Measurement Specifications
NOTE:
Specifications are in degrees.
NOTE:
Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.
| Front Alignment Specifications | |||||||
|---|---|---|---|---|---|---|---|
| Total Toe** | Left Caster | Right Caster | Cross Caster | Left Camber | Right Camber | Cross Camber | |
| Aero Suspension | 0.20° +/- 0.20° | 7.32° +/- 0.60° | 7.32° +/- 0.60° | 0.00° +/- 0.60° | -0.63° +/- 0.60° | -1.03° +/- 0.60° | 0.40° +/- 0.60° |
| Base Suspension (LHD) | 0.20° +/- 0.20° | 6.95° +/- 0.60° | 6.95° +/- 0.60° | 0.00° +/- 0.60° | -0.38° +/- 0.60° | -0.78° +/- 0.60° | 0.40° +/- 0.60° |
| Base Suspension (RHD) | 0.20° +/- 0.20° | 7.15° +/- 0.60° | 6.75° +/- 0.60° | 0.40° +/- 0.60° | -0.88° +/- 0.60° | -0.28° +/- 0.60° | -0.60° +/- 0.60° |
| Air Suspension (Aero Mode) (LHD) | 0.20° +/- 0.20° | 7.55° +/- 0.60° | 7.55° +/- 0.60° | 0.00° +/- 0.60° | -0.75° +/- 0.60° | -1.15° +/- 0.60° | 0.40° +/- 0.60° |
| Air Suspension (Aero Mode) (RHD) | 0.20° +/- 0.20° | 7.75° +/- 0.60° | 7.35° +/- 0.60° | 0.40° +/- 0.60° | -1.25° +/- 0.60° | -0.65° +/- 0.60° | -0.60° +/- 0.60° |
| SRT8 (LHD) (with 3season tires) | 0.20° +/- 0.20° | 6.67° +/- 0.55° | 6.67° +/- 0.55° | 0.00° +/- 0.55° | -1.68° +/- 0.55° | -1.98° +/- 0.55° | 0.30° +/- 0.55° |
| SRT8 (RHD) (with 3 season tires) | 0.20° +/- 0.20° | 6.67° +/- 0.55° | 6.67° +/- 0.55° | 0.00° +/- 0.55° | -1.98° +/- 0.55° | -1.68° +/- 0.55° | -0.30° +/- 0.55° |
| SRT8 (LHD) (with 4 season tires) | 0.20° +/- 0.20° | 6.67° +/- 0.55° | 6.67° +/- 0.55° | 0.00° +/- 0.55° | -1.68° +/- 0.55° | -1.98° +/- 0.55° | 0.30° +/- 0.55° |
| SRT8 (RHD) (with 4 season tires) | 0.20° +/- 0.20° | 6.67° +/- 0.55° | 6.67° +/- 0.55° | 0.00° +/- 0.55° | -1.98° +/- 0.55° | -1.68° +/- 0.55° | -0.30° +/- 0.55° |
| SRT8 (Trackhawk) | 0.20° +/- 0.20° | 7.00° +/- 1.00° | 7.00° +/- 1.00° | 0.00° +/- 1.00° | -1.68° +/- 0.55° | -1.98° +/- 0.55° | 0.30° +/- 0.55° |
| Notes: | |||||||
| Positive toe (+) is toe-in and negative toe (-) is Toe-out. | |||||||
| ** TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. | |||||||
| Rear Alignment Specifications | |||||
|---|---|---|---|---|---|
| LHD and RHD | Toe | Total Toe** | Thrust Angle | Camber | Cross Camber |
| Aero Suspension | 0.10° +/- 0.15° | 0.20° +/- 0.30° | 0.00° +/- 0.15° | -0.88 +/- 0.55 | 0.00° +/- 0.50° |
| Base Suspension | 0.10° +/- 0.15° | 0.20° +/- 0.30° | 0.00° +/- 0.15° | -0.54 +/- 0.55° | 0.00° +/- 0.50° |
| Air Suspension (Aero Mode) | 0.20° +/- 0.15° | 0.40° +/- 0.30° | 0.00° +/- 0.15° | -1.09° +/- 0.55° | 0.00° +/- 0.50° |
| SRT8 | 0.125° +/- 0.10° | 0.25° +/- 0.20° | 0.00° +/- 0.10° | -1.30° +/- 0.50° | 0.00° +/- 0.55° |
| Notes: | |||||
| Positive toe (+) is toe-in and negative toe (-) is Toe-out. | |||||
| ** TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. | |||||