Common Specs & Procedures
SEDONA COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Axle Nut/Hub Nut | |||
| Front | 177-199 ft. lbs. (245-275 N.m) | ||
| Rear (Lock Nut) | 145-188 ft. lbs. (200-260 N.m) | ||
| Battery | See Battery under SPECIFICATION | ||
| Brakes | |||
| Bleeding Sequence | See Bleeding Of Brake System under BRAKE SYSTEM BLEEDING or ESC BLEEDING OF BRAKE SYSTEM . | ||
| Disc Brakes | Refer to SPECIFICATIONS . | ||
| Drum Brakes | N/A | ||
| Torque | Refer to TIGHTENING TORQUES . | ||
| Charging | |||
| Generator | Refer to Alternator Specification under SPECIFICATION . | ||
| Torque | Refer to TIGHTENING TORQUES . | ||
| Drive Belts | |||
| Adjustment | N/A | ||
| Belt Routing | Refer to Drive Belt Routing figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | See Cooling System in table under ENGINE MECHANICAL SYSTEM - GENERAL INFORMATION . | ||
| Capacity | Approx. 12.15 Qts. (11.5L) | ||
| Radiator Cap Pressure | |||
| Main Valve Opening Pressure | 13.51-17.78 psi (93.16-122.58 kPa) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | COMPRESSION PRESSURE INSPECTION | ||
| Oil pressure | At 1000 RPM and with oil temperature 230°F (110°C), normal oil pressure should be at least 18.77 psi (1.32 kg/cm2 ) or 130 kPa. | ||
| Overhaul | ENGINE MECHANICAL SYSTEM | ||
| Torque | TIGHTENING TORQUES | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| Flexplate-To-Crankshaft Bolt | 52.8-55.9 ft. lbs. (71.6-75.5 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | Fuel filter is part of fuel pump. | ||
| Low Pressure Fuel Line Specification | 470.7-519.8 kPa (4.8-5.3 kgf/cm2 , 68.3-75.4 psi) | ||
| High Pressure Fuel Line Specification | 2.0-14.7 MPa (20.0-150.0 kgf/cm2 , 284.5-2133.5 psi) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) | ||
| Fuel Pressure Release Procedure | RELEASE RESIDUAL PRESSURE IN FUEL LINE | ||
| Fuel Filter R & I | Fuel filter is part of fuel pump. Refer to REPAIR PROCEDURES for removal and installation. | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-2-3-4-5-6: Also refer to FIRING ORDER & CYLINDER IDENTIFICATION article. | ||
| Ignition Wires (Resistance) | Coil On Plug N/A | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plug | Refer to SPECIFICATION | ||
| Starting | |||
| Starter | Refer to Starting System under SPECIFICATION | ||
| Torque | Refer to TIGHTENING TORQUES . | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to WHEEL ALIGNMENT . | ||
| Torque | TIGHTENING TORQUES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 65.1-79.6 ft. lbs. (88.3-107.9 N.m) | ||