Common Specs & Procedures Index
SOUL COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | See TIGHTENING TORQUE SPECIFICATION table under WHEN INSTALLING CONNECTING PARTS . | ||
| Axle Nut/Hub Nut | 177-198 ft. lb. (240.2-269.6 N.m) | ||
| Battery | |||
| 1.6L | CHARGING SYSTEM | ||
| 2.0L | CHARGING SYSTEM | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Drum Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Charging | |||
| Generator | |||
| 1.6L | CHARGING SYSTEM | ||
| 2.0L | CHARGING SYSTEM | ||
| Torque | |||
| 1.6L | Refer to tightening torque in text under REPLACEMENT . | ||
| 2.0L | TIGHTENING TORQUE | ||
| Drive Belts | |||
| Adjustment | |||
| 1.6L | DRIVE BELT TENSION MEASUREMENT AND ADJUSTMENT | ||
| 2.0L | ALTERNATOR BELT INSPECTION AND ADJUSTMENT | ||
| Drive Belt Routing | |||
| 1.6L | See Identifying Drive Belt figure under REPLACEMENT . | ||
| 2.0L | See Figure under ALTERNATOR BELT INSPECTION AND ADJUSTMENT . | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 1.6L | See Cooling System in table under SPECIFICATIONS . | ||
| 2.0L | See Coolant in table underSPECIFICATIONS | ||
| Radiator Cap Pressure | |||
| 1.6L | 13.51-17.78 psi (93.16-122.58 kPa) | ||
| 2.0L | 13.51-17.78 psi (93.16-122.58 kPa) | ||
| Thermostat R & I | |||
| 1.6L | REPAIR PROCEDURES | ||
| 2.0L | REPAIR PROCEDURES | ||
| Water Pump R & I | |||
| 1.6L | REPAIR PROCEDURES | ||
| 2.0L | REPAIR PROCEDURES | ||
| Engine Mechanical | |||
| 1.6L | |||
| Compression | COMPRESSION PRESSURE INSPECTION | ||
| Oil Pressure | 14.5 psi (100 kPa) or above at 1000 RPM with oil temperature at 230± 36°F (110±2°C). | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| 2.0L | |||
| Compression | COMPRESSION PRESSURE | ||
| Oil pressure | 14.5 psi (100 kPa) at 800 RPM with oil temperature at 194-212°F (90-100°C). | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 1.6L | 52.8-55.7 ft. lbs. (71.6-75.5 N.m) | ||
| 2.0L | 86.8-94 ft. lbs. (117.7-127.5 N.m) | ||
| Fuel System | |||
| Pressure Specification | 48.4-50.0 psi (333-345 kPa) | ||
| Fuel Pressure Test Procedure | |||
| 1.6L | FUEL PRESSURE TEST | ||
| 2.0L | FUEL PRESSURE TEST | ||
| Fuel Filter Location | |||
| 1.6L | Fuel filter is part of fuel pump. See appropriate Figure under REPLACEMENT . | ||
| 2.0L | Fuel filter is part of fuel pump. See appropriate Figure under REPLACEMENT . | ||
| Fuel Filter R & I | |||
| 1.6L | REPLACEMENT | ||
| 2.0L | REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-3-4-2. No. 1 cylinder is closest to water pump. Also refer to FIRING ORDER & CYLINDER IDENTIFICATION . | ||
| Ignition Coil (Resistance) | |||
| 1.6L | IGNITION SYSTEM | ||
| 2.0L | IGNITION SYSTEM | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 1.6L (Type: RER8MC) | |||
| Gap | 0.0394-0.0433 in. (1.0-1.1 mm) | ||
| Torque | N/A | ||
| 2.0L (Type: IZFR5L-11) | |||
| Gap | 0.0394-0.0433 in. (1.0-1.1 mm) | ||
| Torque | 15-21 ft. lb. (20-30 N.m) | ||
| Starting | |||
| Starter | |||
| 1.6L | STARTING SYSTEM | ||
| 2.0L | STARTING SYSTEM | ||
| Torque | |||
| 1.6L | Starter Bolts - 31.1-39.8 ft. lbs. (42.2-53.9 N.m) | ||
| 2.0L | TIGHTENING TORQUE | ||
| Wheel Alignment | |||
| Adjustment Specifications | REPAIR PROCEDURES | ||
| Torque | TIGHTENING TORQUES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 65-80 ft. lbs. (90-110 N.m) | ||