Diagnostic Test

CHECK FOR ANY SERVICE BULLETINS OR MODULE SOFTWARE UPDATES
1. Check for any applicable Service Bulletins or Flash updates related to the DTC.
  Are there any applicable Service Bulletins or Flash updates?
  
  Yes
  - Perform the applicable repair.
  - Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .
  No
  - Go To 2
READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, run and save a vehicle Scan Report and all related recorded data.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 10.0 seconds.
5. Turn the ignition on.
6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to: TESTING FOR AN INTERMITTENT CONDITION .
PASSENGER OUTSIDE REARVIEW MIRROR
1. Turn the ignition off.
2. Disconnect the Passenger Outside Rearview Mirror harness connector.
3. Turn the ignition on.
4. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read DTCs.
  Does the scan tool display this DTC as active?
  
  Yes
  - Go To 4
  No
  - Replace the Passenger Outside Rearview Mirror in accordance with the Service Information. Refer to MIRROR, OUTSIDE REARVIEW, REMOVAL AND INSTALLATION MIRROR, OUTSIDE REARVIEW, GLASS, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .
CHECK THE (P712) RIGHT BLIND SPOT INDICATOR DRIVER CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the RBSS harness connector.
3. Check for continuity between ground and the (P712) Right Blind Spot Indicator Driver circuit at the RBSS harness connector.
  Is there continuity between ground and the (P712) Right Blind Spot Indicator Driver circuit?
  
  Yes
  - Repair the (P712) Right Blind Spot Indicator Driver circuit for a short to ground.
  - Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .
  No
  - Go To 5
CHECK RELATED RBSS AND COMPONENT CONNECTIONS
1. Disconnect all RBSS harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all RBSS harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read RBSS DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Right Blind Spot Sensor (RBSS) in accordance with the Service Information. Refer to SENSOR, BLIND SPOT, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .
  No
  - The wiring or poor connection has been repaired
  - Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .