Tightening Torque
TIGHTENING TORQUE SPECIFICATION
| Items | N.m | kg-cm | lb-ft |
|---|---|---|---|
| Wiring harness bracket | 20-26 | 200-260 | 14-18 |
| Control cable bracket | 8-12 | 80-120 | 6-8 |
| Eye bolt | 30-45 | 300-450 | 21-32 |
| Oil cooler feed tube | 10-12 | 100-120 | 7-8 |
| Input shaft speed sensor | 10-12 | 100-120 | 7-8 |
| Output shaft speed sensor | 10-12 | 100-120 | 7-8 |
| Manual control lever | 18-25 | 180-250 | 13-18 |
| Transaxle range switch | 10-12 | 100-120 | 7-8 |
| Vehicle speed sensor | 4-6 | 40-60 | 3-4 |
| Valve body cover | 8-10 | 80-100 | 6-7 |
| Valve body mounting bolt | 10-12 | 100-120 | 7-8 |
| Oil temperature sensor | 10-12 | 100-120 | 7-8 |
| Manual control shaft detent | 5-7 | 50-70 | 4-5 |
| Rear cover | 20-26 | 200-260 | 14-18 |
| Torque converter housing | 42-54 | 420-540 | 29-38 |
| Oil pump mounting bolt | 20-26 | 200-260 | 14-18 |
| Transfer drive gear | 31-36 | 320-370 | 23-27 |
| Output shaft lock nut | 160-180 | 1600-1800 | 110-126 |
| Output shaft bearing retainer | 20-26 | 200-260 | 14-18 |
| Oil filler tube | 29-34 | 290-340 | 20-24 |
| Oil drain plug | 40-50 | 400-500 | 29-36 |
| Transfer drive gear lock nut | 180-210 | 1800-2100 | 126-147 |
| Differential drive gear | 130-140 | 1300-1400 | 91-98 |
| Valve body | 10-12 | 100-120 | 7-8 |
| Solenoid valve support | 5-7 | 50-70 | 4-5 |
| Plate | 5-7 | 50-70 | 4-5 |
| Pressure check plug | 8-10 | 80-100 | 6-7 |
| Transaxle mounting subframe nut | 100-120 | 1000-1200 | 72-87 |
| Transaxle mounting subframe bolt | 100-120 | 1000-1200 | 72-87 |
| Transaxle mounting bolts | 60-80 | 600-800 | 43-58 |
| Transaxle mounting nut | 60-80 | 600-800 | 43-58 |
| Reduction brake band ankor plug | 85-115 | 850-1150 | 61-83 |
| Reduction brake piston rod nut | 15-22 | 150-220 | 11-16 |
| Tie rod end ball joint | 24-34 | 240-340 | 17-24 |
| Lower arm ball joint mounting bolt | 100-120 | 1000-1200 | 72-87 |
| Drive shaft nut | 200-280 | 2000-2800 | 145-203 |
| Muffler mounting nut | 40-60 | 400-600 | 29-43 |
| Shift lever mounting bolt | 9-14 | 90-140 | 7-10 |
| Shift lock cable fixing nut | 8-12 | 80-120 | 6-8 |
WARNING:
ALWAYS FOLLOW TORQUE TIGHTENING LEVELS. FAILURE TO FOLLOW SUCH LEVELS CAN RESULT IN PARTS BREAKING IF OVER-TIGHTENED OR LOOSENING IF UNDER-TIGHTENED. IN EITHER CASE, SERIOUS PERSONAL INJURY OR DEATH COULD RESULT TO THE VEHICLE OCCUPANTS.