1 - 52.0 N.m (4.6 - 5.3 kgf.m, 33.3 - 38.3 lb.ft)

    Fig 15: Locating Torque Converter Mounting Bolts
    G12239538Courtesy of KIA MOTORS AMERICA, INC.
  20. Remove the roll rod bracket (C) after removing bolts (A, B).

    Tightening torque: 

    1. 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47 lb.ft)
    2. 107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94 lb.ft)
    Fig 16: Locating Roll Rod Bracket And Bolts
    G12239539Courtesy of KIA MOTORS AMERICA, INC.
  21. Remove the mounting bolts (A, B) after supporting the transaxle by a jack.

    Tightening torque: 

    1. 42.2 - 48.1 N.m (4.3 - 4.9 kgf.m, 31.1 - 35.4 lb.ft)
    2. 42.2 - 53.9 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb.ft)
    Fig 17: Locating Transaxle Mounting Bolts
    G12239540Courtesy of KIA MOTORS AMERICA, INC.
  22. Remove the transaxle while slowly lower the jack.
    NOTE: Be careful not to damage other system or parts near by when removing the transaxle assembly.
scientia non olet · About LEMON Manuals